TX3 Series TELEPHONE ACCESS SYSTEMS Installation and Operation Manual Version 3.
(122) LT-969 Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
Contents 1 Introduction 9 1.1 1.2 1.3 1.4 1.5 1.6 1.7 TX3 Systems 10 Features 11 Lobby Control Unit Enclosures 12 Lobby Control Unit Accessories 15 Warranty and Special Notices 16 About This Manual 16 Contact Us 17 2 Enclosure Installation 19 2.1 2.2 2.3 2.4 Grounding the Telephone Access System 20 Installing the Enclosures and Lobby Control Unit 20 Installing the Heater 26 TX3-2000-8K-A 8 Line Kiosk Installation 27 3 TX3 System 33 3.1 3.2 3.3 3.4 3.5 3.6 3.
6 Elevator Restriction Unit Installation and Configuration 87 6.1 6.2 6.3 6.4 6.5 6.6 6.7 Elevator Restriction Cabinet Mechanical Installation 88 Elevator Restriction Units 89 Wiring the Elevator Restriction Unit 91 Elevator Restriction Controller Backplane 94 2012E Elevator Restriction Relay Card 95 Elevator Restriction Unit Configuration 96 Updating Firmware 99 7 Adding Controllers 101 7.1 Adding a Controller 102 8 Appendix 103 8.1 8.2 8.3 8.
List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Version 3.
Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 6 (122) LT-969 Lobby Control Unit with Elevator Restriction 89 Elevator Restriction Unit 90 Elevator Controller Board 91 Elevator Restriction Controller Board Wiring 93 Elevator Restriction Controller Backplane 94 2012E Elevator Restriction Relay Board 95 Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
List of Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Version 3.
(122) LT-969 Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
1 Introduction This manual provides information about the installation and operation of the Telephone Access System, and must be read in its entirety before beginning any installation work. Installation must be performed by a qualified technician and must adhere to the standards and special notices set by the local regulatory bodies. Note: Mircom periodically updates panel firmware and Configurator Software to add features and correct any minor inconsistencies.
Introduction 1.1 TX3 Systems The Mircom's TX3 series of telephone access systems provide high quality twoway communication between residents and their visitors in a multi-unit dwelling establishment. The basic TX3 system consists of the TX3 Lobby Control Unit and depending on the application, may be integrated with a combination of Mircom Elevator Restriction Units, Card Access Units and Touch Screens.
Introduction Units, typically located in the electrical/telephone room of a building. The NSL units intercept all telephone lines into the building’s suites and communicate directly to the resident phone using the Lobby Control Unit. Note: 1.1.2 Non-configurable PBX systems are not supported. For more information, contact technical support at Mircom.
Introduction 1.
Introduction TX3-120U and TX3-120U-A. Stainless steel finish entry panel with speaker, microswitch for postal lock, 200 name main controller board, 4x20 LCD display, 120 name paper directory and one PS-4P transformer plug. Designed for outdoor applications. The TX3-120U-A is IP capable. TX3-200-8U and TX3-200-8U-A. Stainless steel finish entry panel with speaker, microswitch for postal lock, 200 name main controller board, 8x20 LCD display and one PS-4P transformer plug. Designed for outdoor applications.
Introduction • PS-4P transformer plug • TX3-NSL-8M Master NSL Relay Cabinet with one PS-4P transformer plug • 2012K Twelve Telephone Relay Kit with a 2012 Twelve Telephone Relay board and a 9106 Cable • RJ-71C Punch Down Block for outdoor applications TX3-NSL-12K-A. This is the IP capable version of the TX3-NSL-12K and comes with the TX3-200-4U-A panel instead of the TX3-200-4U. The Universal Panel Accessories consist of the following: Model TX3-UFT.
Introduction TX3-1000-8CH and TX3-1000-8CH-A. Stainless steel finish Lobby Control Unit with speaker, microswitch for postal lock, 1000 name main controller board, 8x20 LCD display, handset, flush mounting back box and one PS-4P transformer plug. Designed for indoor use. The TX3-1000-8CH-A is IP capable. TX3-2000-8CH and TX3-2000-8CH-A.
Introduction 1.5 Warranty and Special Notices Mircom values your business and always attempts to provide you with the very best service. Please see the Warranty and Special Notices chapter on page 115 for information about the warranty and special notices about equipment use. 1.6 About This Manual This manual provides comprehensive information on the installation and configuration of the TX3 Series Telephone Access System by the installation technician.
Introduction 1.7 • LT-1160 TX3-CX-A8 Aperio Interface Panel Installation and Operation Manual. • TX3 Telephone Access System User’s Guide LT-968 • TX3 Two Door Card Access System Kit Catalogue Number 6531 • TX3 Series Elevator Restriction Accessories Catalogue Number 6532 Contact Us Mircom fosters a collaborative support process and environment in providing early feedback to meet your specific needs. You can contact us from Monday to Friday 8:00 A.M. to 5:00 P.M. E.S.T. 1.7.
Introduction 1.7.3 Website Visit the Mircom website, at www.mircom.com, to find the product information you are looking for and to learn about troubleshooting, training and technical support options. The website provides avenues for customers to ask questions about new and existing technologies, and receive expert technical support about software and products. Visit www.mircom.com/chat. 1.7.4 Email As a customer you quickly become informed on how we can help with new products and technologies.
2 Enclosure Installation This chapter provides information on how to install the various enclosures and panels. This chapter explains Version 3.
Enclosure Installation 2.1 Grounding the Telephone Access System Grounding reduces the risk of electrical shock by providing an alternate escape route for the electrical current. Telephone Access System is equipped with a 16 gauge electrical wire attached to the panel chassis ground post. To ground the Telephone Access System attach one end of the supplied cable to a suitable grounding wire and connect it to the site ground. 2.
Enclosure Installation 2.2.1 Installing the Universal enclosure The Universal enclosure mounts inside the wall with or without the TX3-UFT Universal Series Flush Trim Ring TX3-UFT. This Trim Ring houses the universal series enclosure as shown in Figure 1. 10 5/8" 19 5/8" 4 1/2 " 16 1/4” 13 1/8 " 2 3/4" Semi-Flush Trim TX3-UFT Universal Enclosure Dimension of the Enclosure without the flush trim. Cut out in wall should be : 16.25” H x 10.6” W x 2.75” D at the bottom 3” at the top Figure 1.
Enclosure Installation 4. Using the semi-flush trim ring as a template, insert the trim ring into the wall cut out and mark the top mounting hole location as shown in Figure 1. Ensure that at least one side is beside a wall stud. 5. Place the screw halfway into the wall into the marked hole location using the supplied screw. 6. Hang the Trim Ring onto the top screw. 7. Screw the lower two screw at the bottom of the trim ring halfway into the wall. 8. Tighten the two screws into place. 9.
Enclosure Installation 3. Using the semi-flush trim ring as a template, insert the trim ring into the wall cut out and mark the top two mounting hole locations as shown in Figure 1. 4. Place the screws halfway into the wall into the marked hole location using the supplied screws. 5. Place the Trim Ring onto the two screws. 6. Screw the lower two screws at the bottom of the trim ring halfway into the wall. 7. Remove the screws and trim ring. 8.
Enclosure Installation 2.2.2 Installing the Universal Slim-line enclosure The Universal enclosure mounts inside the wall with or without the Universal Series Flush Trim Ring TX3-USFT. The Trim Ring houses the universal series enclosure as shown in Figure 2 6 13/32 " 19 5/8" 4 1/2 " 16 1/4" 8 7/8" 2 3/4" TX3-USFT SLIM LINE SEMI-FLUSH TRIM UNIVERSAL SLIM LINE ENCLOSURE Figure 2. Dimension of the Universal Slim Line Enclosure without the flush trim is: 16.25” H x 6.4” W x 2.
Enclosure Installation 2.2.3 Installing the Continental enclosure The Continental enclosure flush mounts directly inside the wall to the wall stud as shown in Figure 3. Mount the back box flush with the wall and right-side up (the ground screw location is at the bottom). WALL 10 3/8" Use the two side slots for mounting the box to the wall stud OUTSIDE FRAME TOP BACKBOX 18 1/2" 16 7/8" MOUNTING KNOCKOUTS FRONT GROUND SCREW LOCATION Cut out in wall should be : 16 7/8” H x 10 3/8” W x 3” D 1 2" 0.
Enclosure Installation 2.3 Installing the Heater For temperatures where the Telephone Access System operates below 0°C (32°F) at any time, a heater must be installed inside the Universal enclosure as shown in Figure 4. For additional information refer to LT-653 TH-102 Heater Installation Instructions. PS-24 TRANSFORMER 120V AC 60 HZ 18 AWG TWISTED PAIR UNIVERSAL ENCLOSURE 24V AC TH-102 HE ATER Figure 4. Heater TH-102 Installation Location To install the heater 1.
Enclosure Installation 2.4 TX3-2000-8K-A 8 Line Kiosk Installation 50.117 " 14.187 " Figure 5 17.950 " Dimensions of the 8 Line Kiosk (inches) The Kiosk mounts to the floor inside the building near the entrance, close to the power source and telephone infrastructure. Access for the power and communication cables is provided through a cutout in the base plate. To install the Kiosk you must: • Remove the reinforcement bracket and the base plate.
Enclosure Installation To install the Touch Screen Kiosk base plate 1. Find a suitable location for the Kiosk next to the building entrance and above the building electrical and communications conduit. 2. Remove the door from the Kiosk. 3. Remove the 4 bolts from the reinforcement bracket, as shown in Figure 6 Reinforcement Bracket Bolts (x4) Figure 6 4. Reinforcement Bracket with bolts Remove the 6 nuts on the reinforcement bracket, as show in Figure 7, and then remove the bracket.
Enclosure Installation Figure 7 5. Reinforcement Bracket with nuts Remove the remaining 8 bolts that attach the Kiosk to the base plate, as shown in Figure 8. Bolts (x8) Base Plate Figure 8 Kiosk Base Plate with bolts The 12 Kiosk mounting holes in the base plate are shown in Figure 9. Cutout Figure 9 Version 3.
Enclosure Installation 6. Using the Kiosk base plate as a template, trace an opening in the floor for the cutout and mark the 4 base plate mounting hole locations as shown in Figure 10. Ensure that the base plate is aligned with the electrical conduit. Base plate mounting holes (x4) Figure 10 Cutout Base Plate Mounting Holes Figure 11 shows the dimensions of the base plate. 50 0 10.300 2.450 2.107 2. 14.244 Figure 11 30 (122) LT-969 Base Plate Dimensions (inches) 7.
Enclosure Installation To fit the Touch Screen Kiosk on the base plate 1. Version 3.2 LT-969 Fit the back lip of the Kiosk into the notches in the baseplate, and tilt the Kiosk forwards so that it rests on top of the base plate.
Enclosure Installation 2. Secure the Kiosk onto the base plate using the 8 of the 12 base plate bolts in the holes shown in Figure 14. Attach the Kiosk to the base plate with bolts in these holes first Figure 14 32 (122) LT-969 Attach the Kiosk to the base plate 3. Position the reinforcement bracket over the 6 studs on the inside of the Kiosk, and screw the 6 nuts on to the studs as shown in Figure 7. 4.
3 TX3 System This chapter provides information about the TX3 System and its use. This chapter explains Version 3.
TX3 System 3.1 TX3 System The TX3 Lobby Control Unit may be networked with a combination of Elevator Restriction Units and Card Access Units through a peer-to-peer RS-485 connection. The TX3 system is capable of providing ADC or NSL telephone access from a single panel or from a networked system. The No Subscriber Line (NSL) controller does not require an outside telephone service and calls residents directly using the existing building’s resident telephone lines.
TX3 System 3.2 Single Lobby Control Unit Figure 15 shows the simplest configuration. Telephone outlet Central office line NSL Control Unit T/R Line1 Line1 OR 3 4 5 6 7 8 9 * 0 # i 2 3 4 5 6 7 8 9 * 0 # i Single Lobby Control Unit Telephone Access System Installation and Operation Manual Copyright 2015 1 Version 3.2 LT-969 2 Figure 15.
TX3 System Figure 16 shows a configuration using one Lobby Control Unit connected to one ADC line and four NSL lines. Telephone outlet Central office line T/R NSL Control Unit NSL Control Unit NSL Control Unit NSL Control Unit T/R T/R T/R T/R Line2 Line4 Line3 Line1 36 (122) LT-969 1 2 3 4 5 6 7 8 9 Figure 16. Line5 * 0 # i Single Lobby Control Unit with ADC and NSL Lines Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
TX3 System Figure 17 shows the various inputs to the panels.
TX3 System The RS-485 network connection is optional and is only required if the user decides to connect a PC configurator on one of the panels to configure and/or monitor both systems. Telephone outlet Central office line NSL Control Unit T/R Line1 Line1 Line1 Line1 Lobby control unit 1 Lobby control unit 1 Lobby control unit 2 2 5 8 0 3 6 9 # i OR 1 4 7 * 2 5 8 0 RS-485 bus (optional) Figure 18. 3.
TX3 System When Lobby Control Unit 1 is using line 1 and Lobby Control Unit 2 also wants to use line1, which is busy, then a line busy message displays on Lobby Control Unit 2. Lobby control unit 1 Lobby control unit 2 NSL Control Unit NSL Control Unit T/R T/R Lobby control unit 3 Line3 Line2 Line1 T/R 1 4 7 * 2 5 8 0 3 6 9 # i 1 4 7 * 2 5 8 0 3 6 9 # i 3 6 9 # i 2 5 8 0 1 4 7 * Telephone outlet Central office line RS-485 from previous unit Figure 19. Version 3.
TX3 System 3.5 Multiple Lobby Control Units Figure 20 shows a configuration of many Lobby Control Units to one phone line. The phone can be either a dedicated phone line from the phone company or an NSL phone line from the NSL Control Unit.
TX3 System 3.6 Networking TX3 Panels Mircom devices such as the Lobby Control Unit, the Card Access Controller, and the Touch Screen can be networked with the TX3 system through a peer-to-peer RS-485 network, an ethernet TCP/IP network, or a combination of ethernet and RS-485 networks. The TX3 Configurator software can connect to any of these network configurations.
TX3 System ethernet TCP/IP network. If you connect directly to one of the Master Nodes using USB, a modem, or a COM port, you will be able to configure that device but not any other device. Lobby Control Unit (Master Node) 1 4 GHI 7 2 ABC 5 JKL 8 Elevator Restriction Unit (Master Node) Card Access Controller (Master Node) Card Reader A 3 DEF 6 MNO 9 PQRS TUV WXYZ * 0 # Card Reader B Ethernet Network 42 (122) LT-969 Figure 22. TX3 devices on an ethernet TCP/IP network.
TX3 System Figure 23 shows a configuration with TX3 devices connected on both an ethernet TCP/IP network and on RS-485 subnetworks. Devices connected to a Master Node’s RS-485 subnetwork are Slave Nodes to the Master Node. Each RS-485 subnetwork can have up to 63 devices connected to it; you can still have more than 63 Master Nodes connected to the ethernet network.
TX3 System 3.7 Lobby Control Unit Wiring All units use the PS-4P transformer for the power supply. All wiring is a maximum length of 1000 ft. The door strike power supply depends on the door strike power requirements. Figure 24 shows a typical wiring arrangement for the Lobby Control Unit.
4 Lobby Control Unit Setup This chapter describes the Lobby Control Unit controller board components and provides information about its operation and setup This chapter explains Version 3.
Lobby Control Unit Setup 4.1 Controller Board Figure 25 shows the general layout of the Lobby Control Unit main controller board. See Figure 26 and Figure 30 for a detailed description of the connectors at the bottom and top of the controller board. Figure 25.Lobby Control Unit Main Controller Board 46 (122) LT-969 Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
Lobby Control Unit Setup 4.1.1 Connectors USB. Computer connection for firmware download and configuration. P4. TX3-MDM Modem Board connector. P5. MD-921 IP Module Board connector. P6. Key pad and front door LCD display. P7. Guard Phone Board connector. 4.1.2 Potentiometer PT1. Pulse phone potentiometer. This potentiometer is normally factory set and does not require adjustment. 4.1.3 Switches SW1. SW1 sets the unit’s RS-485 ID (node address) and the IP addressing mode. SW2.
Lobby Control Unit Setup 4.2 Controller Board Connectors - Bottom Figure 26 shows the connectors at the bottom of the controller board. Input 2 Input 3 Input 4 - + - + - + RS-485 OUT - s + - + Microphone Connection - + Input 5 - + Input 1 - + Speaker Connection LED/LAMP Supply - + Power Supply for TX3 (use 18 AWG) - + Camera Supply - s + RS-485 IN Figure 26.Controller Board Connectors - Bottom 4.2.
Lobby Control Unit Setup Inputs 1 to 5 are designated as follows (see Figure 26): Input 1. Postal Lock. Input 1 connects to the Postal Lock. Activation of this input unlocks the main door and starts the main door timer. The door locks when the timer expires or when the door sense input is activated. Daily usage is set as unlimited or limited. When set as limited daily usage is set according to a predefined number.
Lobby Control Unit Setup 4.2.4 RS-485 An RS-485 terminal lets you easily connect multiple telephone, card access and elevator restriction controllers across a network. The RS-485 connection is situated at the bottom middle of the main controller board and consists of two separate terminals, each for an input and output. See Figure 28.
Lobby Control Unit Setup 4.2.7 Power Supply The power supply connection is situated at the bottom right of the main controller board and receives 16 Vac, 40 VA. An external PS-4 or PS-4P plug-in transformer connects to the power terminals. Refer to Figure 26 and Figure 29. OFF ON ON/OFF Switch SW2 16 Vac IN 16 Vac Note: Use 18 AWG 120 Vac 16 Vac transformer (PS-4 or PS-4P) Figure 29. Power Supply Version 3.
Lobby Control Unit Setup 4.3 Controller Board Connectors - Top Figure 30 shows the connectors at the top of the controller board. Line 5 T R Line 1 T R Line 2 Line 3 T R T R AC Door Strike Line 4 T R DC Output 1 Door Strike General Relay Output 4 AC or DC Input Door Strike Supply NC C NO JW8 NC C NO Aux. Door Output 2 Relay Telephone Lines 1 to 5 General Relay Output 3 Figure 30.Controller Board Connectors - Top 4.3.
Lobby Control Unit Setup 4.3.3 AC or DC Input Door Strike Supply The power for the door strike is customer supplied and provides AC or DC power for one of the door strike outputs. Note: The controller is able to convert an AC supply to a DC output. The reverse is not true. Consequently, an AC door strike will not work with a DC power supply. The maximum supply for the AC or DC Input Door Strike is not to exceed: • 30 Vdc \ 3 amp • 30 Vac \ 1 amp 4.3.
Lobby Control Unit Setup 4.3.6 Auxiliary Door Relay The auxiliary door output is configured for activation by the resident’s telephone keypad and can be configured to activate general outputs. This relay is a relay contact programmable output with the same characteristics as a general output relay. 4.3.7 General Output Relays 3 and 4 Outputs 3 and 4 are relay contact programmable outputs with the following characteristics.
Lobby Control Unit Setup The TX3-MDM ribbon cable connects to the P4 connector on the controller board. MODEM MODULE RJ-11 connector Tip Ring Figure 32.Modem Module Telephone Connectors For a description on how to install the modem board see the Modem Manual Installation Instructions LT-971. 4.5 MD-921 IP Module The MD-921 IP Module connects the Lobby Control Unit to an ethernet TCP/IP network. The MD-921 IP Module ribbon cable connects to the P5 connector on the controller board (see Figure 25).
Lobby Control Unit Setup 4.6 MD-993 Module The MD-993 Module converts RS-485 signals to USB and is part of the TX3USB-AD Kit. The MD-993 Module ribbon cable connects to the P4 connector on the controller board. See Figure 25. The module has an RS-485 connector as shown in Figure 34. Figure 34.MD-993 Module For a description on how to install the MD-993 Module see the TX3-USB-AD Kit Installation Instructions LT-6027.
Lobby Control Unit Setup 4.7 Guard Phone Module The TX3-GPM Guard Phone Module mounts above the TX3 Lobby Control Unit main board on the top left hand side. See Figure 25. The module has two connectors, an RJ-11 connector and a ribbon cable as shown in Figure 35. The TX3-GPM ribbon cable connects to the P7 connector on the TX3 Lobby Control Unit main board. The guard phone uses a telephone cable to connect to the RJ-11 connector. RJ-11 Connector GPM Ribbon Cable Figure 35.
Lobby Control Unit Setup To receive a call from the Lobby Control Unit 1. When a visitor dials 9997 on the Lobby Control Unit the guard phone rings. Pick up the phone. The Lobby Control Unit is now connected to the guard phone. 2. Press the # key on the guard phone. The main door unlocks. To call a resident from the guard phone 4.9 1. Pick up the guard phone and wait for the dial tone. 2. Dial *DDDD (where DDDD is the resident’s four digit dial code). The resident phone rings.
Lobby Control Unit Setup Table 2 shows the SW1 DIP switch settings for each Lobby Control Unit. Table 2: Note: DIP switch 7 is not used and must be left at the default factory setting. Note: For units with and IP Module installed, DIP Switch 8 determines how the IP address is assigned to the IP Module. • DIP Switch 8 OFF: The IP address is assigned using a DHCP server. This is the default factory setting. • DIP switch 8 ON: The IP address is assigned using the TX3 Configurator software.
Lobby Control Unit Setup Table 2: Lobby Control Unit SW1 DIP Switch Settings Lobby Control Unit ID # Switch 1 Switch 2 Switch 3 Switch 4 Switch 5 Switch 6 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 60 (122) LT-969 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF
Lobby Control Unit Setup 4.10 Configuration Using a PC In order to correctly utilize the capabilities of the TX3 Telephone Access System you must first plan and establish how you want to configure the system for your application. The easiest way to configure the Lobby Control Unit is with the Mircom TX3MSW Configuration Software. This software is provided on a single CD-ROM or USB flash drive.
Lobby Control Unit Setup 4.11 Updating Firmware You can update the firmware on your panel with the TX3 Configurator software by using one of the following methods. • • Firmware Upgrade Wizard Network Firmware Upgrade The Firmware Upgrade Wizard can be used to update only one panel at a time. It will work on any panel. This method does not work on 64-bit versions of Windows. The Network Firmware Upgrade procedure can update more than one panel at the same time.
Lobby Control Unit Setup • LT-973 TX3 Configurator Quick Start Verify the following: • Ensure that the controller and all connected devices and components are fully operational. • Ensure the controller DIP Switches (SW1) are set with a unique network address. • Ensure the Configurator software is set with the correct controller network address. • Ensure that your PC and the Configurator are set with the correct date and time. To start the configuration Version 3.2 LT-969 1.
Lobby Control Unit Setup 64 (122) LT-969 Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
5 NSL Relay Cabinet Installation and Wiring This chapter provides information about the NSL Relay Cabinet Installation and Wiring. This chapter explains Version 3.
NSL Relay Cabinet Installation and Wiring 5.1 NSL Relay Cabinet Mechanical Installation The NSL Relay cabinets contain the telephone switching equipment and are typically mounted in the electrical/telephone room of a building.
NSL Relay Cabinet Installation and Wiring The top two mounting holes are 6 3/16 inches apart. Table 3: NSL Relay Cabinet Dimensions Model Number Dim ‘A’ Dim ‘B’ TX3-8EC 10 1/8” 13 15/16” TX3-NSL-8M 23 3/16” 27” TX3-16EC 23 3/16” 27” To mount the NSL Relay Cabinet 5.2 1. Using the back cover as a template mark the top two mounting hole locations 6 3/16 inches apart as shown in Figure 36. 2. Place the screws halfway into the wall in the position shown using a suitable screw. 3.
NSL Relay Cabinet Installation and Wiring Figure 37 shows a TX3-NSL-8M Relay Control Unit. NSL Backplane Board NSL Main Controller TX3-NSL-8M Relay Control Unit Figure 37. 5.2.2 TX3-NSL-8M Relay Control Unit 2012 NSL Relay The NSL Backplane board contains up to eight 2012 NSL Relay Boards. Each 2012 NSL Relay Board has 12 relays, allowing for a total of 96 relays. 5.2.
NSL Relay Cabinet Installation and Wiring The expanders allow a total of 16 backplanes to be installed, allowing for up to 1535 relays. Note: The TX3-NSL-8M and any TX3-8EC and/or TX3-16EC must all be adjacent to each other, mounted on the same wall and in the same room. Each slot accepts a 2012 NSL Relay Board TX3-NSL-8M NSL Unit Figure 38. Version 3.
NSL Relay Cabinet Installation and Wiring 5.3 Wiring the TX3-NSL-8M Main Controller Board The TX3-NSL-8M NSL Main Controller Board has both ribbon cable sockets and screw terminals. Attention: High voltages are present on this board during the ringing of suite telephones. Figure 39 shows the general layout of the TX3-NSL-8M Main Controller board components. Expansion Connectors P4 P6 P5 Res. Co.
NSL Relay Cabinet Installation and Wiring 5.3.2 Switches SW1. Turns the unit’s power ON and OFF for servicing, or to re-start the unit. SW2. Not used. 5.3.3 Jumpers JW1. JW1 is used for updating firmware and is normally open. JW2. JW2 is used for updating firmware and is normally open. All other jumpers are not used. 5.3.4 Telephone Line Each NSL control unit provides a single telephone line connection to the Lobby Control Unit. See Figure 40 and Figure 41.
NSL Relay Cabinet Installation and Wiring Relay control unit NSL SYSTEM Line Entry Control Panel Figure 40. NSL System with Telephone Line R Line 1 TX3-NSL-8M Relay Control Unit Line 5 T R Line 1 T R Line 2 Line 3 T R T R T Line 4 T R 5 1 2 3 4 TX3 Lobby Panel Main Controller Board Telephone Lines 1 to 5 Figure 41. 72 (122) LT-969 NSL Controller Telephone Lines Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
NSL Relay Cabinet Installation and Wiring To test the TX3-8M-NSL Relay Control unit 1. Connect a telephone to the TX3-8M-NSL Relay Control unit telephone terminal block (see Figure 39). 2. Pick up the telephone. A dial tone is heard. 3. Dial *RRRR#, where RRRR is the relay code. A resident line LED relay card light turns on. 4. Hang up. The resident line LED relay card light turns off. The TX3-8MNSL Relay Control unit is operational. 5. Perform the same test for all of the relay codes. Note: 6.
NSL Relay Cabinet Installation and Wiring 5.3.7 Connectors Up to 16 NSL backplanes connect to an NSL main controller board. Each has a set of 16 positions for a jumper plug. The first backplane is jumpered for “1", the next for “2", and so on up to “16". P1. Expansion from the previous controller or the NSL main controller board. P2. Expansion from the previous controller or the NSL main controller board. P3 to P10. Connectors for the 2012 NSL Relay Boards. (eight relay boards per backplane.) P11.
NSL Relay Cabinet Installation and Wiring 5.3.8 Using NSL with Phone Lines that Provide DSL Service If the building's telephone lines provide both DSL (digital subscriber line) and POT (plain old telephone) services then the ADSL-100 filter module is required to filter data signals. This filter module is installed between P4 on the NSL Controller board and P1 on the first Back Plane board that connects to it. Refer to the figure below for details on connecting the ADSL-100 module.
NSL Relay Cabinet Installation and Wiring 5.3.9 Setting the Backplane Number Relay addresses are numbered to show the relay card’s connector location and backplane number setting. Table 4 provides sample addresses for the first three backplane number jumper settings. For example, when the backplane number jumper setting is set to 1, the first relay on P3 relay board has an address of 1. When the backplane number setting is set to 2, the first relay on P3 relay board has an address of 97.
NSL Relay Cabinet Installation and Wiring Table 4: Sample Backplane Relay Addresses Connector Backplane Number Setting Jumper 1 Jumper 2 Jumper 3 Address 1-96 Address 97-192 Address 193-288 P3 1 to 12 97 to 108 193 to 204 P4 13 to 24 109 to 120 205 to 216 P5 25 to 36 121 to 132 217 to 228 P6 37 to 48 133 to 144 229 to 240 P7 49 to 60 145 to 156 241 to 252 P8 61 to 72 157 to 168 253 to 264 P9 73 to 84 169 to 180 265 to 276 P10 85 to 96 181 to 192 277 to 288 5.3.
NSL Relay Cabinet Installation and Wiring To connect the 2012 NSL Relay Board 78 (122) LT-969 1. Contact the telephone company at least three weeks before the actual installation to order the required blocks. 2. Complete the CA-71A or RJ-71C Block Identification Forms (Table 5 and Table 6) for the telephone installer. The form shows the telephone installer how the telephone lines connect to the BIX/Punch Down Blocks. 3.
NSL Relay Cabinet Installation and Wiring LEDs This connector mounts into the NSL backplane P1 P2 Figure 45. Version 3.
NSL Relay Cabinet Installation and Wiring Figure 46. 80 (122) LT-969 CA-71A BIX Block Wiring Configuration Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
NSL Relay Cabinet Installation and Wiring Table 5: CA-71A BIX Block Identification Form Relay Cabinet No. ____ of ____Decoder/Mother Board No.________ Relay Telephone Block Pins Apt. Dial Card/ Amp. Number Tel. Co./Res. # Code Jack # 1 2 Relay/ Relay Telephone Block Pins Apt. Dial Line # Card/ Amp. Number Tel. Co./Res.
NSL Relay Cabinet Installation and Wiring Table 5: CA-71A BIX Block Identification Form Relay Cabinet No. ____ of ____Decoder/Mother Board No.________ Relay Telephone Block Pins Apt. Dial Card/ Amp. Number Tel. Co./Res. # Code Jack # 3 4 82 (122) LT-969 Relay/ Relay Telephone Block Pins Apt. Dial Line # Card/ Amp. Number Tel. Co./Res.
NSL Relay Cabinet Installation and Wiring Figure 47. Version 3.
NSL Relay Cabinet Installation and Wiring Table 6: RJ-71C Punch-Down Block Identification Form Relay Cabinet No. ____ of ____Decoder/Mother Board No.________ Telephone Block Pins Apt. Dial Relay/ Relay Number Tel. Co./Res. # Code Line # Card/ Amp.
NSL Relay Cabinet Installation and Wiring Table 6: RJ-71C Punch-Down Block Identification Form Relay Cabinet No. ____ of ____Decoder/Mother Board No.________ Telephone Block Pins Apt. Dial Relay/ Relay Number Tel. Co./Res. # Code Line # Card/ Amp.
NSL Relay Cabinet Installation and Wiring 5.4 Updating Firmware After completion of the TX3-NSL-8M NSL Main Controller wiring and configuration, use the TX3-MSW Configuration Software to complete the firmware update. To update firmware 86 (122) LT-969 1. Turn the power OFF by using SW1 on the bottom right side of the card access controller board. 2. Short JW1 and JW2 using a jumper. 3. Turn the power ON. 4. Wait for 15 seconds. 5. Turn power OFF and remove jumper JW2. 6.
6 Elevator Restriction Unit Installation and Configuration This chapter provides information about the TX3-ER-8 and TX3-ER-8-A Elevator Restriction Unit models. This chapter explains Version 3.
Elevator Restriction Unit Installation and Configuration 6.1 Elevator Restriction Cabinet Mechanical Installation The Elevator Restriction cabinet contains the elevator access equipment and is typically mounted in the electrical/telephone room of a building. The unit is factory assembled in one cabinet size shown below. The back cover is 10 1/8 inches wide by 27 inches long. The top two mounting holes are 6 3/16 inches apart. Figure 48.
Elevator Restriction Unit Installation and Configuration To mount the Elevator Restriction Unit Cabinet 6.2 1. Using the back cover as a template mark the top two mounting hole locations 6 3/16 inches apart as shown in Figure 48. 2. Place the screws halfway into the wall in the position shown using a suitable screw. 3. Hang the box onto the two screws. 4. Screw the other two screws at the bottom of the panel. 5. Tighten all four screws into place.
Elevator Restriction Unit Installation and Configuration The elevator restriction unit consists of the main elevator restriction controller board and the elevator backplane. Up to eight 2012E Elevator Relay Boards may be installed, allowing for 96 elevator floors for access in this enclosure. See Figure 50. The Elevator Restriction Unit performs the following functions: • Provides time dependent relay contacts which can be used for either elevator or video control.
Elevator Restriction Unit Installation and Configuration 6.3 Wiring the Elevator Restriction Unit The Elevator Restriction Backplane use a ribbon cable to connect to the Elevator Restriction Main Controller board. The Elevator Restriction Controller has eight sockets for the 2012E Relay Boards. 6.3.1 Elevator Controller Board Figure 51 shows the general layout of the Elevator Controller board components. P4 P6 R T R Co. T P5 Res.
Elevator Restriction Unit Installation and Configuration 6.3.2 Connectors USB. Computer connection for firmware download. P1. Not normally used. Used for debugging purposes only. P2. Not used. P3. Connector for the MD-921 IP Module (for the TX3-ER-8-A model only). P4. Not used. P5. Expansion to the elevator restriction backplane. P6. Not used. 6.3.3 DIP Switches SW1. Turns the unit’s power ON and OFF for servicing, or to re-start the unit. SW2.
Elevator Restriction Unit Installation and Configuration 6.3.6 RS-485 Figure 52 shows the RS-485 elevator restriction unit wiring. USB Input Output - S + - S + 16 VAC IN PS-4P Transformer (located in electrical room) 18 AWG Twisted Shield Pair 18 AWG 18 AWG Daisy chain one to one connection (+ to +, S to S and - to -) to next RS-485 DO NOT T-TAP Twisted Shield Pair Figure 52.Elevator Restriction Controller Board Wiring Version 3.
Elevator Restriction Unit Installation and Configuration 6.4 Elevator Restriction Controller Backplane The Elevator Restriction Unit Backplane has ribbon cables to connect to the Elevator Restriction Main Controller board and eight sockets for 2012E Relay Boards. Position 8 Position 7 Position 6 Position 5 Position 4 Position 3 Position 2 Position 1 TX3-ER-8 Elevator Restriction Unit Figure 53.Elevator Restriction Controller Backplane 6.4.1 Connectors P1. Not used. P2.
Elevator Restriction Unit Installation and Configuration 6.5 2012E Elevator Restriction Relay Card The 2012E Elevator Restriction Relay Boards plug into the backplane portion of the Elevator Restriction Unit. They number from one to eight starting from the bottom slot and moving towards the top. Each relay board has 12 Form “A” or “B” relay contacts rated at 28 VDC, 0.5 amperes. Each jumper is selectable as normally open or normally closed.
Elevator Restriction Unit Installation and Configuration 6.6 Elevator Restriction Unit Configuration The Elevator Restriction Unit ID is set using the eight position DIP Switch labelled SW2 as shown in Figure 51. The individual switches are numbered 1 to 8 from left to right, and are marked as either ON or OFF. The first six switches (1, 2, 3, 4, 5 and 6) set the ID. Note: Table 7: Every Elevator Restriction Unit in a given TX3 System requires a unique ID. Unit IDs must not be duplicated.
Elevator Restriction Unit Installation and Configuration Table 7: Lobby Control Unit SW2 DIP Switch Settings Lobby Control Unit ID # Switch 1 Switch 2 Switch 3 Switch 4 Switch 5 Switch 6 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Version 3.
Elevator Restriction Unit Installation and Configuration 98 (122) LT-969 Note: DIP switch 7 is not used and must be left at the default factory setting. Note: For units with an MD-921 IP Module installed, DIP Switch 8 determines how the IP address is assigned to the IP Module. • DIP Switch 8 OFF: The IP address is assigned using a DHCP server. This is the default factory setting. • DIP switch 8 ON: The IP address is assigned using the TX3 Configurator software.
Elevator Restriction Unit Installation and Configuration 6.7 Updating Firmware You can update the firmware on your panel with the TX3 Configurator software by using one of the following methods. • • Firmware Upgrade Wizard Network Firmware Upgrade The Firmware Upgrade Wizard can be used to update only one panel at a time. It will work on any panel. This method does not work on 64-bit versions of Windows. The Network Firmware Upgrade procedure can update more than one panel at the same time.
Elevator Restriction Unit Installation and Configuration 100 (122) LT-969 Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
7 Adding Controllers This chapter provides information about adding additional controllers on the same network as the Telephone Access System. This chapter explains • Version 3.
Adding Controllers 7.1 Adding a Controller The TX3 telephone access system may be integrated with other controllers, such as the TX3-CX Card Access system and Elevator Restriction Unit, through a peer-to-peer connection via the RS-485 bus, an ethernet TPC/IP network, or a combination of RS-485 and ethernet networks. Connecting a controller to an RS-485 network requires that the controller have a unique ID address on the RS-485 network (valid addresses range from 1 to 63).
8 Appendix This chapter contains additional information about the TX3 Telephone Access System. This chapter explains Version 3.
Appendix 8.1 Specifications 8.1.1 Operating Temperature 50°C (122°F) to -20°C(-4°F). For temperatures where the Telephone Access System will operate below 0°C (32°F) at any time, install the TH-102K Thermostat Heater within the enclosure. 8.1.2 Telephone Lines Use only Loop Start telephones (not ground start), check with your local telephone company. 8.1.3 AC Power Supply 105 Vac to 128 Vac. Note: 8.1.4 Maximum power consumption for an 8-line by 20 character LCD TX3 Lobby Control Unit is 6.
Appendix 8.1.6 Post Office Lock The system has a built-in micro switch and mounting hardware for a postal lock installation. If a postal service is required, contact the Post Office to obtain the lock. 8.1.7 Tamper Switch This switch can be connected to any security or monitoring system to supervise the opening of the panel front door. This microswitch is the same type used for the postal lock.
Appendix 8.2 Kits - Electronic Scrolling Directory 8.2.1 TX3-120U and TX3-120U-A: Electronic Scrolling Directory plus Paper Directory Lobby Control Unit Kit 8.2.2 8.2.
Appendix 8.2.4 Version 3.
Appendix 8.3 Kits - Telephone Access Slim-line 8.3.1 TX3-200-4U and TX3-200-4U-A: Slim-Line Electronic Scrolling Directory Lobby Control Unit Kit 8.3.
Appendix 8.4 Kits - Continental Series Enclosures 8.4.1 TX3-120U and TX3-120U-A: Electronic Scrolling Directory plus Paper Directory Lobby Control Unit Kit 8.4.2 8.4.3 8.4.4 Version 3.
Appendix 8.4.5 8.4.6 8.4.
9 Resident Operating Instructions This chapter describes the Telephone Access System operating instructions for use by the resident. This chapter explains Version 3.
Resident Operating Instructions 9.1 NSL Resident Operating Instructions Mircom's state-of-the-art door entry system provides you and your guest with an increased level of confidence and security. The TX3 Telephone Access system operates with your existing telephone. Your guest dials your code number or selects your name by scrolling through the electronic directory on the Entry unit, causing your telephone to ring. Note: 9.1.
Resident Operating Instructions Pressing “9”, “6” or “4” automatically reconnects to the previously "on hold" caller. In a similar manner, you can answer an outside call while talking to the guest in the lobby. Note: 9.1.3 You will be disconnected if you attempt to place your guest "on hold". Keyless Entry Codes The keyless code is a confidential number assigned to each resident by the building administrator to let you open the front lobby door without using a key. To unlock the front door Version 3.
Resident Operating Instructions 9.2 ADC Resident Operating Instructions Mircom's state-of-the-art door entry system provides you and your guest with an increased level of confidence and security. The TX3 Telephone Access system operates with your existing telephone. Your guest simply dials your code number or selects your name by scrolling through the electronic directory on the Entry unit, causing your telephone to ring. Note: 9.2.
Warranty & Warning Information Limited Warranty Mircom Technologies Ltd. together with its subsidiaries and affiliates (collectively, the “Mircom Group of Companies”) warrants the original purchaser that for a period of two years from the date of manufacture, the product shall be free of defects in materials and workmanship under normal use.
• defects caused by failure to provide a suitable installation environment for the products; • damage caused by use of the products for purposes other than those for which it was designed; • damage from improper maintenance; • damage arising out of any other abuse, mishandling or improper application of the products. Warranty Procedure To obtain service under this warranty, please return the item(s) in question to the point of purchase.
Out of Warranty Repairs Mircom will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to Mircom must first obtain an authorization number. Mircom will not accept any shipment whatsoever for which prior authorization has not been obtained. Products which Mircom determines to be repairable will be repaired and returned.
Special Notices Product Model Number: TX3 AC REN (U.S.): 0.0B AC REN (CANADA): 0.0 Complies With Federal Communications Commission (FCC): • TIA-968-A Technical requirement for connection of equipment tot he telephone network.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alteration made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the earth ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.
on your telephone lines should be less than five in order to assure proper service from the telephone company. In some cases, a sum of five may not be useable on a given line. Changes to Telephone Service The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
Product Identifier This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the back of the front panel cover of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
(122) LT-969 Telephone Access System Installation and Operation Manual Copyright 2015 Version 3.
