Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
56 (2186)
REPAIR GUIDE
16001600
16001600
1600
±±
±±
±
2mm2mm
2mm2mm
2mm
■■
■■
■
Fig. 1Fig. 1
Fig. 1Fig. 1
Fig. 1
Adjustment of the camera shaking compensation (SHAKE GAIN)
Required equipment
Vibration tester
Shake Offset Chart 2
PC with preinstalled the 2186 adjustment program
USB-2 (USB cable)
AC Adapter AC-11
Master Lens for SHAKE
Preparation of the adjustment
1. Set the camera without USB cable and the measuring instrument as shown on the Fig. 1.
Set distance between camera and Shake Offset Chart 2 to 1600mm.
Note 1: Distance between camera and chart means distance between CCD position of the camera and
chart. About CCD position, refer to P. 40 Fig. 3.
Note 2: Use indirect lighting like room light for the lighting of the chart, not to use other direct light
ing. If direct lighting is used, adjustment error often happens because of the mis-detecting of
the cross line of the chart.
2. Set the center of the camera finder to the center of the chart.
3. Confirm whether the center of the chart is located at the center of the screen or not by setting the
camera to after view mode. If the center of the chart is not located at the center of the screen, please
perform setting again.
Procedure of the adjustment
1. Set camera to adjustment mode.
Refer to “Starting up the 2186 adjustment program (in the adjustment mode)” in P. 37.
Attach the Mater lens for SHAKE to the camera, and then set to the adjustment mode.
Confirm that the aperture value is not indicated as “--” on the LCD of the camera.
2. Click “SHAKE GAIN” of the adjustment menu. “Does it adjust?” appears.
3. Click “YES” then take a picture in the automatic mode.
4. Follow the message, “Please turn on shake!” Turn the power of the vibration tester on, and click
“OK” after setting the rotation as follows (Fig.1). 8 or 4 pictures are automatically taken.
Frequency of 60 Hz: 300+/-5 r/min
Frequency of 50 Hz: 250+/-5 r/min
5. Follow the message, “Please turn off shake!” Turn the power of the vibration tester off, and click
“OK” .
6. The adjustment is completed when “OK” is displayed on the adjustment menu.
Frequency of 60 Hz: 300+/-5 r/minFrequency of 60 Hz: 300+/-5 r/min
Frequency of 60 Hz: 300+/-5 r/minFrequency of 60 Hz: 300+/-5 r/min
Frequency of 60 Hz: 300+/-5 r/min
Frequency of 50 Hz: 250+/-5 r/minFrequency of 50 Hz: 250+/-5 r/min
Frequency of 50 Hz: 250+/-5 r/minFrequency of 50 Hz: 250+/-5 r/min
Frequency of 50 Hz: 250+/-5 r/min
Camera: Exposure mode: M, Focusing mode: MFCamera: Exposure mode: M, Focusing mode: MF
Camera: Exposure mode: M, Focusing mode: MFCamera: Exposure mode: M, Focusing mode: MF
Camera: Exposure mode: M, Focusing mode: MF
Lens : Master Lens for SHAKELens : Master Lens for SHAKE
Lens : Master Lens for SHAKELens : Master Lens for SHAKE
Lens : Master Lens for SHAKE
ControlControl
ControlControl
Control
CCD positionCCD position
CCD positionCCD position
CCD position
Shake offset chart Shake offset chart
Shake offset chart Shake offset chart
Shake offset chart
ⅡⅡ
ⅡⅡ
Ⅱ