Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 49
REPAIR GUIDE
■■
■■
■
Fig.1Fig.1
Fig.1Fig.1
Fig.1
EZ Adjustment
Be sure to perform the adjustment for all island groups in series according to the display after replacing
CCD MODULE ASSY.
Adjustment
1. Set up the equipment ( refer to P. 48 Fig. 1 , Fig. 2).
2. Set the camera to the adjsutment mode. Refer to“Starting up the 2186 adjustment program (in the
adjustment mode)” in P. 37.
3. Click “EZ”of the adjustment menu. “Please select menu” appears.
4. Click “ADJUST”.
5.“Does it adjust?” appears. Click “YES”.
“Adjust <3, 4, 5 ISLAND> Please set chart position as <A>” appears. (Fig. 1)
6. Align the focus frame on the indicated position, and then click OK.
Use the appropriate chart according to the desired island group. (See table below)
7. Repeat step 5.
8. “OK” appears in adjustment mode when completed.
When checking the reading at 2nd island group and 8th island group, use AF Chart-II for 2163
upside down.
Chart Measuring point
3rd(3), 4th(4,5,6), 6th(8) ISLAND AF Chart-I for 2163 (Horizontal) A - D
5th(7) ISLAND AF Chart-I for 2163 (Vertical) E - H
1st(1), 7th(9) ISLAND AF Chart-II for 2163 (Horizontal) I - L
2nd(2), 8th(10) ISLAND AF Chart-II for 2163 (Horizontal) * M - P
Island group