GUIDE TO INSTALLATION AND OPERATION PRELIMINARY Safety Compliance Information Safety Compliance This equipment complies with: - CSA C22.2 No. 60950-1-03 / Safety of Information Technology Equipment, Including Electrical Business Equipment. st UL 60950-1 (1 Edition) / Safety of Information Technology Equipment, Including Electrical Business Equipment. st IEC 60950-1 (1 Edition) Incorporating A1, A2, A3, A4, and A11/ Safety of Information Technology Equipment, Including Electrical Business Equipment.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION Table of Contents 1 UVP-101i Universal Video Processor/Synchronizer................................................... 1 1.1 Introduction ...............................................................................................................................................1 1.2 Features ...................................................................................................................................................1 2 Installation .
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 4.5 Audio Processing Functions [MENU: ABUS→#1 and ABUS→#2] .......................................................15 4.5.1 Audio De-Embedding [MENU: ABUS→#1 (or #2)→DMUX]..........................................................16 4.5.2 Audio Embedding [MENU: ABUS→#1 (or #2)→MUX] ...................................................................16 4.5.3 VBIT Processing [MENU: ABUS→#1 (or #2)→VBIT].............................................................
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION 1 UVP-101i Universal Video Processor/Synchronizer 1.1 Introduction The UVP-101i is a universal video incoming feed processor supporting both digital and analog input standards, 20-bit AES embedded audio handling and both digital and analog standards available at the outputs. The analog input's adaptive decoder can handle a variety of decoding modes including Adaptive 2D, Adaptive 3D and Super Adaptive.
GUIDE TO INSTALLATION AND OPERATION • • • • • PRELIMINARY 12-bit video signal processing and 20-bit audio embedding / de-embedding EDH monitoring and insertion SDI outputs with embedding of up to 2 AES groups (8 channels) Composite outputs True PAL decoding 2 Installation 2.1 Unpacking Make sure the following items have been shipped with your UVP-101i. If any of the following items are missing, contact your distributor or Miranda Technologies Inc.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION Rear module switch settings: The switch locations on the Symphonie-R-M rear module are shown in Figure 2.1. - The reference switch LK1 is used to select the reference source for the imaging module. Selecting local (LK1 position 2-3) drives the reference signal, connected to the rear module, to the imaging module. - The reference signal selected by LK1 must be terminated by selecting ON (switch LK2 to position 2-3). Fig. 2.
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 2.2.3 Rear Panel Label Connector labels have been shipped with the UVP-101i. These labels are to be installed on the rear panel of the Quartet-M or Symphonie frame in order to identify the module’s external connectors. Quartet-M Frame To install the label on a Quartet-M frame, follow these steps while referring to Figure 2.2. Figure 2.2 Rear panel label installation on Quartet-M frame 1.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION 2.3 Signal Connections 2.3.1 Rear Panel Inputs and Outputs The UVP-101i has eight connectors on the rear panel of the frame. Seven of these are common to all installations. The other two differ according to the installation, as shown in the following figures and table. UVP-101i UNIVERSAL VIDEO PROCESSOR / SYNCHRONIZER 1 4:2:2 ININ COMP REF IN COMP IN 4:2:2 IN 2 DELAY/GPI 1 Delay GPI 2 COMP OUT 4:2:2 OUT Figure 2.
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 2.3.2 RJ-45 Connector The pinout of the RJ-45 connector on the rear panel is shown in figure 2.5. Pin 1 2 3 4 5 Signal Pin Signal GND GPI Error GND Tracking delay (+) Tracking delay (-) 6 7 8 9 10 Not connected (NC) NC NC NC NC Figure 2.5 RJ-45 connector pinout 2.3.3 Audio Bus Connector Layout Figure 2-1 The UVP-101i incorporates two audio bus connectors, located on the front card edge (see figure 3.1).
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION The UVP-101i detects the line format of the reference. A valid analog composite reference signal will turn on the REF indicator located on the module’s front end. The reference signal must be NTSC for 60 Hz sources (NTSC, 525) and PAL for 50 Hz sources (PAL, 625). If there exists a line format mismatch between the reference input and the composite input, the REF indicator flashes, but the output format is forced to black and set according to the reference.
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 3 Operation 3.1 User Controls Figure 3.1 below shows the card-edge user interface. FRONT-TOP VIEW Red Green Yellow Black Display ABUS #2 525 ERR REF 625 EDH B&W ABUS #1 ESC - FREEZE + TEST SELECT INPUT UVP-101i UNIVERSAL VIDEO PROCESSOR/SYNCHRONIZER 1 2 3 4 AUDIO IN DETECTED UVP-101i Figure 3.1 Card-edge user interface 3.1.1 LED Indicators The 525/625 LEDs (green) indicate the line format of the selected input video.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION 3.1.2 Push Buttons The following functions are accessible from the card-edge-mounted push buttons: TEST Enables and Disables the internal test signal on both analog and digital outputs. Toggles between 100% white bar and 75% Color Bars, black, and normal mode. When it is activated, the EDH error codes (flags) are blanked as well as the HANC and VANC intervals on the input side. FREEZE Enables and Disables the manual freeze mode (see section 4.7.1).
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY Figure 3.2 UVP-101i Menu Tree DISPLAY VALUES INP [ANA, SDI] ICMP (INP = ANA only) PROC TIMG FRMT SEL [AUTO, NTSC, PAL, B&W5, B&W6] SRC SEL [SAT, STUD, VCR] DECD SEL [SADP, A-3D, A-2D] (SRC = STUD or SAT only) SETP SEL [-10, ..., -0.1, 0, 0.1, .., 7.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION DISPLAY VALUES FRZE COMP NOTES MAN SEL [FLD1, FLD2, FRM] AUTO SEL [OFF, FLD, BLAK, BLK3] (not available with SRC = VCR or no REF IN) SETP SEL [0, 7.
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 4 Description of Operating Functions The operating functions of the UVP-101i are described in the following paragraphs. In all cases reference is made to the location in the menu where the described function can be controlled. The functions are presented in the order of their appearance in the menu tree. 4.1 Video Input Selection [MENU: INP] The UVP-101i supports two types of video input: composite analog (ANA) and serial digital (SDI).
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION Studio In this mode, the TBC is OFF and the AGC is OFF. If there is a valid external reference, the output phasing (V, H and fine H) is set with respect to the reference timing. If there is no reference, the output phasing is set with respect to the analog video input (frame buffer mode). VCR In this mode, the TBC is ON and the AGC is OFF.
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 4.3.7 Hue Adjustments (NTSC/525 only) [MENU: PROC→HUE] The hue can be adjusted from –180 to +180 degrees in steps of 1 degree in 525 and 1.4 degrees in NTSC. The default value is zero. 4.3.8 Horizontal Position (COMP IN only) [MENU: PROC→HPOS] Picture position may be adjusted by +/- 7 pixels (a total range of 518 ns) in steps of ½ pixel (37 ns). 4.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION phased with the reference or the input within less than +/- 18.5 ns. NOTE: fine phasing is only available when a reference input is detected. 4.5 Audio Processing Functions [MENU: ABUS→#1 and ABUS→#2] The UVP-101i does not possess on-board audio processing capability. However, it can disembed audio carried in the SDI input signal, and pass it to an external processor (such as Miranda’s UAP-712i or DAP712i).
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 4.5.1 Audio De-Embedding [MENU: ABUS→#1 (or #2)→DMUX] Audio De-Embedding from the digital input. Up to 2 Groups / 8 Channels are extracted and passed to a companion audio delay/processor card via the header connectors on the front of the module. 4.5.2 Audio Embedding [MENU: ABUS→#1 (or #2)→MUX] Audio embedding of up to 8 Channels (2 Groups) audio. Audio obtained from header connector linked to companion audio card.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION Table 4.1 Output when Manual Freeze is activated. Menu Option Output Display Field 1 (FLD1) Displays field 1 of the current frame. Field 2 (FLD2) Displays field 2 of the current frame Frame (FRM) Displays the current frame 4.7.2 Automatic Freeze [MENU: FRZE→AUTO] The conditions which generate an automatic freeze are shown in table 4.2.
GUIDE TO INSTALLATION AND OPERATION PRELIMINARY 4.8.3 Horizontal Blanking/Edge Control [MENU: COMP→HBLK] For the analog output only, the blanking interval can be NAR (narrow, as per SMPTE 259M : all pixels are passed) or WIDE (as per SMPTE-170M). 4.8.4 Closed Captioning [MENU: COMP→CC] The user can select whether closed captioning data from the incoming signal is inserted into the analog output (NTSC only). 4.8.5 Gain [MENU: COMP→GAIN] The overall level of the composite output signals can be adjusted.
PRELIMINARY GUIDE TO INSTALLATION AND OPERATION 5 Specifications ANALOG INPUT Signal: NTSC (525/60) SMPTE 170M PAL (625/50) ITU-R BT.740-6 Return loss: > 35 dB up to 5.75 MHz DIGITAL INPUT Signal: 4:2:2 SMPTE 259M-C (270 Mbps) Cable length: 250 m (850') Belden 8281 Return loss: > 15 dB up to 270 MHz REFERENCE INPUT External reference: SMPTE 170M/PAL ITU 624-4 or 2 Vp-p/ 4 Vp-p Composite Sync Return loss: > 35 dB up to 5.
GUIDE TO INSTALLATION AND OPERATION MISCELLANEOUS Audio embedding: SMPTE 272M, ABD Test signals: 75% color bars with 100% white bar; black Power: 12 W maximum 20 | UVP-101i PRELIMINARY
