MI-808T Stereo Transmitter User Guide MIPRO Electronics Co., Ltd. Headquarters: 814 Pei-Kang Road, Chiayi, 60096, Taiwan. Web: www.mipro.com.tw E-mail: mipro@mipro.com.
WARNING ! IMPORTANT SAFETY INSTRUCTIONS ! 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Contents Stereo Transmitter 1. Preface: 1 This system is engineered to meet the stringent requirements demanded in a variety of pro audio applications, such as by musicians, performers and directors. 2. Features of the MI-808T 2 To get the most out of your system, please read this manual thoroughly. 3. Glossary 3-4 1. Preface Characteristic of the MI-808T: 4. Operating the MI-808T 5-11 5.
Stereo Transmitter Stereo Transmitter 3. Glossary: 2. Features of MI-808T: The MI-808T is a UHF-band stereo transmitter. In each 24 MHz bandwidth there are 16 pre-programmed, user selectable non-interfering frequencies available. The MI-808T employs the latest high-efficiency transmitting circuitry and includes a rugged metal casing which combine to make it the right choice for audio professionals. Front Panel: 8 L R LIM POWER HEADPHONE VOLUME -12 CH 04 -20 -30 FREQUENCY 81 1 .
Stereo Transmitter Stereo Transmitter 4. Operating the MI-808T: Rear Panel: 1. Installation of the Antenna Coaxial cables may be used to remotely locate the transmitting antenna. ANTENNA 9 LOOP OUT L R AF IN (L) AF IN (R) MONO DC IN (12~15V) 10 11 12 13 14 (Figure 2) 2. Installation of Front Mounted Antenna 9 Transmitter Output Connector: Antenna connection. Use an accessory FB-71 rack mount kit. For best results, locate the antennas on the front panel.
Stereo Transmitter Stereo Transmitter 4. Installation of Power Supply 8. Transmission Frequency Set Up Connect the DC 12V~15V/1A power supply to the power input socket. The power supply cable may be fastened to the rear panel to prevent the plug from dislodging. a) Press the up/down key. The LCD display will show the preset frequency. b) Press the left/right key and the LCD display will start blinking. c) Press the left/right key to select desired frequency. 5.
Stereo Transmitter Stereo Transmitter 10. Setting the Input Sensitivity 11. Setting a Name a) Press the up/down key to display Input Sensitvity. a) Press the up/down function key to display NAME on LCD display. b) Press the left/right key. The display will start blinking. b) Press the left/right function key and the display will start blinking. c) Press the left function key (-), the second row on the display will show LOW meaning low input sensitivity.
Stereo Transmitter Stereo Transmitter 13. Using the Monitor Feature and Connecting Headphones 14. Rack Installation of Duial MI-808T's a) Single, half-rack transmitter Plug a stereo headphone into the headphone output socket 2 and use the volume control to adjust the volume to suit. Note that the connector must be a stereo plug. Screw the rack mount ears on left and right sides. Please see the illustration below for correct assembly.
Stereo Transmitter Stereo Transmitter 5. Important Notes: 1. To avoid interference, monitoring systems and wireless microphone systems should not operate simultaneously using the same frequency band. 2. Use only 50Ù coaxial cable to connect the transmitters to external antennas and keep the cable length to less than 5 meters. 3. For best results, maintain line-of-sight between the transmitters and their matching receivers. 4. When using a DC power supply, please be aware of the operating voltage.
