Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 51
REPAIR GUIDE
1st(1)1st(1)
1st(1)1st(1)
1st(1)
2nd(2)2nd(2)
2nd(2)2nd(2)
2nd(2)
3rd(3)3rd(3)
3rd(3)3rd(3)
3rd(3)
4th(4,5,6)4th(4,5,6)
4th(4,5,6)4th(4,5,6)
4th(4,5,6)
6th(8)6th(8)
6th(8)6th(8)
6th(8)
7th(9)7th(9)
7th(9)7th(9)
7th(9)
8th(10)8th(10)
8th(10)8th(10)
8th(10)
5th(7)5th(7)
5th(7)5th(7)
5th(7)
3rd,4th,6th3rd,4th,6th
3rd,4th,6th3rd,4th,6th
3rd,4th,6th
5th5th
5th5th
5th
2nd,8th2nd,8th
2nd,8th2nd,8th
2nd,8th
1st,7th1st,7th
1st,7th1st,7th
1st,7th
4th4th
4th4th
4th
2nd2nd
2nd2nd
2nd
3rd3rd
3rd3rd
3rd
1st1st
1st1st
1st
5th5th
5th5th
5th
6th6th
6th6th
6th
7th7th
7th7th
7th
8th8th
8th8th
8th
■■
■■
■
Fig.1Fig.1
Fig.1Fig.1
Fig.1
■■
■■
■
Fig.2Fig.2
Fig.2Fig.2
Fig.2
Chart Measuring point
3rd(3), 4th(4,5,6), 6th(8) ISLAND AF Chart-I for 2163 (Horizontal) A - D
5th(7) ISLAND AF Chart-I for 2163 (Vertical) E - H
1st(1), 7th(9) ISLAND AF Chart-II for 2163 (Horizontal) I - L
2nd(2), 8th(10) ISLAND AF Chart-II for 2163 (Horizontal) * M - P
Island group
When checking the reading at 2nd island group and 8th island group, use AF Chart-II for 2163 upside down.
EZ SHIFT
Decide the amount of shift by getting the average of 4 points of each island.
Procedure
1. In the “SHIFT VALUE” of “EZ Check”(Fig. 1), set the shift amount of a block number to be shifted
by clicking up/down button of each block.
2. Select the island located at the left of the set block.
3. After shifting, perform focusing.
■■
■■
■
Island (Block) Group Layout Island (Block) Group Layout
Island (Block) Group Layout Island (Block) Group Layout
Island (Block) Group Layout
■■
■■
■
Set point of focus frame and Island No. Set point of focus frame and Island No.
Set point of focus frame and Island No. Set point of focus frame and Island No.
Set point of focus frame and Island No.