Home Products Support SHOP Blog Contact Explore Splash User Manual Content: 1. Content of the Package 2. Power and Operation 3. First Use 4. Camera and Flash Connection 5. Mobile Application 6. Connecting to MIOPS Splash 7. Firmware Upgrade 8. Using the Mobile Application 9. DEVICE SETUP 9.1 1st Drop 9.2 2nd Drop 9.3 3rd Drop 9.4 4th Drop 9.5 Trigger 10. Example Setup 11. SETTINGS 1.
1 x Splash Holder 2. Power and Operation Home Products Support SHOP Blog Contact Explore There are two types MIOPS Splash and the old version works with battery but the new version works from a USB power source. New Version: Your MIOPS Splash comes with Micro USB power cable so you can attach it to any USB power source to turn it on. Old Version: MIOPS Splash operates with a single 23A (12V Alkaline) battery. It is important that you use a compatible battery only.
2.5 mm stereo female jack. The camera cables have the male 2.5 mm stereo jack on one end. This end is plugged into the camera connection port. The other end changes depending on the camera make and model. This end is plugged in the shutter release port of your camera. The ash cable port is a 3.5 mm stereo female jack. There is only one type of ash connection cable. SHOP Contact It has aHome 3.5 mm Products male jack one end. This end isBlog plugged into the Explore ash connection port.
Home Products Support SHOP Blog Contact Explore 7. Firmware Upgrade MIOPS Splash has the capability of updating its rmware without needing any cable connection to a computer. You can use the mobile app to check for new rmware version and then update the device with a single click. When you connect your device through MIOPS MOBILE app, it automatically checks your device's rmware version and prompts a pop-up message if a new rmware is available.
Home Products Support SHOP Blog Contact Explore When you click the "Update" button: If you have a 1st generation MIOPS Splash: You will be asked to put your device to upgrade mode. In order to put your device to upgrade mode, you should turn your device o , then turn it back on while holding down the valve button on the left side of the device. After clicking to the Ready button, the rmware upgrade process will start immediately.
Home Products Support SHOP Blog Contact Explore You can also use the "Check Firmware Update" option in the Settings menu to check manually if there is a new rmware available.
Home Products Support SHOP Blog Contact Explore 8. Using the Mobile Application The mobile app has a main screen to change the settings of your water drop setup. You can see all of the parameters on this screen. When you connect your MIOPS Splash through the MIOPS MOBILE app, your device will stop blinking and you will notice a Bluetooth icon with a green tick on the top left-hand side of the app screen. This shows that you connected your device successfully.
Home Products Support SHOP Blog Contact Explore 9. DEVICE SETUP This screen is used to set parameters for your water drop photography setup.
Home Products Support SHOP Blog Contact Explore 9.1. 1st Drop: This screen is used to set the rst drop. It has a single parameter. Drop Size: This parameter is used to set the size of the drop. The unit is in milliseconds. So if you set the drop size to 50, the valve will be open for 50 milliseconds. Drop size cannot be zero for the rst drop as a single drop is a minimum requirement for the water drop photography. 9.2. 2nd Drop: This screen is used to set the second drop if needed.
Delay: This parameter is used to de ne the delay between the second drop and the rst drop. The unit is in milliseconds. For example, if you set the delay to 120, the second drop will be released 120 milliseconds later than the rst drop. Home Blog Explore You can set theProducts drop size zero if you SHOP don't want to dripContact the second drop. to Support 9.3. 3rd Drop: This screen is used to set the third drop if needed. It has two parameters.
camera will be triggered 100 milliseconds later than the last drop. Trigger Mode: This parameter is used to de ne which output will be triggered after the last drop. You can select one of the two possible modes. The modes are the “Flash” and the “Camera”. In the “Camera” mode, it will trigger the camera after dripping the drop(s).
11. SETTINGS: You can use the Settings menu to change application related or device related settings or to get information. Home Products Support SHOP Blog Contact Explore Serial Number: This parameter shows the serial number of your device. Check Firmware Upgrade: This button is used to check if there is a rmware available. Pulse Length: This parameter is used to determine the pulse length of each trigger signal for the camera and the ash.
Home Products Support SHOP Blog Contact Explore Newsletter Join us! Start learning and discover photography! your@email.
A liate Shipping Vimeo Policy YouTube Refund Home Products Policy Support SHOP Blog Contact Explore Terms of Service MIOPS Copyright © 2020 All rights reserved
