Operation Manual

1. How to use rnemory
function
Slide
norrnal/analyze
switch
to
"NORlVl"
positiol'1.
1.
Press
the
memory
button
after
taking
a
measure-
ment.
The display will
go
blank
for
a
moment
then
reappear when
the measurement
has
been memo-
rized. The
memory indicator
(black
dot) will
appear to confirm
that
the reading
is memorized.
A
pointer
will appear at the
"0"
position
on the
contrast
scale. lf the
f-number
scale
is displayed,
the
pointer
will
indicate the corresponding f-
number.
I-J'r--l,
fr.u'J
II
M
n
LI
qrc
I
NOTE
When
the
measurement is
under or over the
meter's measuring range, it cannot be
entered
into
the
memory.
2.
A
second
measurement
can then be taken, and
a
new readout
will
appear
on the
display.
o
When the
f-number scale
is displayed, a
pointer
will
appear
to indicate
the
f irst
measurement, then
a
second
pointer
will appear
for second
measure-
ment.
o
When
the
contrast
scale
is
displayed, the
pointer
at
"0" position
will indicate
the
relative
difference
between the two
measurements.
| 1.422.8 45.68 il162232456490.
5#a
'*
fl.fr o^"''
@l-
,-l
t--t t-l
,sOJ
U
Lll
0
.
I
.
2N. 3.4.
'."ff.il
fi
^'"'
1 1.4 2 2.8 4 5.6 8
11
16 22
32
4564
90
.
AMBI
L-,Li I r
;-;-..--r i fl
i'
*E'j
\
f
LrLf
NOTE
The memory
can
store
up
to
two
measurements.
lf
you
try to
memorize
more
than two
measurements,
a
large letter
"E"
will
appear on the LCD
panel.
"4.-3s
5M'
r: ,-,
LI L'
ISO
,- ,/
tr
-t
o
I
fi ii
^'"'
1
1.4 2 2.4 4 5.6 8 t't t6
?2 32
4564
90
*6fl
'*J
J
aMBl
LrLf
J J,,
''o.5?
\
L L u
1 1.422.8 45.68
11162232455490:
*fi
ii
FNo
f
AMal
lfl,
r
"""71
r
How
to
erase
"E"
from
the
display
Either of two nnethods can
be
used:
Push
the on/recall
button.
"E"
will
be
replaced by
the
most recent
measurement.
In this case, the
first
and second
measurements
are
stored
in
the
memory.
r 1.4 2 2.8 4
5.6 I
1r
16 22 32
4564 90
:
ilm]trfl
Fb
_
aMBl
ou
-t
1
FFN
''orl'/
\
L L L'
Push
measuring
button
in.
"E"
is
erased
and a
new
measurement
is displayed
on
the
LCD
panel.
The
first
and second
measurements are
stored
in the
memory.
o
When
the
f-number
scale
is displayed, changing
the
f
ilm-speed or shutter-speed
setting
will
also
change
the
position
of the
pointer.
a
The
measurements
remain
memorized even
if
measuring-mode
selector
or single/multi-reading
switch
are
moved, or if the
light receptor is
changed.
Thus, measurements
of incident
and/or
reflected
light
for flash or
ambient
light can be
shown
by
the
pointers
on the analog
scale.
o
Even when
the display
goes
off, any
values
stored
in the
memory
are
retained as long as
battery
power
lasts.
+l
1
r!a!
r- ,-
tt tt
lsoJ-
U
Lll
'*
Y.lJ
,,
^'"'
www.orphancameras.com