Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
46 (2186)
REPAIR GUIDE
■■
■■
■
Fig. 3Fig. 3
Fig. 3Fig. 3
Fig. 3
■■
■■
■
Fig. 1Fig. 1
Fig. 1Fig. 1
Fig. 1
■■
■■
■
Fig. 2Fig. 2
Fig. 2Fig. 2
Fig. 2
1,955mm1,955mm
1,955mm1,955mm
1,955mm
AF Chart-AF Chart-
AF Chart-AF Chart-
AF Chart-
ⅢⅢ
ⅢⅢ
Ⅲ
for 2163 for 2163
for 2163 for 2163
for 2163
AF Master LensAF Master Lens
AF Master LensAF Master Lens
AF Master Lens
Lens mount surfaceLens mount surface
Lens mount surfaceLens mount surface
Lens mount surface
CameraCamera
CameraCamera
Camera
Focus mode: MF Focus mode: MF
Focus mode: MF Focus mode: MF
Focus mode: MF
Align center of each island with the chart.Align center of each island with the chart.
Align center of each island with the chart.Align center of each island with the chart.
Align center of each island with the chart.
AF Area Adjustment
Adjustment
1. Set up the equipment as in Fig. 1.
2. Set the camera to the adjsutment mode.
Refer to “Starting up the 2186 adjustment program (in the adjustment mode)” in P. 37.
3. Click “AF”of the adjustment menu. “Does it adjust?” appears.
4. Click “YES”. “Please select menu” appears.
5. Click “AREA” and then click “START”. Automatic adjustment starts and displays waveform and
readings.
Check that each line has two dents like the ones in Fig. 2, and the readings X0 and Y0 are within the
standard. If Y0 reading is beyond the standard, follow the adjustment procedure below.
6. Adjust the sub-mirror position as in Fig. 3.
7. After completion of adjustment, click “STOP” and then “END”.
TORX L-WrenchTORX L-Wrench
TORX L-WrenchTORX L-Wrench
TORX L-Wrench
Standard Ｘ0：0±0.35 mm（check only）
Ｙ 0：0± 0.2 mm