Technical Specifications

M A T E R I A L S A F E T Y D A T A S H E E T
Water Ring & Etch Remover
02 - 2012
Osha’s Hazard Communication Standard
U.S. Department Of Labor
Identity No:
Name: Water Ring & Etch Remover
Section 1
Manufacturers Name: Miracle Sealants Company
Address: 12318 Lower Azusa Road
Emergency Phone: [phone]
C
ity: Arcadia
State: CA
Phone: [phone]
Date Prepared:
02 - 2012
Section 2 - Hazardous Ingredient/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV
Potassium Oxalate 6487-48-5Not AvailableNot Available
Ammonium Bifluoride 1341-49-7 Not AvailableNot Available
Acrylic Acid 79-10-7 10ppm Not Available
VOC: 0% by weight (non-regulated)
Section 3 - Physical/Chemical Characteristics
Boiling point: (3) 141
0
C Freezing point: Not Available
Melting point: Not tested Vapor pressure: (3) 4
Vapor density: (3) 2.5 % Volatile: Not Available
Density: Not Available Odor threshold: Not
Available
Evaporation rate: Not Available Acid/Alkalinity: Not Available
Solubility in organic solvent: Not Available pH: Not Available
Solubility in water: (1) 25% in weight at 18
0
C - (2) 45.3% - (3) Complete
Physical State: (1) Fine, granular, white, odorless crystals.
(2) White, transparent solid. Slight acid odor.
(3) Colorless liquid, Sharply acrid odor.
Specific Gravity: (1) 2.13 - (2) 1.5 - (3) 1.05
Section 4 - Fire and Explosion Hazard Data
Flash point (method used): (3) 50 T.C.C. Flammable limits: Not
Available
LEL: 2 UEL: 8 DOT#: None
Extinguishing media: Water fog, CO2, alcohol or dry chemical
NFPA hazard rating - H F R S (0 - Least, 4 - Extreme: 2 0 0 0
Special fire fighting procedures: Not Available
Unusual fire & explosion hazard: Not Available
Section 5 - Reactivity Data
Stability: (1) and (3) Stable. (2) Unstable.
Conditions to avoid: (2) Heat and any open flame.
Incompatible materials to avoid: Strong oxidizers, acids and alkalis, aldehy-
des, ethers and amines.
Hazardous polymerization: May occur.
Conditions to avoid: Excessive heat and freezing.
Hazardous decomposition products: (2) nh3 and hf, which are corrosive.
Section 6 - Health Hazard Data
Routes of Entry:
Inhalation - Possible Skin - Possible Ingestion - Possible
Health hazards - Same as signs and symptoms of overexposure.
OSHA Carcinogenicity - None; - NTP - None; - IARC Monographs - None
Signs and Symptoms of Over Exposure:
Eyes: Material is ocular irritant & may cause cornea damage. Healing is usu-
ally complete if first aid measures have been promptly initiated.
Skin: may cause irritation to skin.
Ingestion: may cause systemic poisoning and cause severe damage to the
esophagus and stomach. May cause hypocalcemia, possibly fatal.
Inhalation: Irritation, may cause coughing & difficult breathing. Excessive
inhalation may cause systemic poisoning.
Medical conditions aggravated: Hypocalcemia, liver or kidney diseases.
Signs and symptoms of over exposure: Pain in throat, esophagus and stom-
ach.
Emergency and First Aid Procedures:
Eyes: Promptly flush plenty of water, lifting eyelids occasionally to facilitate
irrigation. Continue for at least 15 minutes.
Skin: Wash with plenty of soap and water. Then flush with water. Remove
clothing upon contamination and wash before reuse.
Ingestion: do not induce vomiting. Get prompt medical attention. Speed is
essential.
Inhalation: remove victim to fresh air. If exposure to dust or mist was
severe, get medical attention.
Section 7 - Precautions For Safe Handling And Use
Steps to be taken in case material is released or spilled: Promptly sweep or
shovel material into an empty container, avoiding dusty conditions. Label
container “poison” & close for later use or disposal. Complete clean-up by
flushing residue with plenty of water, skin and eye protection should be
used.
Waste disposal method: If permitted by applicable disposal regulations,
dispose of waste product via a secure solid waste landfill or dissolve in
large quantity of water and discharge to sewer, stepwise if necessary.
Precautions to be taken in handling and storing: Store in a cool, dry place,
away from food or feed products. Wash thoroughly after handling. Do not
get in eyes, skin, clothing. Keep container closed. Do not ingest.
Other precautions: KEEP OUT OF REACH OF CHILDREN. Follow directions on
the container for proper use of this product.
Section 8 - Control Measures
Respiratory protection: Ventilate by opening all doors and windows. If
exposure above the TLV or PELrequire a NIOSH approved respirator
equipped for the exposure or suitable respiratory protection per
29 CFR 1910.134 is required.
Protective gloves: Plastic or rubber chemical resistant.
Eye protection: Tight fitting, splash proof safety glasses or goggles.
Other protective Clothing or equipment: chemical resistant clothing.
Work hygienic practices: Wash hands thoroughly before handling food
stuffs, liquids or tobacco products. Use common sense and care around
chemicals. Never mix this product with other chemicals. Consult your super-
visor for all other hygienic and safety practices. All practices depend on
your specific business. Directions for use normally found on label which will
dictate engineering and control measures.
Section 9 - Shipping & Regulatory Classification
DOT Shipping Name: Please refer to the Bill of Lading receiving/documents
for up-to-date information.
DOT Hazard Class: Not Available
Toxic Substances Control Act (TSCA): This product and/or all the ingredients
contained in this product have been registered under the Toxic Substances
Control Act.
SARA: No SARA 313 chemicals identified.
NOTE: Miracle Sealants believes the data set forth are accurate. Miracle
Sealants makes no warranty with respects thereto and disclaims all liability
or reliance thereon. Such data are offered solely for consideration, investi-
gation and verification. Also, the data set forth is for the concentrated fin-
ished product.All lab samples are for experimental purposes only and used
at the customers discretion.
www.miraclesealants.com