Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
40 (2186)
REPAIR GUIDE
■■
■■
■
Fig.1Fig.1
Fig.1Fig.1
Fig.1
■■
■■
■
Fig.2Fig.2
Fig.2Fig.2
Fig.2
470mm470mm
470mm470mm
470mm
■■
■■
■
Fig.3Fig.3
Fig.3Fig.3
Fig.3
ChartChart
ChartChart
Chart
Luminance must be betweenLuminance must be between
Luminance must be betweenLuminance must be between
Luminance must be between
Ev10.7 and Ev 11.3.Ev10.7 and Ev 11.3.
Ev10.7 and Ev 11.3.Ev10.7 and Ev 11.3.
Ev10.7 and Ev 11.3.
Align the hights of the center ofAlign the hights of the center of
Align the hights of the center ofAlign the hights of the center of
Align the hights of the center of
the chart and the center of lens.the chart and the center of lens.
the chart and the center of lens.the chart and the center of lens.
the chart and the center of lens.
Setting for the adjustment of CCD AORI & CENTER
Required equipment
PC with preinstalled the 2186 adjustment program
Master body (Mass Production camera of 2186)
AE Master Lens
2181 AORI-Chart
Hexangular wrench (1.5) or hexangular screwdriver
Setting the Master body and the chart
1. Setting all equipment according to the order listed below (Fig. 1).
Caution: Use stable tripod. Please be careful to detach camera from AF Master Lens without
changing any condition, like the position of tripod.
If some changes happen, you can not peform correct adjustment.
Luminance on the chart must be between Ev10.7 and Ev 11.3.
1) Set Grip Ring to the tripod and set Master Lens to Grip Ring.
2) Attach Master body to Master Lens.
3) Set Master body and chart. Distance between Master body and chart is 470mm.
4) Look into the finder of Master body.
5) Focusing to the chart by rotating the focus ring of Master Lens.
6) Align the center of foucus frame to the center of the chart.
7) Confirm whether cross line of the chart is located at the center of the screen or not by setting the
camera to after view mode. If cross line is not located at the center of the screen, please perform
setting, step 1 to step 6 again.
Position of CCDPosition of CCD
Position of CCDPosition of CCD
Position of CCD
Master bodyMaster body
Master bodyMaster body
Master body
Exposure mode: MExposure mode: M
Exposure mode: MExposure mode: M
Exposure mode: M
Focus mode: MFFocus mode: MF
Focus mode: MFFocus mode: MF
Focus mode: MF
Position of CCDPosition of CCD
Position of CCDPosition of CCD
Position of CCD
Fluorescent light stand SQ967W
Tripod
USB-2 (USB cable)
AC Adapter AC-11
Grip Ring