Installation Instructions

12318 Lower Azusa Road, Arcadia, California 91006
1-626-443-6433
TILE SPACING &
LEVELING SYSTEM
PARTS SOLD SEPARATELY
Straight Grid / Pattern
+ Cross Spacer T Tee Spacer
Brick Grid / Pattern
50 per Bag
Coverage
Use one Flat Spacer for each grout joint along perimeter/wall.
Part
A
50 PER PACK
1/8in (3.175mm)
Visit
www.miraclesealants.com/levolution
to view product video
Universal Spacer/Anchor STEP 1 STEP 2
STEP 3 STEP 4 STEP 5 - WALLS
STEP 5 - FLOORS STEP 6 WALLS
On softer Natural Stones
& Tiles use Evolver Tool
ONLY to remove
Caps & Spacers
UNIVERSAL SPACER - 3 PROFILE OPTIONS
Exclusively distributed by
FLAT SPACER
CAPS DECAPPEREVOLVER TOOL
CROSS SPACER TEE SPACER
C D
B
A
UNIVERSAL SPACER
12 x 24 in (305 x 610 mm) = .75 per tile or 132 ft
2
16 x 16 in (406 x 406 mm) = .75 per tile or 117.28 ft
2
18 x 18 in (457 x 457 mm) = .75 per tile or 148.5 ft
2
8 x 48 in (203 x 1219 mm) = 1.44 per tile or 91 ft
2
12 x 24 in (305 x 610 mm) = 1.44 per tile or 68 ft
2
6 x 24 in (152 x 610 mm) = 1.44 per tile or 34 ft
2
The Universal Spacer/Anchor can be formed into a Cross profile (+) for straight grid patterns, a Tee profile (T) for brick grid
patterns or a Flat profile (-) for edges at walls for all patterns. The Spacer/Anchor comes in the Cross profile. To adjust to another
pr
ofile simply break off the small tab close to the base on either side (as shown in diagram). Removal of 1 tab will give you a Tee
Spacer, removal of both tabs will give you a Flat Spacer.
STEP 1 Spread adhesive using a 1/2in (12.7mm) notch trowel.
STEP 2 Lay tiles and insert appropriate size (1/8”, 3/16” or 1/16”) Universal Spacer/Anchor removing the appropriate tab
in order to get a Cross profile, a Tee profile or a Flat profile. Refer to paragraph one on how to adjust the Universal Spacer
into different profiles.
STEP 3 After Spacers/Anchors are installed, place Caps over the Spacer/Anchor firmly.
STEP 4 Slide the Evolver Tool onto the Spacer/Anchor and pull trigger to apply tension between the Cap and tile until the Cap
is firmly holding tile. The tension knob at rear of gun can be turned clockwise to decrease tension or counter clockwise to
increase tension. This is adjustable so you can adjust for various thicknesses of tile or stone.
LET TILES FULLY SET/CURE (Per Manufacturer’s Setting Material Instructions)
STEP 5 REMOVING REUSABLE CAPS & DIPOSABLE SPACER/ANCHOR
WALLS To remove Caps and Spacer/Anchor after tiles have fully set & cured, wind adjuster knob counter clockwise
on the Evolver Tool to adjust to maximum tension. Place Evolver Tool back on Spacer/Anchor and pull trigger
until Spacer/Anchor breaks off to fully remove.
FLOORS Spacer/Anchor can be kicked (parallel to the spacer) to break off in order to save time. Once Spacer is
broken off Caps can be removed with the Decapper Tool for reuse.
On softer Natural Stones & Tiles use Evolver Tool only to remove Caps and Spacer/Anchor as explained above for walls.
STEP 6 To reuse Cap, insert Decapper Tool and place tapered end (tip) between the Cap and strap/anchor to loosen teeth.
Slide the center slot through the Spacer/Anchor and hook under cap. Push down with thumb while supporting the Cap
with index finger and slide Cap upwards removing the Cap from the Spacer/Anchor. Discard the disposable Spacer/Anchor
and keep Cap for reuse.
WALLS Always place Spacer/Anchor in a vertical position (cross as shown in diagram) or horizontal
position (tee or flat) to avoid chipping tiles when removing.