SERVICE MANUAL DYNAX 5D MAXXUM 5D SWEET DIGITAL 5 DIGITAL COMMON MODEL: DYNAX 5D MAXXUM 5D SWEET DIGITAL (Black) SWEET DIGITAL (Silver) 5 DIGITAL PEU/PHK/PAS/PAU/Mid-East-India/ Korea/Iran-Sylia PUSA/ PCA/South-America/Taiwan PJ PJ PMSH-SKD model TECHNICAL ILLUSTRATION PARTS NOTICE WITH PARTS LIST TECHNICAL REPAIR MANUAL KONICA MINOLTA PHOTO IMAGING, INC.
Code QS FA9220-2186-01 2186 Service Manual Index Division Camera CS Division Completed September 30, 2005 Approved by Verified by Yata Page １ Written by Ueno Section/TTL number of pages 1 Service Manual Index 1 2 Specifications 1 ３ Parts List Index 3 ４ Parts List 12 ５ Repair Guide 62 ６ Trouble-Shooting Chart 9 ７ Check List 8 Revision History Date of issue/Version 26/08/2005 13/09/2005 Reason (Revision part) First issued Error correction (pg.
(2186) 1 Specifications Type Type Interchangeable-lens digital SLR camera Number of effective pixels Approx. 6.1 million (3016x2008) Camera block CCD Unit cell size Recording media Recording block File format 23.5mm x 15.7mm (APS-C size equivalent) Interline primary-color, interlace scan Total pixels: 6.3 million 7.8μm x 7.8μm TypeⅠand TypeⅡCompactFlash cards, Microdrive, SD memory card/ MultiMedia Card (with SD-CF1 in use) JPEG/ RAW/ RAW+JPEG [DCF 2.
(2186) 1 INDEX ．．．．．． 11 2186-0521 ．．．．．． 6 2186-1116 ．．．．． 11 2186-0121 ．．．．．． 11 2186-0526 ．．．．．． 6 2186-1119 ．．．．． 11 2186-0122 ．．．．．． 11 2186-0580 ．．．．．． 5 2186-1120 ．．．．． 10 2186-0131 ．．．．．． 9, 10 2186-0584 ．．．．．． 5 2186-1126 ．．．．． 1 2186-0134 ．．．．．． 1 2186-0721 ．．．．．． 4 2186-1127 ．．．．． 1 2186-0135 ．．．．．． 9, 10 2186-0901 ．．．．．． 4 2186-1128 ．．．．． 1 2186-0141 ．．．．．． 3 2186-1130 ．．．．． 1 2077-0145 ．．．．．． 10 2186-1001 ．．．．．． 2 2186-1131 ．．．．．
2 (2186) PARTS LIST INDEX 2186-1327 ．．．．．． 10 2186-1444 ．．．．．． 11 2186-1610 ．．．．． 9 2186-1328 ．．．．．． 10 2186-1445 ．．．．． 11 2186-1611 ．．．．． 9 2186-1329 ．．．．．． 11 2186-1446 ．．．．．． 11 2186-1612 ．．．．． 10 2186-1330 ．．．．．． 9 2186-1469 ．．．．．． 9 2186-1613 ．．．．． 9 2186-1331 ．．．．．． 9 2186-1470 ．．．．．． 9 2186-1614 ．．．．． 10 2186-1332 ．．．．．． 9 2186-1471 ．．．．．． 9 2089-1620 ．．．．． 9 2186-1333 ．．．．．． 9 2186-1473 ．．．．．． 9 2089-1621 ．．．．． 9 2186-1334 ．．．．．． 9
(2186) 3 INDEX 2186-4404 ．．．．．． 12 9391-0807-02 ．．．．．． 12 9746-2030-01 ．．．．． 2 2186-4508 ．．．．．． 8 9391-0807-03 ．．．．．． 12 2186-4511 ．．．．．． 11 9391-0807-04 ．．．．．． 12 9747-1440-01 ．．．．． 7 2186-4514 ．．．．．． 2 9391-0807-05 ．．．．．． 12 9747-1730-01 ．．．．． 2186-4520 ．．．．．． 2 8, 9, 11 9747-1735-01 ．．．．． 3, 5, 7, 8, 9, 10 9391-1207-00 ．．．．．． 12 9747-1740-01 ．．．．． 1, 2, 8, 10, 11 ．．．．．． 5 9391-1207-02 ．．．．．． 12 9747-1740-15 ．．．．． 1 2186-5022 ．．．．．． 5 9391-1207-04 ．．．．．． 12 9747-
9747-1755-04(2)(-650) 9747-1755-15(2)(-090,-100,-300,-600) 9611-2035-04(-650) 9611-2035-15(-090,-100,-300,-600) 9761-1470-01 2186-5041-01 2098-5045-02 9744-1665-04(2)(-650) 9744-1665-15(2)(-090,-100,-300,-600) See Page 9,10 9747-1740-01(-650) 9747-1740-15(-090,-100,-300,-600) 9744-1620-01 C A 2186-1301-01(-090) 2186-1302-01(-300) 2186-1303-01(-100) 2186-1304-01(-600) 2186-1305-02(-650) 9611-1625-01(2) 2186-0134-01 2186-0408-02 9384-2191-00 (10X10mm) 2186-0442-01 See Page 2 9384-2290-90 A (5X20mm)
(2186) 1 PART NAME QTY. 2186-0134-01 EYE PIECE FRAME ASSY 接眼枠セット 1 2186-0174-01 BATTERY COVER ASSY 電池蓋セット 1 (2186-1076-02) BATTERY COVER HINGE SHAFT 電池蓋ヒンジ軸 1 (2186-1079-03) BATTERY COVER SP 電池蓋ＳＰ 1 2186-0408-02 SW FPC-1 ASSY ＳＷフレキ１セット 1 2186-0442-01 LCD HARNESS ＬＣＤハーネス 1 2186-1043-02 LCD GND PLATE ＬＣＤ ＧＮＤ板 1 2186-1126-02 STANDARD PLATE 定格銘板 1 2186-1127-02 PLACE PLATE MALAYSIA 生産地銘板 1 2186-1128-01 BODY NO.
747-1740-01 2186-0441-02 2186-0402-03 2186-1021-01 9747-1740-01 B 2186-4520-01 2186-0406-02 D 2186-1175-01(2) A 9384-2290-90 (5X20mm) 2186-2709-01 9384-2191-00(3) (10X10mm) C 9744-1615-01 C 2186-2708-02 A 2186-1173-01 9749-1735-15 2186-4514-01 D See Page 3 2186-1176-01 B 2186-0410-08 9384-2290-90 (5X10mm) 2186-1172-03 A See Page 1 9745-2025-01(2) 9745-2025-01(2) 9611-2025-01(2) 2186-1078-02 9748-2050-15(2) 9747-1740-01 2186-2940-01 2186-1012-01 2186-1013-03 9748-2045-01 2186-1001-03 218
(2186) 2 PART NAME QTY.
9745-2025-01 9748-2050-01(2) 2186-1003-03 9748-2050-01 9745-2025-01(2) 9747-1735-01 2186-1005-03 2186-5034-01 2186-1066-02 9611-2025-01(2) 9744-1625-01(2) 9748-2050-01 See Page 8 9748-2050-01 2186-4033-01 9747-1735-01 2186-0141-02 2186-5033-01 2186-1146-02 2186-1144-02 9748-2050-01 See Page 5,6,7
(2186) 3 PART NAME QTY.
(2186-0412-01) 9747-1745-01(4) [9384-2190-50] (3.
(2186) 4 PART NAME QTY.
2186-0500-01 [2186-5022-01] [9747-1745-01](2) (2181-0580-01) [2186-5048-02] [2186-0506-01] [9747-1735-01](2) [9384-2290-90] (9X15mm) [2186-0503-01] [9747-1745-01](2) [2186-0584-01] (9747-1745-01)(3) See Page 6 [2186-5820-01] ~ 2186-5025-01 [2186-5028-01] (Some) (2162-2659-01)(3) [2186-5805-02] (9384-2190-50) (3X5mm) (2186-0265-02) [2181-5016-01] (2082-5054-01)(3) (2162-2658-01)(3)
(2186) 5 PART NO PART NAME 2186-0500-01 MIRROR BOX ASSY QTY. 1 (2186-0265-02) AF MODULE ASSY ＡＦモジュールセット 1 (2186-0580-01) PENTA ASSY ペンタセット 1 [2186-0503-01] INF LCD HOLDER ASSY ＩＦ ＬＣＤホルダーセット 1 [2186-0506-01] TOUKO ASSY 投光セット 1 [2186-0584-01] DIOPTER ASSY 視度調セット 1 [2181-5016-01] FRESNAL SPRING 焦点板ＳＰ 1 [2186-5022-01] SPC LIGHT SHIELD SHEET ＳＰＣ遮光シート 1 2186-5025-01 VB WASHER A (0.05mm) ＶＢワッシャＡ 2186-5026-01 VB WASHER B (0.1mm) ＶＢワッシャＢ 2186-5027-01 VB WASHER C (0.
2186-0500-01 (2186-2532-02)(2) (2186-2533-02)(2) (9747-1750-01) (2186-0254-01) See Page 7 (2186-2512-01) (9747-1750-01)(2) (2186-2535-01) (2186-2534-01) (2186-2530-02) (2186-1511-02) (2186-1524-03) (2163-1521-01) (2186-1813-01) (9747-1745-01) (2181-5123-01)(2) (2186-1522-01) (9749-1730-01) (2186-1523-01) (2162-1547-01) (2181-1515-01) (2186-1525-01) (2186-1545-02) (2186-1520-01) (2186-1521-01) (9761-2055-04)(6) (2186-0526-01) (9747-1745-01) (2186-0521-01)
(2186) 6 PART NO PART NAME 2186-0500-01 MIRROR BOX ASSY QTY.
2186-0500-01 (2186-5110-01) (9769-1730-01) (2186-5110-01) (9769-1730-01) (2186-0150-01) (9769-1740-01) (2186-0514-01) [2186-5806-02] (9769-1740-01) (2186-1812-01) (2186-0515-01) (2186-5109-01) (2186-0180-01) (2186-5151-01) (2181-5108-02) (9747-1735-01)(4) (2186-5101-01) (9747-1745-01)(2) (2186-5107-02) (2186-5102-01) (2186-1543-02) (2162-1544-01) (9747-1440-01) (2186-1548-01) (2186-1542-01) (2186-5112-01)
(2186) 7 PART NO PART NAME 2186-0500-01 MIRROR BOX ASSY QTY.
9384-2290-90 (9X15mm) 9761-2055-01 2186-1088-01 9384-2191-00 (6X20mm) 9749-2035-01(2) 9747-1740-01 9769-1730-01 2186-1153-02 2186-1002-04 2186-1065-02 2186-1159-01 2186-0154-01 2186-1156-01 9747-1735-01 9747-1735-01 2186-1151-02 2186-0414-02 2186-1071-03 2186-0155-01 2186-4508-02 2186-1086-01 9747-1750-01 2186-1072-01 9747-1740-01(2) 2186-1083-01 2186-1087-01 2186-1081-02 9749-1735-15 2186-0473-01 2186-1082-02(2) 2186-0427-03 9747-1740-01(2) 9747-1730-01(2) 2186-1073-01 2186-1041-02 2186-
(2186) 8 PART NAME QTY.
2186-0131-01(-650) 2186-0135-01(-090,-100,-300,-600) (9747-1745-04)(2)(-650) (9747-1745-15)(2)(-090,-100,-300,-600) (2186-1334-02)(-650) (2186-1335-01)(-650) (2186-1479-02)(-090,-100,-300,-600) (2186-1601-02)(-090,-100,-300,-600) (2186-1477-01) (2186-1317-01)(-650) (2186-1401-01)(-090,-100,-300,-600) (2186-0166-01) (2186-1609-01) (2186-1613-01) (2089-1607-02) (2089-1620-01) (2186-1333-02) (-650) (2186-1474-02) (-090,-100,-300,-600) (2089-1621-01) [2186-1603-01] (2186-1318-01) (-650) (2186-1403-02) (-090
(2186) 9 PART NAME 2186-0131-01 2186-0135-01 (2186-0166-01) [2186-1603-01] (2181-1305-01) (2186-1317-01) (2186-1401-01) (2186-1318-01) (2186-1403-02) (2186-1330-03) (2186-1469-04) (2186-1331-02) (2186-1470-01) (2186-1332-02) (2186-1473-02) (2186-1333-02) (2186-1474-02) (2186-1334-02) (2186-1479-02) (2186-1335-01) (2186-1601-02) (2186-1402-03) (2186-1404-01) (2186-1407-01) (2186-1410-01) (2186-1424-01) (2186-1471-01) (2186-1475-01) (2162-1477-01) (2186-1477-01) (2186-1481-02) (2186-1602-02) (2089-1607-02) (
2186-0131-01(-650) 2186-0135-01(-090,-100,-300,-600) (9372-3960-02) (2186-1443-01) (9747-1740-01)(3) (9747-1740-01)(4) (9384-2190-50) (5X5mm) (2186-1441-02) (2186-1476-01) (9384-2190-50)(3) (5X5mm) (9384-2191-00) (10X10mm) (9747-1745-01)(2) (2186-0146-01) (9384-2190-50) (3X6mm) (9384-2190-50) (5X5mm) (9384-2191-00) (10X10mm) (9761-2060-01)(2) A (9384-2190-50)(2) (5X5mm) (2186-1327-03) (-650) (2186-1440-03) (-090,-100,-300,-600) (2186-1320-03) (9761-2060-01)(2) (-650) (2186-1421-02) A (-090,-100
(2186) 10 PART NO PART NAME QTY.
(9767-1435-01) 2186-0121-01(-090,-100,-300,-600) 2186-0122-01(-650) (2186-1445-01) (2186-1446-01) (2186-1336-01) (-650) (2166-1485-01) (-090,-100,-300,-600) (9384-2290-90) (9X20mm) (2186-4511-01) (2186-1115-01) (2186-1119-02) (2186-1133-01) (2186-1132-01) (2186-1116-01) (2186-1133-01) (2186-1132-01) (2186-1329-03)(-650) (2186-1444-02)(-090,-100,-300,-600) (2186-1431-02) (2186-1106-01) 2186-0110-01 (2186-1107-01) (2186-1418-03) (2186-1417-02) (2186-1433-01) (2186-1430-03) (2186-1432-01) (9747-1
(2186) 11 PART NO PART NAME 2186-0110-01 BACK COVER ASSY QTY.
12 (2186) PARTS LIST WIRING DIAGRAM 1 (2186) ■LEAD WIRES LIST 2186-4401-01 (W 151) 2186-4402-01 (W 152) 2186-4403-01 (W 153) 2186-4404-01 (W 154) 9391-0807-□□ (W 5, 6, 7, 8, 9, 10, 11, 12, 13, 14) 9391-1207-□□ (W 1, 2, 3, 4, 15, 16) W11/BLACK W12/BROWN EYE PIECE FRAME ASSY (0134) W13/YELLOW W14/GREEN SLLK CONTACT A (1542) W7/BLACK AF CHARGE ASSY (0521) W8/ORANGE W10/ORANGE W9/GREEN AFM(+) BLUE GRAY POWER SUPPLY HARNESS (0441) ORANGE TOP COVER FPC ASSY (0407) DCDC PCB ASSY (0402) ENAMEL WIRE/
(2186) 1 REPAIR GUIDE This repair guide section contains the disassembly and adjustment procedures. For the assembly procedure, follow the reverse procedure.
2 (2186) ■ Precautions Chemicals Handle chemicals of high volatility with care, use of which will affect to your health and environment. 1. Store them sealed in a specific place to prevent exposure to high temperature or direct sunlight. 2. Avoid dividing them into small containers and prevent vaporization. 3. Keep containers sealed when not in use. 4. Avoid using them as much as possible. When required, remove only required amount from the container to make full use. REPAIR GUIDE Plastic parts 1.
(2186) 3 Discharge Before disassembly, be sure to discharge the main condenser in the following manner. WHITE YELLOW Short-circuit with discharger or resistor of 200-300 ohm/3w. Check voltage to make sure it is discharged. “ a” “ b” Cut I/O FLEXIBLE ASSY REPAIR GUIDE To activate without exterior parts Short-circuit the pattern -a of I/O FLEXIBLE ASSY with solder. When using replacement I/O FLEXIBLE ASSY, no need to short these patterns because it has pattern-b.
4 (2186) 1. Disassembly of the exterior parts Disassemble it in order of step 1to 8. 9747-1755-04(2)(-650) 9747-1755-15(2) (-090,-100,-300,-600) 2098-5045 9761-1470-01 5041 9611-2035-04(-650) 9611-2035-15 (-090,-100,-300,-600) 9744-1665-04(2)(-650) 9744-1665-15(2) (-090,-100,-300,-600) ⑤ TOP COVER ASSY ■ Fig. 2 See Page 27. 9744-1620-01 VERSION PLT C REPAIR GUIDE A ③ 9611-1625-01(2) ⑧ 9747-1740-04(-650) 9747-1740-15 (-090,-100,-300,-600) EYE PIECE FRAME ASSY ■ Fig.
(2186) 5 ■ Fig. 2 Removal the TOP COVER ASSY TOP COVER FPC ASSY TOP COVER ASSY ■ Fig. 1 Removal the BATTERY COVER ASSY BATTERY COVER ASSY Connector ■ Fig. 3 Removal the LCD 101 Connector SW FPC2 ASSY Connector LCD 101 ■ Fig. 4 Stick SW FPC 1 ASSY of 1001 1001 1001 SW FPC 1 ASSY 9384-2191-00 (10x10mm) 9384-2190-50 (5x5mm) ■ Fig.
6 (2186) REPAIR GUIDE ■ Wires arrangement
(2186) 7 REPAIR GUIDE
8 (2186) 2. Disassembly of the I/O FPC ASSY, MAIN PCB ASSY Disassemble it in order of step 1to 5. ③ 9747-1740-01 0441 ■ Fig. 3 1021 B DCDC PCB ASSY ■ Fig. 6, 7 D ② 4520 ■ Fig. 4 A I/O FPC ASSY ■ Fig. 1 REPAIR GUIDE 9747-1740-01 9384-2191-00(2) (10x10mm) ■ Fig. 2 9384-2191-00 (10x10mm) ■ Fig. 2 A D B 9384-2290-90 (5x20mm) ■ Fig. 5 2709 ■ Fig. 9 MAIN PCB ASSY 9744-1615-01 C 1175 C 1175 2708 ■ Fig. 11 1173 1735-15 9749-1735-15 9749■ Fig. 12 4514 ■ Fig.
(2186) 9 ■ Fig. 1 ■ Fig. 2 I/O FLEXIBLE ASSY 9384-2191-00 (10x10mm) Connector (2) 9384-2191-00 (10x10mm) REPAIR GUIDE ■ Fig. 3 ■ Fig. 4 POWER SUPPLY HARNESS Connector 4520 MAIN PCB ASSY ■ Fig. 6 ■ Fig.
10 (2186) ■ Fig. 8 ■ Fig. 7 DCDC PCB ASSY Connector MAIN PCB ASSY REPAIR GUIDE 4514 MAIN PCB ASSY ■ Fig. 10 ■ Fig. 9 2709 1172 ■ Fig. 12 ■ Fig.
(2186) 11 3. Disassembly of the SUB PLATE L, BATTERY CHAMBER Disassemble it in order of step 1 to 3. 9745-2025-01 9748-2050-01 9747-1735-01 9748-2050-01(2) SUS PLATE L 9745-2025-01(2) ② 5034 ■ Fig. 2 1005 9744-1625-01(2) 9748-2050-01 See Page 23. ③ 9748-2050-01 REMOTE FPC ■ Fig. 1 96112025-01(2) 0141 1146 9747-1735-01 5033 ■ Fig. 3 ① 9748-2050-01 ■ Fig. 4 See Page 13.
12 (2186) ■ Fig. 1 REPAIR GUIDE FPC of AF CHARGE ASSY FPC of AF MODULE ASSY FPC of SHUTTER ASSY REMOTE FPC ■ Fig. 2 ■ Fig. 3 5034 ■ Fig.
(2186) 13 4. Disassembly of the CCD ASSY, SHUTTER ASSY If CCD ASSY (0271) is exchanged for new one, exchange the bar code on the MAIN PCB ASSY (0410) for the bar code put on the new CCD ASSY. Disassemble it in order of step 1 to 4. CCD FPC ASSY ■ Fig. 1 9384-2190-50 (3.5x10mm) ■ Fig. 4 2181-2920 ■ Fig. 5 9748-2055-01 9747-1745-01(4) CCD ASSY ② 2181-2918 9758-0100-00 2961 ■ Fig.
14 (2186) ■ Fig. 2 ■ Fig. 1 1171 2961 REPAIR GUIDE 2721 ■ Fig. 4 ■ Fig. 3 SLIDER ASSY 2937 CCD CONECTING FPC Flexible of CCD ASSY ■ Fig.
(2186) 15 SHUTTER ASSY Installation 1. Supply power to the charge motor at 2V/1A to drive it normally until the mirror raises completely. DC Power Supply (2V, 1A) 2. Insert screw driver into the hole of“SHUTTER CHARGE GEAR”, and put“SHUTTER ASSY” by holding the screw driver at the 90 degrees position shown on the picture.
16 (2186) REPAIR GUIDE ■ CCD inclination adjustment / repair Check Setup the equipments so that the camera faces to a subject at accurate level; 1. Use a copy stand or place a mirror on the wall. 2. Use a 50/1.7 lens for inspection. 3. Measure an angle of gradient by Photoshop. If it is beyond +/- 1.0 degree, be sure to implement the Repair method (mentioned later). If it is between +/- 0.5 and +/- 1.0 degree, implement the Repair method (mentioned later) upon request of the user. If it is within +/- 0.
(2186) 17 5. Disassembly-1 of the MIRROR BOX ASSY Disassemble it in order of step 1 to 6. ③ 5022 ■ Fig. 2 TOUKO ASSY ④ INF LCD HOLDER ASSY ② 5048 ■ Fig. 1 9747-1745-01(3) 9384-2290-90 (9x15mm) ■ Fig. 1 9747-1745-01(2) 97471735-01(2) ⑥ PENTA ASSY DIOPTER ASSY 9747-1745-01(2) ① See Page 19. SI SCREEN VB WASHER FRESNEL 9384-2190-50 (3x5mm) ■ Fig.
18 (2186) ■ Fig. 1 ■ Fig. 2 9384-2290-90 (9x15mm) 5022 REPAIR GUIDE 5048 ■ Fig.
(2186) 19 6. Disassembly-2 of the MIRROR BOX ASSY Disassemble it in order of step 1 to 5. 2533 9747-1750-01 2532 See Page 22. APERTURE ASSY See APERTURE ASSY Setting (pg. 21) ⑤ 2512 2533 9747-1750-01(2) ② 1524 REPAIR GUIDE APERTURE RING See APERTURE RING Removal/Installation (pg. 21) 2181-5123 2535 2534 1511 2163-1521 1813 1522 2532 9747-1745-01 2181-5123 9749-1730-01 1523 ■ Fig.
20 (2186) ■ Fig. 2 ■ Fig. 1 REPAIR GUIDE COUPLER LEVER COUPLER LEVER SP AF CHARGE ASSY Installation 1. Rotate the designated cam-gear in arrow direction while keep pushing the lever against it until the lever descends down to the lowest. 2. Arrange the wires.
(2186) 21 APERTURE RING Removal/Installation Removal Turn APERTURE RING clockwise until it stops (Fig. 4). Now the ring can be removed. Be careful not to turn the aperture coupling gear in APERTURE ASSY. Installation 1. Set APERTURE ASSY to the charge completion position (default position) referring APERTURE ASSY setting procedure as shown below, then install to FRONT FRAME ASSY.
22 (2186) 7. Disassembly-3 of the MIRROR BOX ASSY Disassemble it in order of step 1 to 4. 5110(2) 9769-1730-01(2) BL CONTACT HOLDER ASSY 9769-1740-01 REPAIR GUIDE ③ 1812 9769-1740-01 0515 ■ Fig. 6 ④ 5109 ■ Fig. 1 0514 ■ Fig. 5 5806 B B-50 (After installation, allow to dry for 8 - 12 hours.) FRONT FRAME ASSY 2181-5108 ② 5107 ■ Fig.
(2186) 23 ■ Fig. 1 ■ Fig. 2 5108 5109 ■ Fig. 4 ■ Fig. 3 MAIN MIRROR DRIVING LEVER REPAIR GUIDE 5108 5107 MIRROR DRIVING LEVER MIRROR DRIVING LEVER ■ Fig. 5 ■ Fig.
24 (2186) 8. Disassembly of the BATTERY CHAMBER, LCD 101 Disassemble it in order of step 1 to 4. ① 9761-2055-01 9384-2290-90 (9x15mm) ■ Fig. 4 1088 ■ Fig. 4 9747-1740-01 9749-2035-01(2) 9384-2191-00 (6x20mm) CF CARD COVER 9769-1730-01 1153 1002 1159 ■ Fig. 3 1065 REPAIR GUIDE 1156 GYRO FPC ASSY ■ Fig. 5, 6 ① 9747-1735-01 0154 0155 9747-1735-01 BATTERY 4508 CHAMBER 9747-1740-01 1086 9747-1750-01 1072 1087 ■ Fig. 7 1082(2) ■ Fig. 7 9747-1730-01(2) FLASH PCB ASSY 1083 ■ Fig.
(2186) 25 ■ Fig. 2 ■ Fig. 1 1081 1083 ■ Fig. 4 ■ Fig. 3 1159 1088 9384-2290-90 (9x15mm) 1087 ■ Fig.
26 (2186) ■ Fig. 6 GYRO FLEXIBLE ASSY 1002 REPAIR GUIDE ■ Fig. 7 1087 1073 ■ Fig.
(2186) 27 9. Disassembly of the TOP COVER ASSY Disassemble it in order of step 1 to 11. (Continued to the next page) 9747-1745-04(2)(-650) 9747-1745-15(2)(-090,-100,-300,-600) MODE DIAL NAME PLATE FLASH CASE (UPPER) ⑤ 1477 MODE DIAL 0166 ■ Fig. 4 MODE DIAL DECORATION 2089-1607 2089-1620 ⑩ ⑦ 1609 ■ Fig. 5 ⑧ RING 1603 ■ Fig.
28 (2186) BUZZER 9747-1740-01(3) 9747-1740-01(4) 1443 9384-2190-50 (5x5mm) 1476 1441 9384-2190-50(3) (5x5mm) 9384-2191-00 (10x10mm) 9747-1745-01(2) 9384-2190-50 (3x6mm) REPAIR GUIDE 0146 9384-2191-00 (10x10mm) ② ■ Fig. 2, 3 A 9384-2190-50(3) (5x5mm) 9761-2060-01(2) ① 1625 ■ Fig.
(2186) 29 ■ Fig. 1 1611 PU DETECT CONTACT MODE DIAL PLATE 9384-2190-50(3) (5x5mm) 9384-2190-50(3) (5x5mm) 9384-2190-50 (5x5mm) TOP COVER FPC ASSY WB DIAL BASE PLATE 9384-2191-00 (10x10mm) 9384-2191-00 (10x10mm) ■ Fig. 3 FRONT DIAL HOLDER ASSY TOP COVER FPC ASSY REPAIR GUIDE ■ Fig.
30 (2186) REPAIR GUIDE ■ Fig. 4 B B-110 ■ Fig.
(2186) 31 10. Disassembly of the FRONT COVER ASSY, BACK COVER ASSY 9767-1435-01 1445 ■ Fig. 1 1446 ■ Fig. 1 4511 9384-2290-90 (9x20mm) 1115 PREVIEWBUTTON REPAIR GUIDE 1133 1132 1116 1133 1132 1119 AF/M CHANGEOVER LEVER 1106 1107 G G-115 (Slide part) 1431 1433 1430 1418 1432 1417 1143 9747-1740-01 2181-1419 ■ Fig. 2 1420 ■ Fig.
32 (2186) REPAIR GUIDE ■ Fig. 1 G G-85 ■ Fig.
(2186) 33 Required adjustment, setting and confirmation items after repairing(exchanging parts) Adjust, set and confirm as the following table when the following parts are removed (exchanged). Follow the steps from the upper line to adjust.
34 (2186) Related adjustment and required setting items When each adjustment or setting is operated, be sure to follow the related adjustment and setting items listed blow. Number : Related adjustment items. Adjust and set in order of the number. × : Related adjustment items. However, these items mean not to adjust the adjustment order is different (the adjustment should be completed). None : Unrelated adjustment and setting items (possible to adjust and set solely).
(2186) 35 Viewfinder Back Adjustment Equipment Required 1000mm Collimator AE Master Lens Magnifier Adjustment 1. Set up the camera as in Fig. 1, so that the chart is at the center of viewfinder. 2. Set Master Lens to infinity. 3. Check that the chart is in focus. If not, Select one or two VB Washers, and install Washer(s) as in Fig. 2. In case of front focus: Make VB Washers thinner. In case of rear focus: Make VB Washers thicker. ■ Fig. 1 Master Lens 1000mm Collimator ■ Fig.
36 (2186) Preparing the 2186 adjustment program 2186 Adjustment Program CD enables adjustment of both 2186 and 2181 PC for use The PC loaded on either Windows 98/98SE, 2000 Professional or XP and USB terminal originally 40MB or more of available memory and 15MB or more of available hard-disk space VGA or more monitor capable of displaying at least 32,000 colors Details of the 2181 adjustment program CD 2 1 8 6 a d ju s t m e n t p r o g r a m C D U S B 2 .0 u u s b d .d ll u u s b d .in f u u s b d .
(2186) 37 Starting up the 2186 adjustment program (in the adjustment mode). Fig.1 Fig.2 Quitting the 2186 adjusting program and cancel adjustment mode of camera 1. Click "ADJUSTMENT END" in the window of the 2186 adjustment program. 2. Remove the AC adapter or battery.
38 (2186) Adjustment of the PI-PR Required equipment PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 Procedure of the adjustment 1. Set camera to adjustment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2. Click "PI-PR" of the adjustment menu. "Does it adjust?" appears. 3. Click "YES". Automatic adjustment starts. 4. The adjustment is completed when "OK" is displayed on the adjustment menu.
(2186) 39 Adjustment of the gyro for camera shaking (GYRO) Required equipment PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 Procedure of the adjustment 1. Set camera to adjustment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2. Click "GYRO" of the adjustment menu. "Does it adjust?" appears. 3. Click "YES". Automatic adjustment starts. 4. The adjustment is completed when "OK" is displayed on the adjustment menu.
40 (2186) Setting for the adjustment of CCD AORI & CENTER Required equipment PC with preinstalled the 2186 adjustment program Master body (Mass Production camera of 2186) AE Master Lens 2181 AORI-Chart Hexangular wrench (1.5) or hexangular screwdriver Fluorescent light stand SQ967W Tripod USB-2 (USB cable) AC Adapter AC-11 Grip Ring Setting the Master body and the chart 1. Setting all equipment according to the order listed below (Fig. 1). REPAIR GUIDE Caution: Use stable tripod.
(2186) 41 Adjustment / Checking of CCD AORI & CENTER Outline Peform adjustment of CCD position and perspective. *See Setting the camera and the chart when adjusting the CCD AORI&CENTER (P. 40). With 2186 adjustment program, master body for CCD Aori & Center is selectable from 2181 and 2186. Preparation of the adjustment *When CCD sensor module is out of position after replacing CCD MODULE ASSY, tighten three AORI adjusting screws until they stop, then evenly loosen them by 3 turns. 1.
42 (2186) ■ Fig. 3 ■ Fig. 1 ■ Fig. 2 REPAIR GUIDE ■ Fig. 4 Numbers mean the degrees of rotating adjusting screw Arrows mean the direction of rotating adjusting screw Procedure of CCD AORI checking 1. Set 2186 camera to adjustment mode. Refer to“Starting up the 2181 adjustment program (in the adjustment mode)”in P. 37. 2. Click“AORI & CENTER”in adjustment menu. 3. Click“2186”when“Please select master data”appears. (Fig. 1) 4. Click MASTER BODY“AORI & CENTER”in AORI & CENTER Adjustment menu(Fig.
(2186) 43 Manual Set SS & X-Sync. Time-lag Check Equipment Required Shutter Tester AC Adapter AC-11 X CableⅡ or X Cable , AEF SIGNAL ADPTER Ⅳ, BODY SIGNAL ADAPTER( with X contact) Manual SS Check 1. Set up the equipment as in Fig. 1. 2. Release the shutter at each shutter speed, and check that reading meets the table-1 below. X Sync. Time-Lag Check 1. Set up the equipments as in Fig. 1 or as in Fig.2. 2. Release the shutter and check that reading meets the table-2 below. ■ Fig.2 ■ Fig.
44 (2186) Adjustment Manual Set SS Equipment Required PC with preinstalled the 2186 adjustment program Shutter Tester USB-2 (USB cable) AC Adapter AC-11 REPAIR GUIDE Procedure of the adjustment 1. Set camera to adjustment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. *Turn off the AS switch. 2. Click“SS”of the adjustment menu. “Does it adjust?”appears. Click“YES”. 3.“Execute 1st release?” appears. Click“OK”. 4.
(2186) 45 Preparation before AF adjustment Note: After replacing CCD MODULE ASSY and/or MIRROR BOX ASSY or its relative parts, always perform AF Area Adjustment (pg. 46) to EZ Adjustment (pg. 49). If customer says focus fucntion is not normal, perform this adjustment too. Preparations The following items should have been completed before starting AF adjustment. 1. Peform this adjustment without FRONT COVER ASSY, after disassemble. 2.
46 (2186) AF Area Adjustment Adjustment 1. Set up the equipment as in Fig. 1. 2. Set the camera to the adjsutment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 3. Click“AF”of the adjustment menu.“Does it adjust?”appears. 4. Click“YES”.“Please select menu”appears. 5. Click“AREA”and then click“START”. Automatic adjustment starts and displays waveform and readings. Check that each line has two dents like the ones in Fig.
(2186) 47 Pitch Yaw Adjustment Turn a flood lamp toward camera during Pitch Yaw Adjustment. Adjustment Pitch Adjustment 1. Set camera to adjustment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2. Attach AF-Y/P Adjuster to the camera, and set Pitch Adjusting Plate as in Fig. 1. 3. Click“AF”of the adjustment menu.“Does it adjust?”appears. 4. Click “YES”. “Please select menu” appears. 5. Click“PITCH/YAW”and then click“PITCH”. Automatic adjustment starts. 6.
48 (2186) FLATNESS Adjustment *Select the island and wave form after the flatness adjustment enables dust check. Required equipment Luminance box ( L-2101/L-2111 or multi camera tester: EF-8301 ) AE Master Lens PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 REPAIR GUIDE Procedure of the adjustment 1. Set camera to adjustment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2.
(2186) 49 EZ Adjustment Be sure to perform the adjustment for all island groups in series according to the display after replacing CCD MODULE ASSY. Adjustment 1. Set up the equipment ( refer to P. 48 Fig. 1 , Fig. 2). 2. Set the camera to the adjsutment mode. Refer to “Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 3. Click“EZ”of the adjustment menu.“Please select menu”appears. 4. Click “ADJUST”. 5.“Does it adjust?”appears. Click“YES”.
50 (2186) EZ Check Check 1. Set the camera to the adjsutment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2. Click“EZ”of the adjustment menu.“Please select menu”appears. 3. Click “CHECK”. (Fig. 1, Fig. 2) 4.“Please select island”appears. Align the focus frame on the island to be checked. Use the appropriate chart according to the desired island group. (See table below) 5. Click the island to check. EZ value is displayed. (Fig. 2) 6.
(2186) 51 EZ SHIFT Decide the amount of shift by getting the average of 4 points of each island. Island group 3rd(3), 4th(4,5,6), 6th(8) 5th(7) 1st(1), 7th(9) 2nd(2), 8th(10) ISLAND ISLAND ISLAND ISLAND Chart AF Chart-I for 2163 (Horizontal) AF Chart-I for 2163 (Vertical) AF Chart-II for 2163 (Horizontal) AF Chart-II for 2163 (Horizontal) * Measuring point A-D E-H I-L M-P When checking the reading at 2nd island group and 8th island group, use AF Chart-II for 2163 upside down. Procedure 1.
52 (2186) Aperture Preset Check / Adjustment Equipment Required PC with preinstalled the 2186 adjustment program HIT I/O Tester Preset Signal Adapter USB-2 (USB cable) AC Adapter AC-11 Check 1. Set up the equipment as in Fig. 1, and set camera to“M”mode and“Bulb”. 2. Press Reset Button on HIT I/O Tester so that“00”appears in the display. 3. Set aperture to f/11, and release the shutter. Check the reading in HIT I/O Tester is within the standard.
(2186) 53 Check / Adjustment of the AE (AE) Required equipment Luminance box L-2101/L-2111 or multi camera tester: EF-8301 AE Master Lens PC with preinstalled the 2181 adjustment program USB-2 (USB cable) AC Adapter AC-11 ■ Fig. 1 Procedure of the Adjustment 1. Set the camera to the adjsutment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. Attach the AE Mater lens to the camera, and then set to the adjustment mode.
54 (2186) Sensitivity adjustment (CCD GAIN) Required equipment Luminance box L-2101/L-2111 or multi camera tester: EF-8301 AE Master Lens PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 Procedure of the adjustment 1. Set camera to adjustment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2. Set the camera and the measuring instrument as shown on the Fig. 1. 3. Set the brightness of the Luminance box to EV 7. 4.
(2186) 55 Adjustment of white balance (WB) Required equipment Light Source-A. Refer to Light source-A maintenance, P. 59. Light balancing filter LB200 Master body (Mass Production camera of 2186) AE Master Lens PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 White chart Grip Ring ■ Fig. 1 White Chart White ChartLight Source A: Refer to Ligh Source A maintenance, P.59 ■ Fig. 2 REPAIR GUIDE Procedure of the adjustment 1. Set Master body to adjustment mode.
56 (2186) Adjustment of the camera shaking compensation (SHAKE GAIN) REPAIR GUIDE Required equipment Vibration tester Shake Offset Chart 2 PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 Master Lens for SHAKE Preparation of the adjustment 1. Set the camera without USB cable and the measuring instrument as shown on the Fig. 1. Set distance between camera and Shake Offset Chart 2 to 1600mm.
(2186) 57 FLASH LEVEL SHIFT This adjustment is to shift the flash level optionally. Equipment Required PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 Procedure 1. Set the camera to the adjsutment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2. Click“FLASH LEVEL”in the adjustment menu. “Does it adjust?”appears. 3. Click“YES”. “Please input Type and Shift”appears. (Fig. 1) 4.
58 (2186) CAMERA LOG Equipment Required PC with preinstalled the 2186 adjustment program USB-2 (USB cable) AC Adapter AC-11 Procedure 1. Set the camera to the adjsutment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in P. 37. 2. Click“CAMERA LOG”in the adjustment menu. The following items can be read out and cleared.
(2186) 59 Light Source-A Maintenance OutLine Because high accuracy of required light source-A is required when adjusting and confirming. Measuring instrument Chroma meter (CL-200) Liminance meter (LS-100) Light source-A (tungsten light) Procedure *Managements of the chromaticity and the luminance 1. Light the light source-A on. 2. Measure the chromaticity coodinate (x,y) with the chroma meter. (Fig. 1) Fig.1 REPAIR GUIDE 3. The result should be within the range of the following table.
60 (2186) Error code on adjustment program Error Code List of PC Adjustment program Discription about adjustment NG Code ＮＧ Ｃｏｄｅ： ０ｘ００００００００ 1) Compare to the standard value 00 : Greater than standard value 01 : Smaller than standard value 2) Step number of adjustment sequence 00 ∼ ff : Sequence number REPAIR GUIDE 3) ＮＧ item nubmer Refer to the nexe page 4) Adjustment Item [ 0* ] Before adjustment process 00 : Initialization, reading version Info., etc.
(2186) 61 Adjustment（Common） **f1**** USB port initialization is not good. **f2**** USB port initialization is not good. **f3**** Reset of ANIT-SHAKE is not good. **f4**** Reset of ANIT-SHAKE is not good. **f5**** Camera ver. Readout is not good. **f6**** Camera ver. Readout is not good. **f8**** Tmp. data read is not good. **f9**** Tmp. data read is not good. **fb**** Setting of Camera mode is not good. **fc**** Setting of Camera mode is not good. **fe**** Access of Flash ROM is not good.
62 (2186) REPAIR GUIDE Measuring instrument PC (AT convertible) with preinstalled Windows 98, 98SE, 2000 or XP. (USB port should be guaranteed its performance by the maker. Also, Adobe Photoshop 6.0 or later should be installed if Windows 2000 or XP is installed on PC.) * It is possible to confirm the performance on PC with Windows 95 (AT convertible). (Card reader and PC card adapter are required.
(2186) 1 TROUBLESHOOTING CHART This section consists of the following items.
2 (2186) Trouble code (1)Check Equipment required PC with 2186 adjustment program installed USB-2 (USB cable) AC-11 Procedure 1. Set camera to adjustment mode. Refer to“Starting up the 2186 adjustment program (in the adjustment mode)”in pg. 37 of Repair guide. 2. Click“CAMERA LOG”of the adjustment menu. (Fig. 1) Check the items in the CAMERA LOG dialog. (Fig. 2) ■ Fig. 1 TROUBLE-SHOOTING CHART ■ Fig. 2 ERROR CODE: SHOOT: FLASH: Refer to the error code list (listed in hex).
(2186) 3 (2)Trouble Code List Major Cause Camera Operation code Condition 50 SCAM2 never become OFF within 150ms after charge motor Charging mechanism NG. driving on mirror up. After all motors brake for 50ms, system down. 52 FP pulse number is short more than 32 pulse after aperture stabilized. 53 SCAM1 never become ON within 2s after charge motor driving on charging. 54 SCAM2 never become ON within 2s after charge motor driving on charging.
4 (2186) Trouble Code List Major Cause Camera Operation TROUBLE-SHOOTING CHART code Condition 30 Bilt-in flash charging error. (charging cannot finish within 30s) Fuse has blown. Flash charging circuit has damaged. IGBT NG. After all motors brake for 50ms, system down. 31 Built-in Flash cannot fire. Fuse has blown. Flash charging circuit has damaged. IGBT NG. ↑ 32 Bilt-in flash charging error. (voltage cannot reach 50V within 5s) Fuse has blown. Flash charging circuit has damaged. IGBT NG.
(2186) 5 TROUBLE-SHOOTING CHART
TROUBLE-SHOOTING CHART 6 (2186)
(2186) 7 TROUBLE-SHOOTING CHART
TROUBLE-SHOOTING CHART 8 (2186)
(2186) 9 TROUBLE-SHOOTING CHART
(2186) 1 Check List 1. This Check List describes the quality of operation warranted to general users. When users inquire about quality or request inspection, refer to this Check List. Use this list also when checking operation after repair. 2. When using this list during shipping or receiving inspection, judge the quality according to the purpose of the inspection, not by directly referring to this level. 3.
2 (2186) Condition of Measure and Appreciation Basically maesure and appreciation at the blow condition. But it is allowed to use another condition as long as not to influence the examination results. (The concrete settings refer to the opelationmanuals of the PC or monitor.) 1. Settings of Screen Area and Colors (System settings of PC) Macintosh 17 inch type monitor 1024x768 pixels Screen Area 20 inch type monitor 1152x870 pixels 16.
(2186) 3 3.Image cache memory setting Edit ‐ Preferences - Memory & Image cache...‐ Check off“Use cache for histgrams” Screen Dust 1. Measure Equipment: Photoshop 2. Capture Condition: Light source Illumination Lens Capture Distance Exposure Mode WB Focus Image Size Compression Mode Luminance Box EV10 2613 Stick a lenz to a luminance box. A mode (F11) Preset ( A light source) ∞ position 3008x2000 (L) Fine or Std. 3. How to measure: 1). Stick to a luminance box and capture, and open in PC. 2). with 33.
4 (2186) Standard Exposure Manual Shutter-speed ManualShutter-speed Period Tolerance SS (ms) (ms) 1/4000 0.244 0.156 - 0.383 1/2000 0.488 0.333 - 0.714 1/1000 0.977 0.793 - 1.202 1/500 1.950 1.590 - 2.40 1/250 3.910 3.17 - 4.81 1/125 7.810 6.35 - 9.62 1/60 15.60 12.7 - 19.2 1/30 31.30 29.2 - 33.5 1/15 62.50 58.3 - 67.0 1/8 125 117 - 134 1/4 250 233 - 268 1/2 500 467 - 539 X-sync Time Lag Allowable range With in 0.45EV With in 0.
(2186) 5 Check 1. Insert the CF card in the cart slot of the camera, and set the camera on the tripod. 2. Set up the equipment and distance as shown on the following table. Image size Compression Mode Exposure Mode Focus Mode Flash Mode Distance 3008x2000 (L) or 2256x1496 (M) Fine or Std. A mode (Aperture full open) Auto Focus Cancell Approx. 3m (Using Standard lens 2613) 3. Capture the charts (for Wide-angle) at the when focusing from both ∞ and near end for 5 times.
6 (2186) Image quality CHECK LIST Check Grayscales and Color Reproduction to verify performance. Capture images with the given condition and save them to a computer, and then read the color data with the Color Calculator 2 (2766-0008-75). Color Calculator 2 Installation 1. Load the Color Calculator 2 CD-ROM to the computer. 2. Click on English folder in the CD-ROM. 3. Double-click on SET UP.exe. The installer program starts automatically. 4.
(2186) 7 Grayscales MeasuringCondition Chart: Macbeth Color Checker Light Source: Light Source-A (Tungsten) 6500+/-100 lux. Lens: Attach the lens (#2163) be sure to set the chart right in front of the camera so that the chart center aligns with the optical axis. Distance (from the subject): 1.5m Focus: MF (1.5m) WB: Preset A light source Image size: 3008x2000 (L), 2256x1496 (M) or 1504x1000 (S) Compression Ratio: Std.
8 (2186) Current Leak Main Switch Current leak (7.4 volts/ 3 A) (Using Power Supply Adapter <2755-0005-75> Standard OTP Mask Item OFF 100 micro A or below Back LCD APO status 300 mA or below ON Standby status 700 micro A or below 450 micro A or below BC Lock voltage CHECK LIST BC lock voltage (Using Power Supply Adapter for 2766 <2766-0013-76>) Item Standard Lock 6.8V (With attachment black plug) Unlock 7.4V (With 0.
Page １ 2186 Supplementary Information Index Division Camera CS Division Issued December 08, 2005 Approved by Verified by Yata Issued/Code/Version/Page Title ’05.09.15 QS FA2186-S01E 1 ’05.09.22 QS FA2186-S02E 2 ’05.09.22 QS FA2186-S03E ’05.10.
(2186) SERVICE MANUAL SUPPLEMENTARY 1 No. QS FA 2186-S01E Sep.. 2005 CODE NO. 2186 Series MODEL DYNAX 5D MAXXUM 5D α SWEET DIGITAL α 5 DIGITAL INFORMATION Handling instructions on static electricity of Position detection assy (Slider Assy: 3261-0911) About Position detection assy: Position detection assy is sensitive to static electricity. Keep this parts under 50V. Symptom: CCD center adjustment (CENTER) cannot be done. Error occurs.
(2186) 2 SERVICE MANUAL SUPPLEMENTARY No. QS FA 2186-S02E Sep. 2005 CODE NO. 2186 Series MODEL DYNAX 5D MAXXUM 5D α SWEET DIGITAL α 5 DIGITAL INFORMATION External flash control Treatment on underexposure by #2181 with external flash 1) External flash adjustment to lower pre-flash level (no service information issued) 2) Camera adjustment to amplify final flash level by firmware upgrade and 1). (cf. Supplementary Information No.
(2186) SERVICE MANUAL SUPPLEMENTARY 3 No. QS FA 2186-S03E Sep. 2005 CODE NO. 2186 Series MODEL DYNAX 5D MAXXUM 5D α SWEET DIGITAL α 5 DIGITAL INFORMATION Repair information for a blooming image Conditions The blooming generates on the scene that the light-dark difference is large and which has a bright part on a dark part. Cause The value of V-sub voltage is wrong. Repair method 1. Check the bar code on a main PCB board assy, and conduct the CCD Vsub voltage adjustment. (VSUB) 2.
(2186) 4 SERVICE MANUAL SUPPLEMENTARY No. QS FA 2186-S04E Oct. 2005 CODE NO. 2186 Series MODEL DYNAX 5D MAXXUM 5D α SWEET DIGITAL α 5 DIGITAL INFORMATION Firmware Installation Install firmware after replacing the MAIN PCB ASSY (#2186-0410). Equipment required Firmware Ver.1.00 for 2186 <2186-0002-75> *Available at Camera CS Information Site. Firmware update 1. Decompress the Firmware Ver.1.00 for 2186 file. 2. Copy the five files (dsc.app, dsc.brd, dsc.brm, dsc.cam, ram.
(2186) SERVICE MANUAL SUPPLEMENTARY 5 No. QS FA 2186-S05E Nov. 2005 CODE NO. 2186 Series MODEL DYNAX 5D MAXXUM 5D α SWEET DIGITAL α 5 DIGITAL INFORMATION Battery charge prevention using AC-11 Symptom: If the AC-11 is connected in the condition that a battery is in the camera, the following symptom will occur depending on the battery capacity. Battery will be charged. Battery will be exhausted. The repair method: Remove W16/BLACK.
(2186) 6 SERVICE MANUAL SUPPLEMENTARY No. QS FA 2186-S06E Dec.. 2005 CODE NO. 2186 Series MODEL DYNAX 5D MAXXUM 5D α SWEET DIGITAL α 5 DIGITAL INFORMATION Initial repair information SUPPLYMENTARY INFORMATION symptom Cause Measure Unexposure at the first time after leaving for a certain period. (Error 58) Pressure to the Shutter assy cam roller was applied for a certain period.
(2186) symptom 7 Cause Measure Abnormal LCD display 101 LCD harness (red) was caught between chassis Unclip LCD harness (2186-0442). LCD sometimes blinks. Eye-detection failure (unmodified body) Measure will be informed by PML as soon as the parts are ready. Camera does not start. Disconnecion of the Fuse (F002) on DCDC PCB assy. After replacing the DCDC PCB assy, the symptom did not recur.
(2186) 8 symptom SUPPLYMENTARY INFORMATION Cause Measure Eject connector (93830561-50) exchange CF card cannot be inserted fully. Metal plate and a lever link component interfere. A parting part and a lever link component interfere. At the time of reappearance, it is in the state where CF card was inserted, and when pushing eject button and taking out a card, a finger is touching so that it may support CF card. It recurs in the timing.
(2186) symptom Exposure mode dial and WB dial failure. Shutter release failure (stays S2 ON). Self LED stays lighting. Flash UP is not detected. 9 Cause Measure I/O FPC cover was scratched by the main chassis I/O FC assy (2186-0406) edge, and short-circuit with the internal pattern. exchange Black lead wire was crushed under the shoe plate by the assembly-operation mistake. R606 and R607 on the top cover FPC were burned and damaged.
Parts Modification List About the written contents of a PARTS MODIFICATION LIST. Description for each item in PML. (1) Code number of the model and page number. (2) Reference No.. (3) Relevant page of Parts List. (4) Reference No. of its creation post is shown. (5) Number of relevant Supplementary Information if any. (6) Reason of modification. (7) Models in which the part is used in common. (8) Previous parts number. (9) New parts number.
(2186) REF No. 管理No. 1 PARTS MODIFICATION LIST QS FA 2186-P001 Camera CS Division Division カメラCS部 主管部署 Valid from October 11. 2005 施行年月日 Parts List P.
(2186) REF No. 管理No. 2 PARTS MODIFICATION LIST QS FA 2186-P002 Camera CS Division Division カメラCS部 主管部署 Valid from October 25. 2005 施行年月日 Parts List P.
(2186) REF No. 管理No. 3 PARTS MODIFICATION LIST QS FA 2186-P003 Camera CS Division Division Approved by Verified by Written by 承認 審査 作成 カメラCS部 主管部署 Valid from November 02. 2005 Yata Ueno 施行年月日 Parts List P. 8, 12 SUPPLEMENTARY INFORMATION No.
(2186) REF No. 管理No. QS FA 2186-P004 PARTS MODIFICATION LIST Camera CS Division Division カメラCS部 主管部署 Valid from November 07. 2005 施行年月日 Parts List P.
(2186) REF No. 管理No. 5 PARTS MODIFICATION LIST QS FA 2186-P005 Camera CS Division Division カメラCS部 主管部署 Valid from January 17. 2006 施行年月日 Parts List P.
(2186) REF No. 管理No. 6 PARTS MODIFICATION LIST QS FA 2186-P006 Camera CS Division Division カメラCS部 主管部署 Valid from January 17. 2006 施行年月日 Parts List P.
(2186) REF No. 管理No. 7 PARTS MODIFICATION LIST QS FA 2186-P007 Camera CS Division Division カメラCS部 主管部署 Valid from January 17. 2006 施行年月日 Parts List P. 8 REASON サービス供給として設定する 変更理由 To supply as a spare part 2186-0473-01 Previous ―――――― Previous Approved by Verified by Written by 承認 審査 Yata 作成 Ueno 仮-976 COMMON MODEL 共通機種 →― →― ―← ―← 2186-Series 2186-0473-01 (9346-3361-01) New New 2186-0473-01 PML (9346-3361-01) FUSE ヒューズ A d d e d .
(2186) REF No. 管理No. 8 PARTS MODIFICATION LIST QS FA 2186-P008 Camera CS Division Division カメラCS部 主管部署 Valid from January 17. 2006 施行年月日 Parts List P. 2 REASON サービス供給として設定する 変更理由 To supply as a spare part 2186-0402-03 Previous ―――――― Previous ―――――― Previous Approved by Verified by Written by 承認 審査 Yata 作成 Ueno 仮-974 COMMON MODEL 共通機種 →― →― →― ―← ―← ―← 2186-Series 2186-0402-03 (2186-4901-01) (2186-4902-01) B 2186-0402-03 (2186-4901-01) FUSE (F001) ヒューズ A d d e d .
(2186) REF No. 管理No. 9 PARTS MODIFICATION LIST QS FA 2186-P009 Camera CS Division Division カメラCS部 主管部署 Valid from February 28 2006 施行年月日 Parts List P. 6, 7 Approved by Verified by Written by 承認 審査 作成 Yata Ueno 2072-1242, 2181-1143 REASON 欧州におけるRoHS規制への対応 変更理由 Compliance with RoHS in Europe (2186-0150-01) →〇 Previous (2181-5123-01) →〇 Previous COMMON MODEL 共通機種 ×← ×← 2186-Series (2186-0150-02) (2181-5123-02) New New Page 7. (2186-0150-01) (2186-0150-02) Page 6.
(2186) REF No. 管理No. QS FA 2186-P010 10 PARTS MODIFICATION LIST Camera CS Division Division カメラCS部 主管部署 Valid from February 28 2006 施行年月日 Parts List P. 2, 4 REASON 欧州におけるRoHS規制への対応 変更理由 Compliance with RoHS in Europe 2186-1173-01 →〇 Previous 2181-2706-01 →〇 Previous Approved by Verified by Written by 承認 審査 作成 Yata Ueno 2186-1116, 2186-1139 COMMON MODEL 共通機種 ×← ×← 2186-Series 2186-1173-02 2186-2706-02 A D B Page 2. 2186-1173-01 2186-1173-02 Page 4.
(2186) REF No. 管理No. QS FA 2186-P011 PARTS MODIFICATION LIST Camera CS Division Division カメラCS部 主管部署 Valid from February 28 2006 施行年月日 Parts List P.
