Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 53
REPAIR GUIDE
■■
■■
■
Fig. 1Fig. 1
Fig. 1Fig. 1
Fig. 1
■■
■■
■
Fig. 1Fig. 1
Fig. 1Fig. 1
Fig. 1
Check / Adjustment of the AE (AE)
Required equipment
Luminance box
L-2101/L-2111 or multi camera tester: EF-8301
AE Master Lens
PC with preinstalled the 2181 adjustment program
USB-2 (USB cable)
AC Adapter AC-11
Procedure of the Check
1. Set the camera to the adjsutment mode.
Refer to “Starting up the 2186 adjustment program (in the adjustment mode)” in P. 37.
Attach the AE Mater lens to the camera, and then set to the adjustment mode.
Confirm that the aperture value is not indicated as “--” on the LCD of the camera.
2. Click “AE”of the adjustment menu. “Please select menu” appears.
3. Click “CHECK”.
4. Set the value of brightness box by following the direction as “Please set light box as EV**”, and then
click “OK”.
5. Measument value is displayed as shown in Fig. 1. Click “OK”.
6. Follow the direction and repeat step 4 and 5.
7. “AE adjustment has completed!” appears when completed.
Procedure of the Adjustment
1. Set the camera to the adjsutment mode.
Refer to “Starting up the 2186 adjustment program (in the adjustment mode)” in P. 37.
Attach the AE Mater lens to the camera, and then set to the adjustment mode.
Confirm that the aperture value is not indicated as “--” on the LCD of the camera.
2. Click “AE”of the adjustment menu. “Please select menu” appears.
3. Click “ADJUST”. “Does it adjust?” appears.
4. Click “YES”. “Please set light box as EV6” appears.
5. Set the value of Luminance box accordingly, and then click “OK”.
“Please set light box as EV15” appears.
6. Set the value of Luminance box accordingly, and then click “OK”.
7. Set the value of Luminance box by following the direction as “Please set light box as EV**”, and then
click “OK”.
8. Measument value is displayed as shown in Fig. 1. Click “OK”.
9. Follow the direction and repeat step 7 and 8.
10. “AE adjustment has completed!” appears when completed.