Specifications

54
55
IR Remote Control Codes/RJ12 Command CodesRJ12 Command Code Format
Command Codes for the RJ12 Connector/IR Remote Control
Codes – NEC Protocol – Address 00FF
Function Hex Code
Power ON
D827
Power Toggle ON/OFF (see note)
1CE3
DTV
E817
ATV
E718
SCART
EA1 5
Component
E619
PC – RGB
E916
HDMI
EB1 4
Composite
EC1 3
S-Video
E51A
Input
17E8
Channel 1
54AB
Channel 2
16E9
Channel 3
15EA
Channel 4
50AF
Channel 5
12ED
Channel 6
11EE
Channel 7
4CB3
Channel 8
0EF1
Channel 9
0DF2
Channel 0
0CF3
CH + Channel Up
09F6
CH – Channel Down
05FA
Vol + Volume Up
4BB4
Vol – Volume Down
4FB0
Mute
08F7
Menu
18E7
U Navigation Up
1AE5
D Navigation Down
48B7
L Navigation Left
47B8
R Navigation Right
07F8
Enter/OK
06F9
Exit
0AF5
EPG
40BF
Red (Fast Text)
5DA2
Green (Fast Text)
59A6
Yellow (Fast Text)
51AE
Blue (Fast Text)
55AA
Fav (Favourites)
58A7
Info (Information)
5CA3
Pic (Picture Mode)
4EB1
Sound (Sound Mode)
4AB5
Aspect (Aspect Ratio)
02FD
Return (PLP/Previous Channel)
49B6
Audio
53AC
Subtitle
57A8
Sleep
1EE1
Tex t
03FC
Index (Text)
56A9
List (Text)
52AD
Hold (Text)
5AA5
Size (Text)
5BA4
Reveal (Text)
5EA1
Subpage (Text)
5FA0
TV/Radio (DTV only)
10EF
Nicam (ATV only)
14EB
To program an IR remote control to
transmit a signal to operate the
Mirage the codes in the table (left)
must be entered.
Note:
There is no discrete Power Off
code, the Power Toggle On/Of must
be used to set the Mirage to
standby.
Power Toggle On/Off will set the
opposite condition of the Mirage as
below.
Mirage On – Power Toggle On/Off
– Mirage set to Standby.
Mirage Off – Power Toggle On/Off
– Mirage set to On.
Command Codes via the RJ12 Connector –
NEC Protocol.
The codes in the table on page 55 are the codes that will be sent to
the Mirage via the RJ12 connector.
The voltage levels that are accepted as an input on pin 2 of the
RJ12 connector (command code from external equipment to the
Mirage) are:
HIGH + 5 VDC LOW 0 V
Important: When the input on pin 2 of the RJ12 connector is
inactive/idle it must be held HIGH. If pin 2 of the RJ12 connector is
held low, all subsequent command codes via the RJ12 connector
and via the Mirage IR receiver (sent from the Mirage IR remote
control) will fail and the Mirage will be non responsive.
Pin 5 of the RJ12 connector is DC ground.
The command codes in the table below are written in the NEC
protocol format. Care must be taken when generating the command
code. The command codes are written as MSB (Most Significant
Bit), LSB (Least Significant Bit). The codes when delivered to the
Mirage must be LSB, MSB.
For the command codes in the table below to work correctly the
format of the NEC protocol must be INVERTED.
Logic 1 – 2.25 ms
Inactive/idle
HIGH
Inactive/idle
HIGH
Logic 0 – 1.12 ms
Address
0 0 F F
Code
8 D 7 2
Stop 560 µs
9 ms 4.5 ms
560 µs
The address is 00FF (hex). An example of the ‘Power On’ command
code written in the table – Power On = 00FFD827
An example of the ‘Power On’ command code delivered to the
Mirage via the RJ12 connector – Power On = 00FF8D72 – LSB first.
☛
Check www.tilevision.tv for updated information.