Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 8
KONICA MINOLTA PHOTO IMAGING, INC.
This information should be filed in your service manual.
SUPPLYMENTARY INFORMATION
symptom Cause Measure
Eject lever does not lock.
Metal plate and a lever link component interfere.
A parting part and a lever link component
interfere.
Eject connector (9383-
0561-50) exchange
CF card cannot be inserted
fully.
At the time of reappearance, it is in the state
where CF card was inserted, and when pushing
eject button and taking out a card, a finger is
touching so that it may support CF card.
It recurs in the timing.
Eject connector (9383-
0561-50) exchange
F -- Display BL contact FPC pattern dirt
BL contact holder assy
(2186-0150) exchange
Anti-Shake access lamp stays
on.
Carbon shaft holder SP at the slider A side of
Slider assy came off.
Reinstall Carbon shaft
holder SP of Slider assy
(2186-0901)
Abnormal image -- entirely
black
IC on CCD PCB destroyed (output 0V).
Presumption: It was the full destruction of IC
which was damaged by the connection mistake to
a unit checker.
CCD assy (2186-0271)
exchange
Abnormal image -- entirely
white
IC on CCD PCB destroyed (output 2V).
Presumption: It is the full destruction of IC
which was damaged by the connection mistake to
a unit checker.
CCD assy (2186-0271)
exchange
Preview button does not
function
No click feeling due to misalignment of SW FPC.
Preview button SW
FPC re-installation