Service manual
Table Of Contents
- 1.pdf
- 3-4.pdf
- 5.pdf
- REPAIR GUIDE
- Precautions
- 1. Disassembly of the exterior parts
- ■Wires arrangement
- 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY
- 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER
- 4. Disassembly of the CCD ASSY, SHUTTER ASSY
- ■CCD inclination adjustment / repair
- 5. Disassembly-1 of the MIRROR BOX ASSY
- 6. Disassembly-2 of the MIRROR BOX ASSY
- 7. Disassembly-3 of the MIRROR BOX ASSY
- 8. Disassembly of the BATTERY CHAMBER, LCD 101
- 9. Disassembly of the TOP COVER ASSY
- 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY
- ■Required adjustment, setting and confirmation items after repairing(exchanging parts)
- ■Related adjustment and required setting items
- ■Viewfinder Back Adjustment
- ■Preparing the 2186 adjustment program
- ■Starting up the 2186 adjustment program (in the adjustment mode)
- ■Adjustment of the PI-PR
- ■Adjustment of the frequency for camera shaking (FREQUENCY)
- ■Adjustment of the servo for camera shaking (SERVO)
- ■Adjustment of the gyro for camera shaking (GYRO)
- ■Adjustment of CCD Vsub voltage (VSUB)
- ■Setting for the adjustment of CCD AORI & CENTER
- ■Adjustment / Checking of CCD AORI & CENTER
- ■Manual Set SS & X-Sync. Time-lag Check
- ■Adjustment Manual Set SS
- ■Preparation before AF adjustment
- ■AF Area Adjustment
- ■Pitch Yaw Adjustment
- ■FLATNESS Adjustment
- ■EZ Check / Adjustment
- ■EZ Adjustment
- ■EZ Check
- ■EZ SHIFT
- ■Aperture Preset Check / Adjustment
- ■Check / Adjustment of the AE (AE)
- ■Sensitivity adjustment (CCD GAIN)
- ■Adjustment of the defective pixel (DEFECT PIXEL)
- ■Adjustment of white balance (WB)
- ■Adjustment of the camera shaking compensation (SHAKE GAIN)
- ■FLASH LEVEL SHIFT
- ■Setting of Destination (DESTINATION)
- ■CAMERA LOG
- ■LCD All Segment On
- ■Light Source-A Maintenance
- ■Error code on adjustment program
- ■Measuring instrument
- ■Subsidiary Materials
- REPAIR GUIDE
- 6.pdf
- TROUBLESHOOTING CHART
- 7.pdf
- 8.pdf
- 9.pdf
(2186) 2
KONICA MINOLTA PHOTO IMAGING, INC.
This information should be filed in your service manual.
SUPPLYMENTARY INFORMATION
CODE NO. 2186 Series
SERVICE MANUAL
SUPPLEMENTARY
INFORMATION
MODEL
DYNAX 5D
MAXXUM 5D
α SWEET DIGITAL
α 5 DIGITAL
2m2m
2m2m
2m
No. QS FA 2186-S02E Sep. 2005
Standard Reflection Paper IIStandard Reflection Paper II
Standard Reflection Paper IIStandard Reflection Paper II
Standard Reflection Paper II
Lens: 2613Lens: 2613
Lens: 2613Lens: 2613
Lens: 2613
Camera:Camera:
Camera:Camera:
Camera:
PWB: FlashPWB: Flash
PWB: FlashPWB: Flash
PWB: Flash
Exposure mode: AExposure mode: A
Exposure mode: AExposure mode: A
Exposure mode: A
Aperture: f/4Aperture: f/4
Aperture: f/4Aperture: f/4
Aperture: f/4
ISO: 100ISO: 100
ISO: 100ISO: 100
ISO: 100
Flash mode: PTTLFlash mode: PTTL
Flash mode: PTTLFlash mode: PTTL
Flash mode: PTTL
External flash control
Treatment on underexposure by #2181 with external flash
1) External flash adjustment to lower pre-flash level (no service information issued)
2) Camera adjustment to amplify final flash level by firmware upgrade and 1). (cf. Supplementary Informa-
tion No. QS FA 2181-S04E)
Putative problem with DSLRs (#2186 or later) plus external flash
When an external flash with 1) adjustment is used with these DSLRs, it results in overexposure.
Treatment at after-sales service facilities
In booking in a claimed product, confirm the condition of user's product and book in his/her external flash
and #2181 if possible.
1. Upgrade #2181 firmawre and conduct adjustment.
cf. Supplementary Information No. QS FA 2181-S04E
2. Adjust the external flash to lower pre-flash level (flat flash-firing).
cf. Supplementary Information No. QS FA 2181-S04E
3. Photograph the standard reflection paper II by the #2186 with the external flash under the condition below:
4. Open the image file via the color imformation software 'Color Calculator 2'
Confirm that the G level is within the range of 127+-10.
(Refer to page 5-6 of #2181 Check List for the setting of the color information software 'Color Calculator 2'.
If not, implement Flash Level Shift (cf. page 57 of Repair)
With Adobe Photoshop:
1. Specify the image range of 256x256 pixels
2. Select 'Histogram' in the 'Image' manu options.
3. Read the average value with specifying green for the channel.