Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
44 (2186)
REPAIR GUIDE
■■
■■
■
Fig.2Fig.2
Fig.2Fig.2
Fig.2
■■
■■
■
Fig.1Fig.1
Fig.1Fig.1
Fig.1
Adjustment Manual Set SS
Equipment Required
PC with preinstalled the 2186 adjustment program
Shutter Tester
USB-2 (USB cable)
AC Adapter AC-11
Procedure of the adjustment
1. Set camera to adjustment mode.
Refer to “Starting up the 2186 adjustment program (in the adjustment mode)” in P. 37.
*Turn off the AS switch.
2. Click “SS” of the adjustment menu. “Does it adjust?” appears. Click “YES”.
3. “Execute 1st release?” appears. Click “OK”.
4. Repeat step 3 to perform shutter release three times, and then calculate an average of readings at
B-Range (SS:1/4000).
5. Input SS average [μs] in the window (Fig. 1).
6. If the input value is within the standard, “OK” appers and adjustment is completed.
If the input value is out of standard, repeat from step 3.
Shutter Tester Shutter Tester
Shutter Tester Shutter Tester
Shutter Tester
FUNC: EXP FUNC: EXP
FUNC: EXP FUNC: EXP
FUNC: EXP
CAMERA CAMERA
CAMERA CAMERA
CAMERA
Exposure mode: M Exposure mode: M
Exposure mode: M Exposure mode: M
Exposure mode: M
A S : OFF A S : OFF
A S : OFF A S : OFF
A S : OFF
S S : 1/4000 S S : 1/4000
S S : 1/4000 S S : 1/4000
S S : 1/4000
A S A S
A S A S
A S
：：
：：
：
OFFOFF
OFFOFF
OFF
Standard Value: 0.265ms - 0.305ms