Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
TROUBLE-SHOOTING CHART
(2186) 1
TROUBLESHOOTING CHART
This section consists of the following items.
CONTENTS page
■■
■■
■ Precautions
(1)To check voltage, use digital Multimeter or an apparatus which input impedance of
10MΩ or greater.
(2)To check conductivity, use a circuit tester of 3V or less.
(3)Check mainly soldering at lead wires or electrical elements and switch operation,
since elements (IC, diode, transistor, resistor, or condenser) seldom cause the
trouble.
(4)When checking, do not push elements or pull lead wires strongly.
(5)When checking voltage at patterns where switch operates, be careful not to prevent
switch operation or to scratch patterns.
(6)Before removing electrical parts, be sure to disconnect Power Supply.
(7)Since this model uses lead-free solder, a soldering iron tip temperature of 280 - 350°C is sufficient.
But when it cannot melt solder, use a higher temperature for a short period of time.
Be sure to control soldering iron tips used for lead-free solder and those for leaded solder so they are
managed separately.
This is because mixing lead-free solder and leaded solder will cause detachment phenomenon.
(8)When handling ICs avoid static electricity.
Caution for Battery and Circuit board disposal
Always follow local regulations for disposal.
Tape over the lithium-ion battery contacts to avoid short-circuiting during disposal.
Caution for Product disposal
Do not dispose of this product together with your household waste.
Please refer to the information of your local community or contact our dealers regarding the proper
handling of end-of-life electric and electronic equipment.
Recycling of this product will help to conserve natural resources and prevent potential negative
consequences for the environment and human health caused by inappropriate waste handling.
■Precautions --------------------------------------------------------------------------------------------------------------------- 1
■Caution for Battery and Circuit board disposal ------------------------------------------------------------------------- 1
■Caution for Product disposal ------------------------------------------------------------------------------------------------ 1
■Trouble code -------------------------------------------------------------------------------------------------------------------- 2
■Map of Electrical Elements-------------------------------------------------------------------------------------------------- 5
(1) I/O FPC ASSY (#0406) --------------------------------------------------------------------------------------------------- 5
(2) FLASH PCB ASSY (#0473)---------------------------------------------------------------------------------------------- 5
(3) TOP COVER FPC ASSY (#0407) -------------------------------------------------------------------------------------- 6
(4) SW FPC-1 ASSY (#0408)------------------------------------------------------------------------------------------------- 7
(5) SW FPC-2 ASSY (#0420)------------------------------------------------------------------------------------------------- 7
(6) GYRO FPC ASSY (#0414) ----------------------------------------------------------------------------------------------- 7
(7) AF CHARGE ASSY (#0521) --------------------------------------------------------------------------------------------- 8
(8) DC JACK PCB ASSY (#0427) ------------------------------------------------------------------------------------------- 9
(9) SLIDER ASSY (#0901) --------------------------------------------------------------------------------------------------- 9
(10) PENTA ASSY (#0580) --------------------------------------------------------------------------------------------------- 9