Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 45
REPAIR GUIDE
7985-1021-017985-1021-01
7985-1021-017985-1021-01
7985-1021-01
Preparation before AF adjustment
Note: After replacing CCD MODULE ASSY and/or MIRROR BOX ASSY or its relative parts, always
perform AF Area Adjustment (pg. 46) to EZ Adjustment (pg. 49).
If customer says focus fucntion is not normal, perform this adjustment too.
Preparations
The following items should have been completed before starting AF adjustment.
1. Peform this adjustment without FRONT COVER ASSY, after disassemble.
2. When CCD sensor module is out of position after replacing CCD MODULE ASSY, tighten three AF
adjusting screws until they stop, then evenly loosen them by 0.4mm (1.14 turns).
Equipment Required
See the list on P.62 for the measuring instruments, tools and jigs.
PC with preinstalled the 2186 adjustment program
AF Master Lens
AE Master Lens
AF Chart I for 2163
AF Chart II for 2163
AF Chart III for 2163
USB-2 (USB cable)
AC Adapter AC-11
AF-Y/P Adjuster
AF Tripod Attachment-II
Grip Ring
Hexagon Bar Wrench (1.5) or Hexagon Screwdriver
Fluorescent (FL40S W-SDL) (EZ check and adjustment)
Flood Lamp (AF Area and Pitch Yaw adjustment)
(color temperature of 2800 degrees K and brightness
higher than or equal to EV 10)
AF Master LensAF Master Lens
AF Master LensAF Master Lens
AF Master Lens
Yaw Adjusting PlateYaw Adjusting Plate
Yaw Adjusting PlateYaw Adjusting Plate
Yaw Adjusting Plate
Pitch Adjusting PlatePitch Adjusting Plate
Pitch Adjusting PlatePitch Adjusting Plate
Pitch Adjusting Plate
AF-Y/P JigAF-Y/P Jig
AF-Y/P JigAF-Y/P Jig
AF-Y/P Jig
AF TripodAF Tripod
AF TripodAF Tripod
AF Tripod
Attachment-IIAttachment-II
Attachment-IIAttachment-II
Attachment-II
TripodTripod
TripodTripod
Tripod
Grip RingGrip Ring
Grip RingGrip Ring
Grip Ring
Setting for EZ check and adj.Setting for EZ check and adj.
Setting for EZ check and adj.Setting for EZ check and adj.
Setting for EZ check and adj.