User Guide Please Read This Instruction Manual Before Using Your Water Cooler Water Bottle Dispenser or Bottleless Dispenser oaisiscoolers.
Thank you for purchasing an Oasis Water Dispenser. This unique design offers the benefits of • No more struggling and lifting of heavy water bottles • No more accidental water spillage during water bottle installation • No more looking at bruised and battered recycled water bottles Please read the enclosed operating instructions carefully and retain this booklet for future reference. We have carefully engineered your Water Dispenser to give you years of enjoyment and trouble free operation.
WATER DISPENSER CONTROLS 1. Control panel 2. Heating 3. Ready-to-dispense indicator lights ™ Red Light: “Flashing” = Heater (hot water tank) is operational Red Light: “Steady On” = The hot water has reached optimum temperature and is ready for dispensing. Red Light: “Off” = Hot water tank heating system is off, however water within the tank may still be very hot. Always exercise caution when dispensing and/or draining water from the hot water tank.
OPERATING INSTRUCTIONS Initial Product Cleaning Procedure Like most appliances, your water dispenser requires periodic maintenance for maximum efficiency and performance and must be cleaned on a regular basis (i.e. every 4 months). To maintain a hygienic environment within your water dispenser and prevent potential formation (growth) of bacteria, we strongly recommend regular cleaning. 1. Make sure the lower compartment storage door is “open” (this will prevent activation of the water pump). 2.
Installing the Water Bottle The Mirage can use 3 or 5 gallon water bottles. This unit also easily converts to a direct water line. Please see page 7 for instructions on installing this unit direct to a water line and filtration system. IMPORTANT: Always wash your hands first before handling water bottle! Clean the top of the water bottle with a clean cloth. Water bottles can be purchased from your local retailer. 1. Make sure the lower door (bottle storage compartment) is open.
IMPORTANT: DO NOT BREAK OR REMOVE THE SEAL FROM AROUND THE NECK OF THE WATER BOTTLE, (See Fig. 5) OTHERWISE YOU WILL NOT BE ABLE TO LIFT/CARRY THE WATER BOTTLE WITH THE CARRY HANDLE. (See Fig. 6) 5. To install the water bottle inside the bottle storage compartment, simply position the bottle in front of storage compartment ramp and (push) slide inside using the side of your leg until the bottle comes to a stop. 6.
Converting to Direct Water Line (bottleless water option) 1. Your cooler comes set up for 3 gal. (11.4L) or 5 gal. (18.9L) bottle bottom load as shown in figure “A”. 2. Disconnect the bottle siphon from the door by pulling the handle away for the door, as shown by the arrow direction in figure “A” 3. Disconnect the water supply tube from the siphon cap elbow as shown if figure “B”, see instructions below A 4. After disconnecting the siphon, store in a safe place for future use.
6. Assemble the filter as per individual instructions. F - Filter set sold separately. F 7. The filter bracket has several hole patterns to accommodate different filter mounting configurations. It may be necessary to provide your own holes per your individual filter instructions. Note: Mounting screws are not included with your cooler. Oasis Green Filter Filter Bracket 8. Mount the filters to the filter bracket per individual instructions as show in figure G. Note.
10. Your cooler will come equipped with a supply tube bushing for the inlet tube to pass thru the rear of the cooler similar to the one shown in figure J. Push the supply tubing through this bushing to make your external supply water connection. Note: Observe all local and state plumbing codes. Supplied tube bushing 11. Your cooler is equipped with open door safety interlock system that will suspend all coolers functions while the access door is open.
CLEANING AND MAINTENANCE Like most appliances, your water dispenser requires periodic maintenance for maximum efficiency and performance and must be cleaned on a regular basis (i.e. every 4 months). To maintain a hygienic environment within your water dispenser and prevent potential formation (growth) of bacteria, we strongly recommend regular cleaning. Cleaning the Outside of the Water Dispenser The outside of the dispenser can be wiped clean with clean solution or a mild soap and water mixture.
Problem Possible Cause Suggested Solution Water dispenser is leaking Drain cap and silicone seal are not secure. Ensure seal is secure in drain plug and tighten cap. Water is not hot or cold enough All the water in the tank has been used. Replace with full bottle and wait 60 minutes for water to cool. The unit is unplugged. Plug into the outlet. The circuit breaker is tripped or a fuse is blown. Reset the breaker or replace the fuse. Temperature limit tripped.
222 Campus View Blvd, Columbus, Ohio 43235 800.646.2747 | cs@oasiscoolers.
