Technical Specifications

P R O DU C T D AT A S H E ET
www.miraclesealants.com
511 H20 Plus
02 - 2011
Water & Stain Protection For
n
Grout
n
Quarry Tile
n
Ceramic Tile
n
Glazed Tile
n
Granite
n
Marble
n
Limestone
n
Terrazzo
n
Saltillo Tile
n
Slate
n
Flagstone
n
Concrete
n
Brick
n
Travertine
n
Porcelain Tile
Uses
n
Kitchens
n
Bathrooms
n
Showers
n
Health
n
Driveways
n
Patios
n
Garages
n
Facilities
Special Features
n
Easy-to-Use
n
Interior & Exterior Use
n
Oil Resistant
n
Retains Natural Color
n
Odorless
n
Non Flammable
NO PERFLUOROCTANE SULFONATE (PFOS); NO PERFLUOROCTANOIC ACID (PFOA)
PRODUCT DE SCRIPTION
KEEP OUT OF REACH OF CHILDREN. 511 H2O Plus is a unique water base formula-
tion designed for the protection of all surfaces where a water base product is
required. 511 H2O Plus penetrates into the surface and forms an invisible barrier that
is resistant to moisture and stains, while allowing vapor to escape. 511 H2O Plusis
not a surface coating and will not alter the natural look. 511 H2O Plus can be used on
interior and exterior applications. NO (PFOS) or (PFOA)
Test Data
Independent laboratory tests show 511 H2O Plus out performs competitive products.
Test results are available upon request for staining.
NOTE: For any questions concerning grout-refer to the grout manufacturers specifica-
tions. 511 H2O Pluswill not stop acid etching.
Slip Resistance
511 H2O Plus increases the static coefficient of friction on all surfaces. 511 H2O Plus
has been used successfully for compliance with the American Disability Act’s recom-
mendations for slip resistance (ASTM C 1028-89) on polished & honed surfaces.
Sample Testing
Due to the differences of each material, several inconspicuous test patches should
be completed to assure maximum performance. User must determine suitability of
the product for their intended use.
Protect Neighboring Surfaces
Always protect neighboring surfaces including wood, carpet, metal, landscaping and
other non masonry surfaces.
NEW INSTALLATIONS - APPLIC ATION INSTRUCTIONS
Read entire label and PDS/MSDS before using. This product should be
used directly from container and is not under any circumstances to be
thinned or diluted with anything before use.
Sealing As a Grout Release
Apply 511 H2O Plus to all surfaces prior to grouting. This step will allow quick and
easy cleanup after grouting. Grout can stain many surfaces if this procedure is not
used prior to the grouting process. Apply 511 H2O Plus using a Mira Brush or a clean
towel. Apply enough to wet the surface. Be careful not to saturate the open grout
joints. Allow 511 H2O Plus to stand for approximately 3 - 5 minutes for maximum
penetration. All excess must be removed at this time by buffing surface with a clean
dry towel. This is very important on polished, glazed surfaces, and porcelain surfaces.
Allow 511 H2O Plus to cure for 6 - 12 hours before continuing with the grouting proce-
dure.
After Grouting: Once grouted, make sure that all grout residue is removed from the
surface with a clean sponge and water. Allow grout to dry at least 24 - 72 hours. If
grout clean up is not performed effectively, an additional cleaning may be necessary
to remove remaining grout residue or haze. For this procedure use Phosphoric Acid
Cleaner , GCFR (Grout, Concrete & Film Remover) or Epoxy Grout Film Removeras
directed.
Grout Sealing
Once the area has completely dried, proceed with the sealing of the grout for water
and stain resistance. Apply 511 H2O Plus to all grout with a thin paintbrush. Any
excess sealer that gets on the surface should be wiped off with a clean towel before
it dries.On larger jobs, grout can be sealed by retreating the entire area including the
tile or stone surface a second time. Be careful not to allow sealer to puddle or dry on
presealed surfaces.
Existing Installations - Surface Preparations
Surface must be dry and free of contaminants, including previously applied sealers,
dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime.
Floor Coating/Wax Removal: To remove existing coatings and/or waxes, use Mira
Strip or H2O Strip per the instructions.
Heavy Duty Cleaning: To remove lime and hard water deposits, efflorescence, rust,
grease and other heavy dirt and grime use GCFR (Grout & Concrete Film Remover),
Phosphoric Acid Cleaner as directed. For a non-acid deep clean use Liquid Poultice
as directed.
Light Duty Cleaning: Use Mira Clean #1, Porcelain & Ceramic Tile Cleaner, Counter
Kleen, or Mira Soap as directed.
Color & Gloss Enhancement
For color and gloss enhancement, use 511 Seal & Enhance, Mira Matte or Mira
Shine as directed.
Existing Installations - Application Instructions:
Follow the application instructions previously mentioned, except now, seal the grout
and tile or stone surface at the same time. When treating surfaces together, make
sure that the recessed grout is saturated with sealer.
Cure Time
511 H2O Plus will be dry to the touch in 1 - 3 hours and may be put into service. For
optimum results the area should be kept dry and free from staining materials for 24 -
72 hours.
Coverage
Coverage will vary depending on the density, porosity, texture, surface absorption,
weather, time solution left on surface and application methods. Used as directed, 511
H2O Plus will cover between 500 - 3,000 sq.ft. per gallon (45 - 270 square meters per
3.785 liters).
MAINTENANCE
For ongoing maintenance instructions please refer to Miracle Sealants Care Guide.
Refer to the Miracle Sealants Product Recommendation Chart for specific product
recommendations.
Storage
Store 511 H2O Plus in the original container, properly sealed to avoid contamination
and evaporation. Stored at 77° F (25° C), 511 H2O Plus will have a shelf life of 12
months. Do not allow to freeze.
Technical Support
For additional technical support, contact Miracle Sealants Company at
1-800-350-1901 or 626-443-6433 ext. 3013
Office Hours
Monday - Friday from 8:30 am - 5:00 pm PT.
1-626-443-6433 or 1-800-350-1901 • Fax: [phone]
website: www.miraclesealants.com
Product Damaged During Transportation
If product is damaged during transportation contact Info Trac @ 1-800-535-5053
Warranty
Instructions are a condensed guide and should not be considered complete. In the
event of failure, the only obligation of Miracle Sealants Company shall be to replace
such products proven to be defective. Before using, user shall determine the suit-
ability of the product for their intended use User assumes all risks and liability
whatsoever in connection therein. Neither seller nor manufacturer shall be liable for
any injury or inability to use this product.
Caution
Warning: Detectable amounts of chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm may be found in this product.
511 H2O may cause irritation of eyes and skin. Avoid contact and prolonged breath-
ing. Use in a well ventilated area. Good ventilation means that fresh air is flowing in
such a way as to feel a slight breeze. Open windows and use fans to circulate air.
Continue to ventilate until vapors are eliminated. Exposure to high vapor concentra-
tion must be avoided. Inhaling the vapors can be harmful. Keep away from heat and
open flames. Avoid prolonged contact with skin. Chemical resistant gloves should be
worn at all times. Keep small children and pets out of area until product or surfaces
has thoroughly dried. Refer to the MSDS for additional information.
Additional Products
Miracle Sealants Company offers a complete line of water & stain repellents, sealers,
cleaner, polishing compounds, diamond abrasives, machinery and accessories for
the tile, stone, concrete, metal, fabric and carpet professional or do-it yourself spe-
cialist.