Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 6
KONICA MINOLTA PHOTO IMAGING, INC.
This information should be filed in your service manual.
SUPPLYMENTARY INFORMATION
CODE NO. 2186 Series
SERVICE MANUAL
SUPPLEMENTARY
INFORMATION
MODEL
DYNAX 5D
MAXXUM 5D
α SWEET DIGITAL
α 5 DIGITAL
No. QS FA 2186-S06E Dec.. 2005
symptom Cause Measure
Unexposure at the first time
after leaving for a certain
period. (Error 58)
Pressure to the Shutter assy cam roller was
applied for a certain period.
AF charge assy (2186-
0521-02) and shutter
assy (2186-0210) ex-
change
Fault in Anti-Shake function
(The initial position setting
cannot be done at the time of
the power SW ON. Vibration
sound generated.)
Aori Adj screw was mixed in the slider assy.
(surplus parts)
Surplus parts removal.
No Anti-Shake scale. Deformation of Anti-Shake SW contact (the first
and second ones were bent)
Anti-Shake SW contact
(2186-1420) exchange
Anti-Shake scale cannot be
turned OFF.
Deformation of Anti-Shake SW contact (the first
and second ones were bent)
Anti-Shake SW contact
(2186-1420) exchange
Coupler drive repeats at the
power ON.
LCD harness (blue) was caught between chassis. Unclip LCD harness
(2186-0442).
Initial repair information