Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
42 (2186)
REPAIR GUIDE
■■
■■
■
Fig. 1Fig. 1
Fig. 1Fig. 1
Fig. 1
■■
■■
■
Fig. 3Fig. 3
Fig. 3Fig. 3
Fig. 3
■■
■■
■
Fig. 2Fig. 2
Fig. 2Fig. 2
Fig. 2
■■
■■
■
Fig. 4Fig. 4
Fig. 4Fig. 4
Fig. 4
Numbers mean the degrees of rotating adjusting screwNumbers mean the degrees of rotating adjusting screw
Numbers mean the degrees of rotating adjusting screwNumbers mean the degrees of rotating adjusting screw
Numbers mean the degrees of rotating adjusting screw
Arrows mean the direction of rotating adjusting screwArrows mean the direction of rotating adjusting screw
Arrows mean the direction of rotating adjusting screwArrows mean the direction of rotating adjusting screw
Arrows mean the direction of rotating adjusting screw
Procedure of CCD AORI checking
1. Set 2186 camera to adjustment mode.
Refer to “Starting up the 2181 adjustment program (in the adjustment mode)” in P. 37.
2. Click “AORI & CENTER” in adjustment menu.
3. Click “2186” when “Please select master data” appears. (Fig. 1)
4. Click MASTER BODY “AORI & CENTER” in AORI & CENTER Adjustment menu(Fig. 2) and
perform shutter-release.
5.“Setting Data of master body has complete!”appers when reading Master body data is completed.
6. Click “END” in AORI & CENTER Adjustment menu.
7. Click “ADJUSTMENT END” in adjustment menu.
8. Set target camera to adjustment mode. Exchange Master camera for target camera.
Be careful to exchange camera to avoid any change to the setting.
9. Click “AORI & CENTER” in adjustment menu. Select the model specified as master body in Fig.1.
10. Click CHECK“AORI” in AORI & CENTER Adjustment menu. (Fig. 2)
11. Check the value disPlayed in Aori Adjusment window, whether value of“C” and “dPI” is within the
following standard. (Fig. 3)
Standard value of C: From -10 to 10
Standard value of dPI: From -10 to 10