Remote Power Manager (RPM) User’s Manual 34000242 Rev1
Table of Contents 1. Introduction................................................................................................................. 3 2. RPM Package ............................................................................................................. 4 3. Features ..................................................................................................................... 5 4. Installation ........................................................................................
1. Introduction The RPM is an SNMP/Internet ready device designed to allow administrators to remotely and locally control the AC power for up to eight connected devices, such as: servers, routers, modems and telephone networks. With the expandable function of allowing daisy chaining (cascading) of up to 16 client units, administrators can control a total of 128 devices. The RPM offers easy set up and user-friendly communication and control methods.
2. RPM Package The standard RPM package contains a Remote Power Manager Unit with supporting hardware and software. The contents of your package are: Remote Power Manager Unit. Rack mount Brackets. 1-AC Power Cord. 8-RJ-11 to RS232 NT Server Cables (RPM1609 only): For PC communication. 1-RJ-11 Cascade Cable: For RPM daisy chain and UPS connection. 1-CD. The contents of the CD: Quick Install Procedure. SNMP Utility: Configure SNMP card’s IP address and upgrade firmware. MIB files: dgpups.
3. Features • Turn ON/OFF any AC powered device via network, phone or the front panel control buttons. • Integral 10/100Base-T Ethernet port for connection to your TCP/IP network. • Support dial in by modem to control the AC power outlets. • Address-Specific IP security masks prevent unauthorized source from accessing the RPM menu through the network. • Support NMS to control RPM by MIB. User also can use MIB to develop their application interface. • Download data and events log list to server.
4. Installation Procedure 1. Install the mounting brackets. The RPM comes with brackets for mounting in a standard 19-inch rack. To mount the RPM into a rack perform the following procedure: • Attach the mounting brackets to the unit as shown, using the four retaining screws provided for each of the brackets. • Choose a location for the brackets. A notched hole on the vertical rail denotes the middle of a U slot.
4. 5. 6. 7. Program the IP address. (See the SNMP-32 User’s Manual). Set RPM’s front control buttons for Internet ready. (See the Outlook section for the correct operation) Use a browser to monitor and control the RPM. For NT shutdown setup, use the RJ11 to RS322 NT Server cable to connect with server and use the following instruction to configure control panel /UPS in Windows OS. 1. Open your Windows 2000 Control Panel by clicking on “Start”, “Setting”, “Control Panel”. 2.
5. Select the “Log On As: This Account” button, input the appropriate account information, and then click “OK”. 6. Double-click on the Control Panel’s “Power Options” icon. 7. Select the UPS page, and then click on “Select”. 8. Choose the correct manufacturer from the “Select manufacturer” pull-down list, choose the correct COM port, and then click on “Next”.
. Click on the boxes, as shown, and then choose “Negative” for the three voltage settings. Click on “Finish” to keep these settings. Click “OK” at bottom of the “Power Options Properties” window to finish. Note: See the SNMP-32 Series User’s manual for the other functions.
5. Outlook RPM-Rear Panel NT SERVER PORTS A-H: Provides controlled shutdown for NT server. Port A controls receptacle A; Port B controls receptacle B, etc. RPM-LED Table RPM LED Table LED ON The momentary switch is disabled and the output Green receptacle is set for remote control. Red Yellow The receptacle is on and providing power to devices. Indicates the RPM ID number. The RPM master (the RPM with the SNMP card) will display all the connected RPMs.
Receptacle Control Status LED (Green) Receptacle Status LED (Red) Active Module LED (Yellow) Momentary switch for Receptacle Master Power Switch Receptacle Status LED (Red): When the LED is illuminated the receptacle is on and providing AC Power. When the LED is off the receptacle is not providing AC Power. Receptacle Control Status LED (Green): When the control LED is illuminated, the momentary switch is disabled and the output receptacle is set for remote control (Internet Ready).
6. Telephone Access This section will guide you through the Telephone Access to control RPM. 1. Dial up the RPM. 2. After three rings, the RPM will respond by sending out three short beeps to the caller. Then the RPM waits for the user to enter the password. 3. The user enters an access password (default password is 123456789#). 4. The RPM will send out three short beeps to confirm a successful login, or one long beep to deny access. 5. Once logged in, the remote user can punch in 4-8 digits.
iii. When the LED A and H blinking, release the two buttons, the RPM will respond by sending out 4 short beeps to the caller. The password will be restored to default. 12. The RPM is in a waiting loop to receive the command string. Each command string should be entered within 20 seconds. After 180 seconds without any user input, the RPM will logout the user. 13. The 9 command set is for the administrator: 14. 0190# to turn off all of the outlets. 15. 0191# to turn on all of the outlets. 16.
7. Daisy Chaining The Remote Power Manager (RPM) can be Daisy Chained up to a maximum of sixteen units. Each RPM in the Daisy Chain must have its own unique identification number. The default ID# is “0“. The first RPM (Master RPM) must have the SNMP-32 Card install and must be configured before you can begin Daisy Chaining any additional RPMs. Only the first RPM requires the SNMP-32 Card. Follow the procedure below to Daisy Chain the RPMs: Figure 1 - First RPM 1.
Figure 3 - First, second and third RPM 13. Make sure that the third RPM has the Terminator plugged into the iLink port. 14. Remove the Terminator from the second RPM. 15. Connect the second and third RPM together with the iLink cable. 16. Plug the third RPM's power cord into utility power. 17. Turn the master power switch on. 18. Configure the third RPM's ID number (see the SNMP-32 User’s Manual). NOTE: Each RPM must have it's own unique ID#, the default ID# is "0". 19.
8. Obtaining Technical Assistance For Technical Support on the Web, please visit the Support section of our Web site Or visit our online Discussion Forum at www.minutemanups.com In order to diagnose the problem you are having, our technicians need the following information from you.
9. Limited Product Warranty Para Systems Inc. (Para Systems) warrants this equipment, when properly applied and operated within specified conditions, against faulty materials or workmanship for a period of three years from the date of original purchase by the end user. For equipment sites within the United States and Canada, this warranty covers repair or replacement of defective equipment at the discretion of Para Systems. Repair will be from the nearest authorized service center.