2186_D5D_cvr_OM_GB_r4r.qxd 13.07.2005 17:23 Uhr Seite 2 Konica Minolta Customer Support: www.konicaminoltasupport.com Konica Minolta Photo World: www.konicaminoltaphotoworld.com Become a member of Konica Minolta Photo World today, free of charge, and enter the fascinating world of Konica Minolta photography. Register now, save 29.99 EUR, get DiMAGE Messenger for free! © 2005 Konica Minolta Photo Imaging, Inc. under the Berne Convention and the Universal Copyright Convention.
QUICK START CHECK LIST BEFORE YOU BEGIN The following sections will get you started in enjoying your camera. Thank you for purchasing this Konica Minolta digital camera. Please take the time to read through this instruction manual so you can enjoy all the features of your new camera. Attach a lens (p. 18) and the camera strap (p. 19). Adjust the viewfinder diopter if necessary (p. 19). Check the packing list before using this product. If any items are missing, immediately contact your camera dealer.
FOR PROPER AND SAFE USE GENERAL PRODUCT WARNINGS AND CAUTIONS NP-400 LITHIUM-ION BATTERIES Read and understand the following warnings and cautions for safe use of the digital camera and its accessories. This camera operates on a powerful lithium-ion battery. Misuse or abuse of the lithium-ion battery can cause damage or injury through fire, electric shock, or chemical leakage. Read and understand all warnings before using the battery. DANGER • Do not short, disassemble, damage, or modify the battery.
• Do not look at the sun or strong light sources through the viewfinder or lens. It may damage your eyesight or cause blindness. • Do not use these products in a humid environment, or operate them with wet hands. If liquid enters these products, immediately remove the battery or unplug the product, and discontinue use. The continued use of a product exposed to liquids may cause damage or injury through fire or electric shock.
TABLE OF CONTENTS Quick start check list .............................................................................................................................2 Before you begin....................................................................................................................................3 For proper and safe use ........................................................................................................................4 Names of parts .................................
Recording menu...................................................................................................................................70 Navigating the recording menu ...............................................................................................70 Image size and image quality..................................................................................................72 Instant playback ..........................................................................................
Data-transfer mode............................................................................................................................114 System requirements ............................................................................................................114 Connecting the camera to a computer .................................................................................115 Connecting to Windows 98 / 98 second edition ..................................................................
NAMES OF PARTS CAMERA BODY * This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please read the care and storage instructions in the back of this manual (p. 139). 1. 2. 3. 4. 5. 6. 7. 8. 9. 14 Self-timer lamp (p. 51) Control dial Shutter-release button Exposure-mode dial (p. 39) Flash* (p. 31) White-balance dial (p. 64) White-balance button (p. 64) Strap eyelet (p. 19) Lens release (p. 18) Names of parts 10. 11. 12. 13. 14. 15. 16. 17. 18.
RECORDING MODE DISPLAY VIEWFINDER The recording display shows information on camera operation in panels. The information displayed varies with the functions set. Wide focus frame As the camera is rotated to a vertical position, the display automatically rotates to compensate for the camera position. Spot AF area (p. 47) Local focus areas (p. 57) 1. Exposure mode / exposure panel 2. Flash panel 3. Ev scale 4.
GETTING UP AND RUNNING ATTACHING THE CAMERA STRAP This section covers the preparation of the camera. This includes the changing of batteries, memory cards, and lenses as well as the use of external power supplies. Always keep the camera strap around your neck in the event that you drop the camera. ATTACHING AND REMOVING A LENS This camera uses interchangeable lenses. See page 110 for compatible lenses. Never touch the inside of the camera, especially the lens contacts and mirror.
CHARGING THE BATTERY INSTALLING AND CHANGING THE BATTERY Before the camera can be used, the lithium-ion battery must be charged. Before charging the battery, read the safety warnings on page 4 of this manual. Only recharge the battery with the supplied battery charger. The battery should be recharged before each shooting session. See page 140 for battery care and storage. This digital camera uses one NP-400 lithium-ion battery. Before using the battery, read the safety warnings on pages 4 of this manual.
BATTERY CONDITION INDICATOR TURNING ON THE CAMERA Slide the main switch to the on position to turn on the camera. The access lamp glows briefly to indicate the power is on. When the camera is initially turned on, the date and time should be set, see page 26. When not in use, turn the camera off to conserve power. This camera is equipped with an automatic battery-condition indicator. When the camera is on, the indicator appears on the monitor.
INSERTING AND CHANGING A MEMORY CARD Always turn off the camera and confirm the access lamp is not lit before inserting or removing a memory card, otherwise the card may be damaged, and data lost. A memory card must be inserted for the camera to operate. If a card has not been inserted, “----” is displayed in the frame counter. Type I and II CompactFlash cards and Microdrives are compatible with this camera. 1 2 3 1.
SETTING THE DATE AND TIME BASIC RECORDING After initially inserting a memory card and battery, a message opens requesting that camera’s clock and calendar be set. Images are recorded with the date and time of capture. Depending on the region, the menu language may also have to be set. To change the language, see the setup menu section on pages 98 and 102. SETTING THE CAMERA TO RECORD IMAGES AUTOMATICALLY Turn the exposure dial to the auto or program (P) position. The camera controls are automatic.
1 BASIC RECORDING OPERATION FOCUS SIGNALS Place the subject within the focus frame. The subject must be within the focus range of the lens. If using a zoom lens, change the focal length to frame the subject. The viewfinder focus signal indicates the status of the autofocus system. Focusing time can be longer with macro or telephoto lenses, or in low-light conditions. Press the shutter release button partway down to activate the autofocus and autoexposure systems (1).
FOCUS LOCK 1 USING THE BUILT-IN FLASH The focus-lock function is used when the subject is off-center and outside the focus frame. Focus lock may also be used when a special focusing situation prevents the camera from focusing on the subject. The built-in flash is designed to be used with lenses with focal lengths from 18mm or longer. When using lenses shorter than 18mm, the corners of the image are not be fully illuminated. The lens hood and certain lenses can cause shadowing, see page 110.
ANTI-SHAKE SYSTEM DISPLAY BUTTON The Anti-Shake system minimizes the affect of camera shake, a slight blurring caused by subtle hand motion. Camera shake is more pronounced at long focal lengths than short ones. Press the display button to switch the monitor display among full, basic, and off. For more on the full display, see page 16. Anti-Shake is less effective with moving subjects or when the camera is panned, with shutter speeds of 1/4 second or longer, and short object distances.
HISTOGRAM DISPLAY BASIC PLAYBACK Images can be viewed in the playback mode. This section covers the basic playback functions. The playback mode has additional menu functions, see page 82. VIEWING IMAGES To view the histogram of the displayed image, press the up key. Press the down key to return to single-frame playback. Press the playback button to activate the playback mode. To return to the recording mode, press the playback button or the shutter-release button.
DELETING SINGLE IMAGES CHANGING THE PLAYBACK DISPLAY The displayed image can be deleted. Once deleted, an image cannot be recovered. The display button controls the display format. Each time the button is pressed, the display cycles through to the next format: full display, image only, index playback. The index display can be changed in section 1 of the playback menu. To delete a displayed image, press the delete button; a confirmation screen opens. Use the left/right keys to highlight “Yes.
ENLARGED PLAYBACK An image can be enlarged for closer examination. The maximum magnification depends on image size from 2.4X for small images to 4.7X for large images. ADVANCED RECORDING The front control dial browses through the images. This section contains detailed information on the camera’s recording functions and operation. Read the sections pertaining to your interest and need. EXPOSURE-MODE DIAL The exposure-mode dial is used to select the exposure modes.
Digital subject programs Auto recording Digital subject programs optimize the camera’s exposure, whitebalance, and image-processing systems for specific conditions and subjects. Simply turn the exposure mode dial to select the appropriate subject program. Auto recording is set with the exposure-mode dial. Use this exposure mode when wanting fully-automatic exposure control.
Aperture Priority - A Aperture priority is set with the exposure-mode dial (p. 39). The photographer selects the aperture and the camera sets the appropriate shutter speed to ensure correct exposure. Exposure control range warnings Auto recording, Program, Digital Subject Programs If the required exposure is beyond the shutter speed and aperture range, the shutter speed and aperture displays blink.
Manual Exposure - M Manual exposure mode allows individual selection of shutter speeds and apertures. This mode overrides the exposure system giving the photographer control over the final exposure. Bulb exposures can be made, see below. Manual exposure is set with the exposure-mode dial (p. 39). By pressing and holding the AEL button (1), continuous meter readings are displayed on the Ev scales. Two indices can be displayed. The fixed index shows the meter reading made when the AEL button is pressed.
EXPOSURE LOCK - AEL BUTTON The metered area is 1.0Ev less (–) than the locked exposure. The AE lock button locks the automatic exposure system without activating the AF system. This function allows the exposure to be set by a gray card or reference target outside the scene. When using flash in the auto recording, P, A, or digital subject program exposure modes, slow-shutter sync is active (p. 47). The operation of the AE lock button can be changed in section 1 of the custom menu (p. 94).
EXPOSURE COMPENSATION DEPTH-OF-FIELD PREVIEW When using auto recording, P, A, and S exposure modes or a digital subject program, the exposure can be compensated. To compensate the ambient exposure, press and hold the exposurecompensation button and turn the control dial; the degree of compensation is displayed on the monitor and viewfinder Ev scales. The aperture controls depth of field; the area in front of the camera that appears in focus. The smaller the aperture, the greater the depth of field.
DRIVE MODES Continuous-advance notes The drive modes control the rate and method of image capture. Single-frame advance is the default drive mode and is described in the basic recording section on page 28. The drive mode is set with the drive-mode selection screen. Press the drive-mode button (1) to open the screen. AF Zoom xi and Power Zoom lenses cannot be zoomed when taking pictures with continuous advance. The frame rate is affected by the flash as it must recharge between exposures.
Exposure bracketing notes Bracketing is a method of taking a series of images of a static subject in which each image has a slight variation in exposure. Exposure and flash brackets can be made. Bracketing indicator Bracketing increment in Ev (p. 69) Single-frame advance bracketing When exposure brackets are made in S exposure mode, the aperture controls the bracket.
CAMERA SENSITIVITY (ISO) AND ZONE MATCHING CAMERA SENSITIVITY AND FLASH RANGE Camera sensitivity can be changed. Zone Matching for high-key or low-key subjects can be activated. The sensitivity setting is displayed on the monitor. Press the camerasensitivity button (1) to open the setting screen. Camera sensitivity display Sensitivity / Zone Matching :select :enter Use the four-way keys of the controller to highlight the sensitivity option. The Hi 200 and Lo 80 options are for Zone Matching, see below.
FUNCTION BUTTON AF area AF area, focus mode, metering mode, flash compensation, color mode, and Digital Effects Control are set with the function button. Monitor indicators show active settings. Press the button (1) to open the setting screen. Wide AF area - to use the wide focus frames in the viewfinder to focus. See the basic operation section on page 28. Pressing and holding the four-way controller keys also activates and locks focus with the wide focus area. Spot AF can be used, see page 47.
AF modes Metering modes Single-shot AF (Autofocus), continuous AF, automatic AF, and direct manual focus is set with the function button (p. 56). AF mode Automatic AF :func. :select The AF system activates when the shutter-release button is pressed partway down or with the controller (p. 57). Focus is confirmed with the viewfinder focus signals, see page 29. :enter Automatic AF - this AF mode automatically switches between single-shot AF and continuous AF depending on the subject’s motion.
Flash compensation Color mode The relative output of the flash can be compensated by ±2.0 Ev with the function button (p. 56). Flash compensation ±0.0 Ev :func. :adjust Color / DEC Natural On the function-selection screen, use the up/down keys of the controller to select exposure compensation and the left/right keys to adjust the degree of compensation. Press the central button of the controller to complete the operation. :func.
Digital effects control (DEC) The active mode is displayed on the monitor. When using portrait, landscape, sunset, night view, or night portrait color mode, the use of auto white balance is recommended. Color / DEC Saturation About Adobe RGB Adobe RGB has a larger color gamut than the more common sRGB. The size of the gamut limits the colors that can be reproduced; the larger the gamut, the more colors.
WHITE BALANCE Preset white balance White balance is the camera’s ability to make different types of lighting appear natural. The active white-balance mode is displayed in the white-balance panel on the monitor. With the white balance dial in the preset white balance position, press the white-balance button to open the setting screen. Preset white balance Use the left/right controller keys or control dial to select the white-balance setting. Turn the white-balance dial to the appropriate position.
Custom white balance Custom-white-balance function allows the camera to be calibrated to a specific lighting condition. With the white balance dial in the custom position, press the white-balance button to open the setting screen. A calibration error may occur under extremely bright light sources, especially with flash units. If an error occurs, a message appears on the monitor and the white-balance indicator is yellow.
A SHORT GUIDE TO PHOTOGRAPHY LIGHT SOURCES AND COLOR Photography can be a rewarding pursuit. It is a broad and disciplined field that can take years to master. But the pleasure in making photographs and the joy of capturing a magical moment cannot be compared. The guide is an introduction to some basic photographic principles. The human eye adapts itself extremely well under different conditions. The paper of this manual you are reading looks white regardless of the type of lighting.
RECORDING MENU To set image resolution (p. 72). In recording mode, press the menu button to open and close the menu. The four-way keys of the controller move the cursor in the menu. Pressing the central button of the controller enters a setting. Image size L: 3008x2000 Quality Fine To set file type and compression (p. 72). Inst.Playback 2 sec. To play back images after they are recorded (p. 74). Noise reductn On To apply noise reduction to long exposures (p. 74).
IMAGE SIZE AND IMAGE QUALITY Image size and quality are set in section 1 of the recording menu (p. 70). Changes are displayed on the monitor. L M S RAW RAW+ X.FIN FINE STD. L: 3008 X 2000 (Large) M: 2256 X 1496 (Medium) S: 1504 X 1000 (Small) RAW image RAW & JPEG image Extra fine: JPEG image Fine: JPEG image Standard: JPEG image Image size affects the number of pixels in each image. The greater the image size, the larger the file size.
INSTANT PLAYBACK After an image is captured, it can be displayed on the monitors for two, five, or ten seconds before being saved. The last image of a continuous-advance or continous-advance bracketing series is displayed. Instant playback is activated and the length of the playback period is set with the instant-playback option in section 1 of the recording menu (p. 70). FLASH MODES Image size L: 3008x2000 Quality Fine Inst.Playback 2 sec.
Wireless / remote flash On-camera flash Wireless/Remote flash allows the camera to control an offcamera Program 5600HS (D) and 3600HS (D) flash unit without the need of a cable. Single or multiple flash units can be placed around the subject to create different lighting effects. The camera’s built-in flash fires to control the off-camera flash units rather than to illuminate the subject. Wireless/ Remote flash Flash mode Fill-flash Flash control Red eye Bracket order Rear sync.
Wireless/remote camera and flash ranges FLASH CONTROL ADI and pre-flash TTL flash control are available. Flash control is changed in section 2 of the recording menu (p. 70). The flash control used depends on the lens and flash combination. ADI (Advanced Distance Integration) flash metering - combines distance information from D-series lenses with information from a pre-flash exposure. ADI metering is less influenced by subject reflectance.
BRACKETING ORDER ABOUT DIMAGE MASTER The order in which exposure bracketing frames is captured is selected in section 2 of the recording menu (p. 70). For information on exposure bracketing, see page 52. Flash mode Fill-flash Flash control ADI flash The full version of DiMAGE Master gives you all the tools to organize, examine, and process your images. The Organizer window allows you to sort images quickly into four user-defined classifications.
PLAYBACK MENU To delete images on the memory card (p. 84). In playback mode, press the menu button to open and close the menu. The four-way keys of the controller move the cursor in the menu. Pressing the central button of the controller enters a setting. Delete – Format – View folder Folder name NAVIGATING THE PLAYBACK MENU Lock To format the memory card (p. 85). All folders To select one or all folders to view in playback (p. 85). 100KM028 To select the folder to view in playback (p. 85).
DELETE FORMAT Deleting permanently erases the image. Once deleted, an image cannot be recovered. Care should be taken when using the delete function. Single, multiple, or all images in a folder can be deleted with the playback menu. Before an image is deleted, a confirmation screen appears; choosing “Yes” executes the operation, “No” cancels it. Only the images in the view-folder option in section 1 of the playback menu (p. 85) can be viewed and deleted with the marked frames and all-in-folder options.
LOCK INDEX PLAYBACK FORMAT Single, multiple, or all images on the memory card or in a folder specified with the view-folder option can be locked. A locked image cannot be deleted by either the playback menu functions or the delete button. Important images should be locked. Images are locked in section 1 of the playback menu (p. 82).
SLIDE SHOW Section 2 of the playback menu starts the slide-show function. This function automatically displays images every five seconds on the card or in the folder specified with the view-folder option in section 1 of the menu. DPOF SETUP Slide show Enter DPOF set The DPOF-set option is used to set an order for standard prints from digital images. Single, multiple, or all images on the memory card or in a folder specified with the view-folder option can be printed (p. 85).
DATE IMPRINT To print the date of capture with each image with a compatible DPOF printer, turn the menu option on. To cancel date imprint, simply turn the option off. How the date is printed varies with the printer. Not all printers support this function. OPENING THE CUSTOM & SETUP MENUS Slide show – DPOF set – Date imprint Off Index print – Cancel print – INDEX PRINT To create an index print of all the images in the folder, set the option on.
CUSTOM MENU To set AF or shutter-release priority (p. 93). The custom menu controls operation preferences. See page 91 on how to open the custom menu. Use the left/right keys of the controller to highlight the appropriate menu tab; the menus change as the tabs are highlighted. Priority setup AF FocusHoldButt. Focus hold AEL button AE hold To set the operation of the AEL button (p. 94). Ctrl dial set Shutter speed To specify exposure control with the control dial (p. 95). Exp. comp.
FOCUS-HOLD BUTTON SETUP Some Konica Minolta lenses are equipped with a focus-hold button. The operation of this button can be specified in section 1 of the custom menu (p. 92). This custom function has two options: Focus hold - pressing the focus-hold button on the lens locks the focus. CONTROL-DIAL SETUP Priority setup AF FocusHoldButt. Focus hold AEL button AE hold Ctrl dial set Shutter speed Exp. comp. set Ambient&flash AF illuminator On D.O.F.
AF ILLUMINATOR AF AREA SETUP The built-in flash is used as an AF Illuminator. When the scene is too dark for the camera to focus, raise the built-in flash. It fires a few short bursts to provide light for the camera to focus. When an accessory flash is attached, the flash unit is used as the AF illuminator. The AF illuminator can be turned on and off in section 1 of the custom menu (p. 92). The spot focus or local AF areas are illuminated when the camera focuses.
SETUP MENU To set monitor brightness (p. 100). The setup menu controls camera operation. See page 91 on how to open the setup menu. Use the left/right keys of the controller to highlight the appropriate menu tab; the menus change as the tabs are highlighted. LCDbrightness – Transfer mode Data storage Video output NTSC To switch video output between NTSC and PAL (p. 101). Audio signals On To change or turn off audio signals (p. 102).
LCD BRIGHTNESS Monitor brightness is adjusted in section 1 of the setup menu. Highlight “Enter” and press the central button of the controller to open the LCD brightness setup screen. VIDEO OUTPUT LCDbrightness Camera images can be displayed on a television. The video output can be changed between NTSC and PAL. North America uses the NTSC standard and Europe uses the PAL standard. Check which standard is used in your region to play back images on your television set.
AUDIO SIGNALS When the shutter-release button is pressed partway down, an audio signal gives a positive confirmation the AF system has focused. This signals can be turned off in section 1 of the setup menu (p. 98). DATE AND TIME SETUP LCDbrightness – Transfer mode Data storage Video output NTSC Audio signals On Language Date/Time set It is important to accurately set the clock.
FOLDER NAME NEW FOLDER All recorded images are stored in folders on the memory card. Folder names come in two formats: standard and date. This allows the creation of new folders. The folder-name option in section 2 of the setup menu specifies the folder-name format. If multiple date-format folders are created, only the last folder can be used for storing images. Standard folders have an eight character name. The initial folder is named 100KM028.
MENU SECTION MEMORY The camera can remember which menu section was last opened. If the menu section memory function is on, when the menu button is pressed, the last menu section that was last displayed is opened. When menu section memory is off, section 1 of the recording or playback menu is displayed when the menu button is pressed. LCD backlight 5 sec. Power save 3 min. MenuSec.Memory Off Delete conf.
RESET DEFAULT Playback menu This option resets all camera modes and menus. When selected, a confirmation screen appears; choosing “Yes” resets the following functions and settings, “No” cancels the operation. Recording and Playback mode All folders p. 85 9 frame p. 87 Date imprint Off p. 90 Custom menu Recording display Full display p. 33 AF/Shutter-release priority setup AF priority p. 93 Playback display Single frame p. 37 Focus-hold button setup Focus hold p.
ACCESSORY NOTES ATTACHING THE EYEPIECE CAP This section contains operation and compatibility information with camera accessories. Please read it in its entirety to achieve the best results with your camera. The supplied eyepiece cap prevents light from entering through the viewfinder and affecting the exposure meter or fogging the image when using the self-timer or during long exposures. LENS COMPATIBILITY All Konica Minolta AF lenses are compatible with this camera.
ATTACHING AN ACCESSORY FLASH UNIT PC FLASH ADAPTER PCT-100 To extend the versatility of the camera, an accessory flash unit (sold separately) can be used. Always remove the accessory flash when the camera is not in use, and replace the accessory-shoe cap to protect the contacts. The PC Flash Adapter PCT-100 allows a studio or location flash system to be connected to the camera with a standard PC cord.
DATA-TRANSFER MODE CONNECTING THE CAMERA TO A COMPUTER Read this section carefully before connecting the camera to a computer. This manual does not cover the basic operation of computers or their operating systems; please refer to the manual supplied with your computer. A fully charged battery should be used when the camera is connected to a computer. The AC adapter (sold separately) is recommended over the use of batteries.
CONNECTING TO WINDOWS 98 / 98 SECOND EDITION Manual installation The driver needs only to be installed once. If the driver cannot be installed automatically, it can be installed manually with the operating system’s add-new-hardware wizard; see the instructions on the following page. During installation, if the operating system requests the Windows 98 CD-ROM, inset it into the CD-ROM drive and follow the accompanying instructions on the screen.
AUTO POWER SAVE (DATA-TRANSFER MODE) The add new hardware wizard confirms the location of the driver. One of three drivers may be located: MNLVENUM.inf, USBPDR.inf, or USBSTRG.inf. The letter designating the CD-ROM drive varies between computers. Click “Next” to install the driver in the system. If the camera does not receive a read or write command within ten minutes, it shuts down to save power. When the camera shuts down, an unsafe-removal-of-device warning may appear on the computer monitor. Click “OK.
MEMORY CARD FOLDER ORGANIZATION Once the camera is connected to the computer, image files can be accessed by double clicking on icons. Image folders are located in the DCIM folder. To copy images, simply drag and drop the file icon into a location in the computer. Drive Icon Dcim Misc The misc. folder contains DPOF print files (p. 88). Files and folders on the memory card can be deleted using the computer.
DISCONNECTING THE CAMERA FROM THE COMPUTER Never disconnect the camera when the access lamp is lit - the data or memory card may permanently be damaged. When more than one external device is connected to the computer, repeat the procedure above except right click on the unplug-or-eject-hardware icon to open the unplug-or-ejecthardware window. Windows 98 / 98 second edition Confirm the access lamp is not lit. Turn off the camera and then disconnect the USB cable.
CHANGING THE MEMORY CARD (DATA-TRANSFER MODE) Care should be taken when changing memory cards while the camera is attached to the computer. Data could be lost or damaged if the camera is not properly disconnected. Always confirm the access lamp is out before removing the memory card. REMOVING THE DRIVER SOFTWARE - WINDOWS 1. Insert a memory card in the camera and connect it to the computer with the USB cable. Other devices must not be connected to the computer during this procedure. 2.
PICTBRIDGE Confirm the transfer-mode option in section 1 of the setup menu is set to PTP. Connect the camera to a PictBridge compatible printer using the camera’s USB cable. The larger plug on the cable is connected to the printer. Slide the card-slot door toward the back of the camera to release the safety catch and open. Insert the smaller plug of the cable into the camera. Turn the camera on; the PictBridge screen is displayed automatically.
NAVIGATING THE PICTBRIDGE MENU Pressing the menu button opens and closes the menu. The four-way keys of the controller and the control dials move the cursor in the menu. Pressing the central button of the controller enters a setting. The options that can be changed vary with the printer. Batch print – Paper size Printer setup Index print – Layout Printer setup Print quality Printer setup Data print Printer setup DPOF print – Activate the menu with the menu button.
Paper size Print quality The paper size of the print can be specified in section 2 of the PictBridge menu. The printer-setup option uses the size set with the printer. Paper size Printer setup The print quality can be set in section 2 of the PictBridge menu. The printer-setup option uses the quality set with the printer. The fine quality can be specified with the camera. Layout Data print Print quality Data print Data can be printed with the image in section 2 of the PictBridge menu.
KODAK EASYSHARE SOFTWARE 1. Close all software applications that are open on you computer (including antivirus software). The all-in-one digital photography software solution gives you an effortless way to organize, print, and share your pictures. 2. Place the Digital Camera Software CD-ROM into the CD-ROM drive. Organize your pictures Kodak EasyShare software automatically organizes your pictures so you can find and view them quickly. Or create custom albums and sort pictures your own way.
DIMAGE MASTER LITE DiMAGE Master Lite is your entrance into digital imaging. Image-processing tools Color, contrast, saturation, and sharpness can be optimized to bring out the best in your images. Advanced RAW image processing for specific model DiMAGE cameras ensures highquality results. Image information Detailed information on how and when the image was recorded as well as file specifications can be viewed. Picture editing Download and sort your images quickly and efficiently on your computer.
TROUBLESHOOTING Problem Symptom The section covers minor problems with basic camera operation. For major problems or damage to the camera or charger, or if a problem continues to reoccur frequently, contact a Konica Minolta service facility. Problem Symptom Cause The battery is dead. Nothing displayed on monitor. The camera will not work. The AC adapter is not connected properly. Check that the adapter is connected to the camera and a live electrical outlet (p. 22). Display mode set to off.
Problem Inaccurate exposures with very bright or dark scenes. Symptom Cause Solution Shutter speed and/or aperture display blink. Subject or scene is outside the exposure control range of the camera. Adjust the exposure until the display stops blinking or change camera sensitivity (p. 54). Arrows blink at each end of the Ev scale. Subject or scene is outside the metering range of the camera. In dark conditions, use the camera flash.
OPERATING TEMPERATURES AND CONDITIONS LCD MONITOR CARE • This camera has been designed for use in temperatures from 0°C to 40°C (32°F to 104°F). • Never leave the camera exposed to extreme high temperatures, such as in a car parked in the sun, or to extreme humidity. • When taking the camera from a cold to a warm environment, place it in a sealed plastic bag to prevent condensation from forming. Allow the camera to come to room temperature before removing it from the bag.
The following marks may be found on the product: For EU member states only This mark on your camera certifies that this camera meets the requirements of the EU (European Union) concerning interference causing equipment regulations. CE stands for Conformité Européenne (European Conformity). FCC Compliance Statement Declaration on Conformity This symbol means: Do not dispose of this product together with your household waste.
TECHNICAL SPECIFICATIONS Number of effective pixels: CCD: Camera sensitivity (ISO): Aspect ratio: A/D conversion: Autofocusing system: AF sensitivity range: Meter: Metering range: Shutter: Flash guide number: Flash sync.: Flash coverage: Built-in flash recycling time: Viewfinder: Field of view: Eye relief: Viewfinder magnification: Monitor LCD: Recording media: File formats: PRINT Image Matching III: Menu languages: Video output: 144 Technical specifications 6.1 million APS-C size (23.5 X 15.
INDEX Access lamp, 22, 24, 122, 124 Accessories AC adapter, 22 Flash, 79, 112, 113 Remote cord, 111 Viewfinder, 59 ADI metering, 79 Adobe RGB, 62, 88, 120, 126 AF areas, 17, 56, 57 AE lock button, 46, 94 AF illuminator, 96 AF / MF switch, 49 AF modes, 56, 58 AF / Shutter release priority, 93 Audio signals, 102 Autofocus, 48, 57, 58, Special focusing situations, 29 Spot AF, 47 Auto recording, 27, 41 Anti-Shake, 32, 110 Aperture priority, 42 Auto power save, 23, 105, 119 Battery, Care and storage, 140 Changin
