Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 61
REPAIR GUIDE
Adjustment（Common） b6****** NG for AE Adjustment
**f1**** USB port initialization is not good.
b6050000
input data
**f2**** USB port initialization is not good. b6080000 Brightness
**f3**** Reset of ANIT-SHAKE is not good. b60a0000 Setting of Camera
**f4**** Reset of ANIT-SHAKE is not good. b60c0000 AE check
**f5**** Camera ver. Readout is not good.
**f6**** Camera ver. Readout is not good. Adjustment (ANTI-SHAKE system)
**f8**** Tmp. data read is not good. 91****** NG for VSUB Adjustment
**f9**** Tmp. data read is not good.
91050000
Speed error
**fb**** Setting of Camera mode is not good.
**fc**** Setting of Camera mode is not good. 91080000 Speed error
**fe**** Access of Flash ROM is not good. 91090000 Drive impossible (Pitch, Yaw)
**ff**** Access of Flash ROM is not good.
**c1**** Communication error 91100000 Drive impossible (Pitch, Yaw)
**c3**** Access of Anti-shake is not good. 91110000 Outward and back speed error (Pitch)
**c4**** Access of Flash ROM is not good. 91120000 Outward and back speed error (Yaw)
**c5**** Communication error
**c6**** Communication error 92****** NG for SERVO Adjustment
**c6**** Communication error
92030000
Received data of BreCPU "0x0000"
**c8**** Access of Flash ROM is not good. 92060000 Electric current mode (Speed)(Pitch)
92070000 Electric current mode (Speed)(Yaw)
Adjustment (Image taking system) 920a0000 Electric current mode (Distribution)(Pitch)
71****** NG for Sesitivity Adjustment 920b0000 Electric current mode (Distribution)(Yaw)
71010000
Retry over
92200000
Check Sum error
71020000 Value is too small 92210000 Frequency error
71030000 Value is too large 92220000 Final distribution error (Pitch)
92230000 Final distribution error (Yaw)
73****** NG for Missing Pixel Comp. Adjustment(Blk)
00c20000 There are many black dead pixels. 93****** NG for GYRO Adjustment
00c30000
Both adjoining pixels are dead pixels.
93030000
IC Vref voltage out of a standard
73010000 Abnormally address of dead pixels 93040000 GYRO DC offset value (Pitch)
93050000 GYRO DC offset value (Yaw)
74****** NG for Missing Pixel Comp. Adjustment(Wht) 93060000 Initial value of DAC (Pitch)
00c20000
There are many black dead pixels.
93070000
Initial value of DAC (Yaw)
00c30000 Both adjoining pixels are dead pixels. 93080000 Vibration was detected during adj. (Pitch)
74010000 Abnormally address of dead pixels 93090000 Vibration was detected during adj. (Yaw)
75****** NG for Missing Pixel Comp Adj.(Long Exp.) 94****** NG for SHAKE GAIN Adjustment
75010000
There are many black dead pixels.
94010000
No detection of white line (YAW)
75020000 Abnormally address of dead pixels 94020000 No detection of white line (PITCH)
75030000 0 number of the defect pixels 94030000 PtoP(Yaw)
94040000 PtoP(Pitch)
77****** NG for WB Adjustment 940d0000 No detection of minimum gain.
77010000
Too low exposure
77020000 Too high exposure 94100000 No detection of minimum gain.
77030000 Too low R-Gain on Light source-A 94110000 Rest of shake comp. greater than standard
77040000 Too high R-Gain on Light source-A
77050000 Too low B-Gain on Light source-A 94140000 Rest of shake comp. greater than standard
77060000 Too high B-Gain on Light source-A 94150000 White line is too wide (Pitch)(still)
77070000 Too low R-Gain on Light source-C 94160000 White line is too wide (Yaw)(still)
77080000 Too high R-Gain on Light source-C 94170000 White line is too narrow (Pitch)(slide)
77090000 Too low B-Gain on Light source-C 94180000 White line is too narrow (Yaw)(slide)
770a0000 Too high B-Gain on Light source-C 94190000 White level is too high at width detection(still)
770b0000 R offset standard over on Light source-A 941a0000 White level is too low at width detection(still)
770c0000 B offset standard over on Light source-A
770d0000 R offset standard over on Light source-C e5****** NG for SHAKE Screening
770e0000
B offset standard over on Light source-C
e5010000
GYRO noise standard over (Pitch)
e5020000 GYRO noise standard over (Yaw)
b0****** NG for SS Adjustment e5150000 White line is too wide (Pitch)(still)
b0020000
EEPROM error
e5160000
White line is too wide (Yaw)(still)
e5170000 White line is too narrow (Pitch)(slide)
b0080000 EEPROM error e5180000 White line is too narrow (Yaw)(slide)
b0090000 AS Sw. position error
b4****** NG for AV Adjustment
b4020000
EEPROM Writing error
b4050000 Camera main RAM read error
b4060000 EEPROM Writing error
b4c40000 capture error