SAFETY DATA SHEET 330 Section 1. Identification Product name Product code Other means of identification : MINWAX® POLYSHADES® Interior Stain & Polyurethane Satin Finish Olde Maple : 330 : Not available. Product type : Liquid. Relevant identified uses of the substance or mixture and uses advised against Not applicable.
Section 2. Hazards identification General Prevention Response Storage Disposal Supplemental label elements Hazards not otherwise classified : Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. : Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use explosionproof electrical, ventilating, lighting and all material-handling equipment.
Section 4. First aid measures Description of necessary first aid measures Eye contact Inhalation Skin contact Ingestion : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention following exposure or if feeling unwell. : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Section 4. First aid measures Specific treatments : No specific treatment. Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.
Section 6. Accidental release measures Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g.
Section 8. Exposure controls/personal protection Appropriate engineering controls Environmental exposure controls : Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Section 9. Physical and chemical properties Flammability (solid, gas) : Not available. Lower and upper explosive (flammable) limits : Lower: 1% Upper: 7% Vapor pressure Vapor density Relative density : 0.023 kPa (0.169 mm Hg) [at 20°C] : 5 [Air = 1] : 0.92 Solubility : Not available. Partition coefficient: noctanol/water : Not available. Auto-ignition temperature : Not available. Decomposition temperature : Not available. Viscosity : Kinematic (room temperature): <0.205 cm2/s (<20.
Section 11. Toxicological information Not available. Carcinogenicity Not available. Reproductive toxicity Not available. Teratogenicity Not available. Specific target organ toxicity (single exposure) Name Category Route of exposure Target organs Mineral Spirits (Odorless) Category 3 Not applicable. Med. Aliphatic Hydrocarbon Solvent Category 3 Not applicable.
Ingestion : Adverse symptoms may include the following: nausea or vomiting Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure Potential immediate : Not available. effects Potential delayed effects : Not available. Long term exposure Potential immediate effects : Not available. Potential delayed effects : Not available. Potential chronic health effects Not available.
Section 13. Disposal considerations Disposal methods : The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor.
Section 14. Transport information Special precautions for user : Multi-modal shipping descriptions are provided for informational purposes and do not consider container sizes. The presence of a shipping description for a particular mode of transport (sea, air, etc.), does not indicate that the product is packaged suitably for that mode of transport.
Section 16. Other information Key to abbreviations : ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL 73/78 = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978.