Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
52 (2186)
REPAIR GUIDE
■■
■■
■
Fig.1Fig.1
Fig.1Fig.1
Fig.1
■■
■■
■
Fig.2Fig.2
Fig.2Fig.2
Fig.2
Aperture Preset Check / Adjustment
Equipment Required
PC with preinstalled the 2186 adjustment program
HIT I/O Tester
Preset Signal Adapter
USB-2 (USB cable)
AC Adapter AC-11
Check
1. Set up the equipment as in Fig. 1, and set camera to “M” mode and “Bulb”.
2. Press Reset Button on HIT I/O Tester so that “00” appears in the display.
3. Set aperture to f/11, and release the shutter.
Check the reading in HIT I/O Tester is within the standard. (Reading appears while Shutter-release
Button is pressed all-the-way down.)
If the reading is out of standard, make Aperture Preset adjustment.
Adjustment
1. Set up the camera and measuring instruments as shown in Fig. 1.
2. Set the camera to the adjsutment mode.
Refer to “Starting up the 2186 adjustment program (in the adjustment mode)” in P. 37.
Attach the Preset Sinal Adapter to the camera, and then set to the adjustment mode.
Confirm that the aperture value is not indicated as “--” on the LCD of the camera.
3. Press the Reset button of the H.I.T. I/O tester to reset the display to “00”.
4. Select “PRETRIGGER” in the adjustment menu.
5. When “Execute 1st release?” appears, click “OK”.
6. Shutter-releasing is automaticallly done. Check the value of the H.I.T. I/O tester.
7. Press the Reset button of the H.I.T. I/O tester to reset the indicated value to “00”.
8. When “Execute 2nd release?” appears, click “OK”.
9. The second shutter-releasing is automaticallly done. Check the value of the H.I.T. I/O tester.
10. Input the average value of 1st and 2nd shutter-releasing (Fig. 2), and then click “OK”.
11. Repeat step 5 to 10 for f/5, f/10, f/20 respectively.
12. “OK” appears on the adjustment menu when completed.
CameraCamera
CameraCamera
Camera
Exposure mode: M Exposure mode: M
Exposure mode: M Exposure mode: M
Exposure mode: M
Focus mode: MF Focus mode: MF
Focus mode: MF Focus mode: MF
Focus mode: MF
Standard f/11: Ab - bb
HIT I/O TesterHIT I/O Tester
HIT I/O TesterHIT I/O Tester
HIT I/O Tester
PRE/FLA: PRESET PRE/FLA: PRESET
PRE/FLA: PRESET PRE/FLA: PRESET
PRE/FLA: PRESET
Preset Signal AdapterPreset Signal Adapter
Preset Signal AdapterPreset Signal Adapter
Preset Signal Adapter
NOTE:These indications look similar
in HIT I/O Tester display
-------- 6
-------- b