Service manual

ManualsBrandsMinolta ManualsComputer equipmentDIMAGE SCAN ELITE 5400

Table Of Contents

(2890)A 1

CODE

MINOLTA DiMAGE SCAN Elite 5400 (2890-100)

Scanner Type 35mm film scanner, moving film type

Usable Film Type 35mm film (Color / B&W, negative/positive)

Scanning Dimension 35mm film: 24.61 x 36.69 mm / 5,232 x 7,800pixels

Optical Resolution 5400dpi

Scanning method Fixed sensor, moving film, single-pass scan

Image Sensor 3-line CCD with 5,300 pixels per line, RGB primary color filter

Scan Time (excluding the data transfer time to PC)

- Times listed above do not include data transfer time to the computer.

- Scan time varies with the film images and the scanner preferences and functions used.

- Scan time can be longer for negative film than positive film.

- Approximate time with 5400 dpi (maximum optical resolution), 8-bit color depth,

- No cropping, No auto exposure, No color matching, No Digital ICE processing, No image corrections, No

Grain Dissolver, No Multi-sample scanning

Scan time (Approx.)

Windows Macintosh

Setting

Mode

USB2.0 IEEE1394 FireWire

Index scan 15 sec. 15 sec. 16 sec.

Prescan 10 sec. 10 sec. 12 sec.

Scan 60 sec. 68 sec. 69 sec.

Measuring condition

Windows Macintosh

CPU Pentium 4/ 2.53GHz PowerPC G4

OS Windows XP Professional Mac OS X 10.2.1

RAM 1GB 1GB

Hard-disk space 60.9GB 70.72GB

USB2.0 built-in

Interface

IEEE 1394 Melco IFC-ILP4

FireWire built-in

Application Photoshop 7.0.1 Photoshop 7.0.1

Memory allocated to

application

80% 739MB

Summary of content (34 pages)

PAGE 1
(2890)A 1 MINOLTA DiMAGE SCAN Elite 5400 (2890-100) CODE Scanner Type 35mm film scanner, moving film type Usable Film Type 35mm film (Color / B&W, negative/positive) Scanning Dimension 35mm film: 24.61 x 36.
PAGE 2
CODE 2 (2889)A AD Conversion 16bit (per color channel) Output 8/ 16bit (per color channel) Dynamic Range 3.8 (Tested value) Light Source 3-wavelength cold-cathode fluorescent lamp (Not user-replaceable) Focus Auto focus (Point AF available) Manual focus (driver software/manual focus dial) Others Grain Dissolver, Auto Dust Brush, Digital ICE, Pixel Polish, Quick scan button Interface IEEE1394 (FireWire)(One 6-pin receptacle connector) USB 2.0 (Type-B connector), Compatible with USB1.
PAGE 3
(2890)A 3 System Requirements IBM PC/AT compatible computers OS RAM(*1) Pentium 166MHz or later processor PowerPC G3 or later processor USB: Mac OS 8.6 to 9.2.2, Mac OS X v10.1.3 USB: Windows98, 98 Second Edition, Me, to v10.1.5, and v10.2.1 to 10.2.3 2000 Professional, or XP Professional IEEE1394: Windows Me, 2000 Professional, FireWire: Mac OS 8.6 (*2)to 9.2.2, Mac OS X v10.2.1 to 10.2.
PAGE 4
How to use a Parts List. Product code and product name are shown on each page. You can close them by clicking the "[-]" on the left,if not necessary. Parts list: Clicking [+] of bookmark displays the subordinate headings and clicking the number jumps to each page. Blue for new parts No.by additional parts. Red line for discontinued parts. Illustration: Clicking the parts number "!/!" displays related PML. Right page: * for amendments. PML: Clicking the page number "*/*" displays related illustration page.
PAGE 5
(2890)A 1 INDEX PART NO. PAGE PART NO. PAGE 2 2890-9001 ……………………… 1 2890-0111 ……………………… 1 2890-9002 ……………………… 1 2890-0187 ……………………… 1 2890-9003 ……………………… 2 2890-0401 ……………………… 2 2890-9004 ……………………… 2 2890-0402 ……………………… 2 2890-9005 ……………………… 2 2890-0626 . . . . . . . . . . . 1 2890-0037 . . . . . . . . . . .
PAGE 6
2890-9001-01 (4) PARTS LIST 2890-1002-01 2890-9001-01 (2) 2890-9001-01 (2) 2890-4007-01 2890-1008-01 2890-1004-01 9384-2191-01 (10x30mm) 2890-1007-01 2890-0626-01 2890-4003-01 2890-0187-01 2890-0188-01 See page 2.
PAGE 7
(2890)A 1 PART NO. PART NAME 2890-0111-01 ASSY, FRONT HOUSING QTY. 1 (2890-1009-01) POWER BUTTON 電源ボタン 1 (2890-4002-01) CABEL 6P ケーブル６Ｐ 1 2890-0187-01 USB TERMINAL COVER ＵＳＢターミナルカバー 1 2890-1002-01 UPPER CASE 上ケース 1 2890-1004-01 PLATE SAFETY 定格ラベル 1 2890-1005-01 SERIAL NUMBER LABEL ボディＮＯ．ラベル 1 2890-1006-01 FOCUS DIAL フォーカスダイアル 1 2890-1007-01 ARM アーム 1 2890-1008-01 POWER SW.
PAGE 8
2890-4004-01 2890-0401-01 2890-9003-01 (2) PARTS LIST (2890-4101-01) 2890-4005-01 9384-2792-00 (8x20mm) 2890-0110-01 2890-9003-01 (2) (2890-4006-01) (9384-2191-00) (10x10mm) (9384-2191-00) (10x20mm) (2890-1102-01) (2890-9007-01) (2) Not available as a single part. 単品非供給 (2890-4201-01) (2890-9102-01) (2) (2890-4001-01) 2890-0091-01 2890-0065-01 (2890-9101-01) (2) (2890-9006-01) (4) 2890-1003-01 2890-9005-01 5.5mm 2890-9005-01 (2) 8mm 2890-0402-01 M3 2890-9003-01 2890-9006-01 3.
PAGE 9
(2890)A 2 PART NO. PART NAME 2890-0110-01 ASSY, SCAN UNIT QTY.
PAGE 10
(2890)A 1 REF No. 管理No. PARTS MODIFICATION LIST QS FA 2890-P001 DPCS Division Division DPCS部主管部署 Valid from March 17. 2003 施行年月日 Parts List P. 2 Approved by Verified by Written by 承認審査作成 Tanizaki Naruto Ueno Tozuka 仮-891 REASON サービス供給として設定する変更理由 To supply as a spare part 2890-0110-01 Previous Previous ―――――― COMMON MODEL 共通機種 ―― ―― 2890-100 2890-0110-01 (2890-4201-01) ―― ―― New New (2890-4201-01) MOTOR モーター A d d e d . / 新規手配 REF No. 管理No.
PAGE 11
(2890)A 2 REF No. 管理No. PARTS MODIFICATION LIST QS FA 2890-P003 CS Division Division CS部主管部署 Valid from April 27. 2004 施行年月日 Parts List P. 1 Approved by Verified by Written by 作成 Tanizaki Naruto Ueno 仮-897 ―― ―――――― 審査 COMMON MODEL 共通機種 REASON サービス供給として設定する変更理由 To supply as a spare part Previous 承認 ―― 2890-100 2890-0187-01 New 2890-0187-01 USB TERMINAL COVER U S B ターミナルカバー To suuply as a spare part. サービス供給として設定 REF No. 管理No.
PAGE 12
(2890)A 3 REF No. 管理No. PARTS MODIFICATION LIST QS FA 2890-P005 Camera CS Division Division カメラCS部主管部署 Valid from October 15. 2004 施行年月日 Parts List P. 1 Approved by Verified by Written by 作成 Tanizaki Naruto Ueno 仮-911 ―― ―――――― 審査 COMMON MODEL 共通機種 REASON サービス供給として設定する変更理由 To supply as a spare part Previous 承認 ―― 2890-100 2890-0626-01 New 2890-0626-01 S C R E W / ねじ A d d . / 新説 REF No. 管理No. QS FA 2890-P006 Camera CS Division Division カメラCS部主管部署 Valid from October 15.
PAGE 13
(2890)A 4 REF No. 管理No. PARTS MODIFICATION LIST QS FA 2890-P007 Camera CS Division Division カメラCS部主管部署 Valid from October 15. 2004 施行年月日 Parts List P. 1 Approved by Verified by Written by ―――――― 審査作成 Tanizaki Naruto Ueno 仮-911 COMMON MODEL 共通機種 REASON サービス供給として設定する変更理由 To supply as a spare part Previous 承認 ―― ―― 2890-100 2890-0188-01 PML 2890-0188-01 IEEE CAP I E E E キャップ A d d .
PAGE 14
(2890) REF No. 管理No. 5 PARTS MODIFICATION LIST QS FA 2890-P008 Camera CS Division Division カメラCS部主管部署 Valid from July 15. 2005 施行年月日 Parts List P.
PAGE 15
(2890) A 1 REPAIR GUIDE Contents of this manual are in accordance with the assembly procedure. Therefore, follow the reverse procedure when disassembling. SYMBOLS : Caution and key points of assembly : Anti-diffusion agent : Adhesive : Grease : Tools TABLE OF CONTENTS Page PRECAUTIONS Chemicals Handle chemicals of high volatility with care, use of which will affect to your health and environment. 1. Store them sealed in a specific place to prevent from exposure to high temperature or direct sunlight. 2.
PAGE 16
2 Assy, Scan unit, Main PCB Assy Installation Fig. 4 Cable 4P Main PCB Assy 9003 (2) B-10 Fig. 3 B-51 REPAIR GUIDE Cable 30P 9384-2792-00 (8x20mm) Fig. 2 Assy, Scan unit 9003(2) FFC Cable 8P 9384-2191-00 (10x10mm) 9384-2191-00 (10x20mm) Fig. 2 Reflection plate 9007 (2) Not available as a single part. Fig. 1 Nut (2) Fluorecsent light Washer (2) 9006(4) Lower case 2890-9005-01 5.5mm 9005 (2) 8mm IF 16 PCB assy M3 2890-9003-01 2890-9006-01 3.
PAGE 17
3 Focus dial, Arm, Assy, Front housing Installation 9001 (4) Upper case REPAIR GUIDE 9001 (2) 9001(2) Coil Power SW SP Fig. 5 Fig. 6 Plate safety 9384-2191-01 (10x30mm) Arm Fig. 8 FFC cable 18P Fig. 2 9384-2792-00 (18x18mm) 9384-2191-00 (4) (10x20mm) Fig. 2 9002 (2) Power button Fig. 9 Gear 12T Rubber holder-B Rubber stand (2) Serial number label 9001 (2) Rubber holder-A Cable 6P Assy, Front housing Rubber stand (2) 9002 (2) 9001 (2) Fig. 9 Focus dial 2890-9001-01 5mm 2890-9002-01 7.
PAGE 18
4 (2890) A REPAIR GUIDE " Fig. 1 Fluorescent Lamp Replacement Procedure. Disassembly 1. Remove 4 fluorescent lamp holder (not supplied) fixing screws (9006) (in the circle). Never loosening fluorescent lamp holder fixing screws except the screws marked in the figure (in the circle). Assembly 1. Install nut (9102) to the fluorescent lamp holder (not supplied) and fluorescent lamp (4001) in a groove of the nut. 2. Remove 2 fluorescent lamp fixing screws (9007).
PAGE 19
(2890) A 5 " Fig. 2 FFC cable 18P 20mm Bend at this line. FFC cable 8P Bend at this line 9384-2191-00(10x10mm) 35mm 9384-2191-00(10x20mm) Put through downside. Put through a hole of Main PCB. REPAIR GUIDE FFC cable 18P FFC cable 18P 9384-2191-00(10x20mm)(3) Attach FFC cable 18P to Image taking unit. FFC cable 8P 9384-2191-00(10x20mm) Attach FFC cable 8P to Image taking unit. FFC cable 8P FFC cable 18P 9384-2792-00(18x18mm) 9384-2792-00(8x20mm) " Fig.
PAGE 20
6 (2890) B " Fig. 4 " Fig. 5 Connect the connector by the position as shown. The red / brown solenoid Red / black inverter PCB Coil installation. Coil Main PCB REPAIR GUIDE Red / orange Power SW Bottom cover " Fig. 6 Arm installation. Install the arm notch aligning with the Image taking unit. (in the circle) 9384-2191-01(10x30mm) Install a coil into the bottom cover. After installing the coil on the lower case with 9384-2191-01, apply B-51 into the shaded area to prevent the coil from detaching.
PAGE 21
(2890) A 7 " Fig. 9 Focus dial Assembly Procedure. DiMAGE Scan Utility is necessary for this procedure. Please install "DiMAGE Scan" Software from CD-ROM to your PC. Preparations 1. Remove top cover, front cover assy, focus dial and gear 12T. 2. Keep the front cover assy connected to the Image taking unit with cable 6P. (Fig. 9-1) 3. Connect scanner (2890) and PC via USB (or, IEEE1394) cable. 4. Power on the scanner. 5. Start "DiMAGE Scan Utility", and be standby for scanning.
PAGE 22
8 (2890) A Measuring Instruments, Tools and Jigs REPAIR GUIDE Slide Mount Holder (SH-M10) DiMAGE Scan Ver. 1.1.0 (CD-ROM) AC Adapter PC/AT compatibles CPU: Pentium III or later RAM: 500MB or more HDD: Approx. 2GB or more of available hard-disk space OS: Windows 98, 98SE, Me, 2000 Professional Monitor: 1024 x 768 (pixels) is recommended.
PAGE 23
(2890) A 1 CHECK LIST 1. This Check List describes the quality of operation warranted to general users. When users inquire about quality or request inspection, refer to this Check List. Use this list also when checking operation after repair. 2. When using this list at shipping or receiving inspection, judge the quality according to the purpose of the inspection, not by directly referring to this level. 3.
PAGE 24
2 (2890) A Check the scanner with the computer which meets the system requirements in the last page of this check list. The driver software DiMAGE Scan supplied with the product is necessary for check. If this driver is not installed in the computer, please install it beforehand. NAMES OF PARTS 1. Front Door 2. Indicator Lamp Glows steadily: Scanner is ready to use. Off: Power off Blinks slowly: Scanning, Loading, or initializing. Blinks rapidly: Error 3. Power Switch 4. Front Door reset hole 5.
PAGE 25
(2890) A 3 FUNCTION Power Switch ON Before starting the driver, the indicator blinks. At using the driver software, the indicator lamp glows or blinks accordingly as below. OFF Lamp Condition Glowing Normal except for the following. Blinking slowly at 1Hz Mechanical drive (setup) Blinking fast at 8Hz Error The indicator lamp turns off. PC Interface USB 2.0 / 1.1 or IEEE1394 Eject button When the scanner is not operating (stand-by), pressing the Eject button ejects the holder immediately.
PAGE 26
4 (2890) A PERFORMANCE Outline Basically, 2890 performance will be checked accordingly as below. Scan: Scan the chart and save the image with the driver software. Measure: Take in the image and measure the data with the Adjustment program. Check: Output the data in the excel sheet and check the performance.
PAGE 27
(2890) A 5 Setting the chart Make sure the chart faces the CCD side in the Slide Mount Holder (SH-M10) as illustrated. Up: Fluorescent Front view Side view Down: CCD 1) Click Start > Programs > Minolta DiMAGE Scan Ver. 1.1 > DiMAGE Scan Utility. 2) Set the preferences as below.
PAGE 28
6 (2890) A 3) Select the blank area (A) and click the Prescan button and confirm if each RGB value is 200 "30. A RGB value should be 200!30 B Manual focus Point 4) Click on the Manual focus button and move the mouse pointer to the manual focus point (B), then drag the focus meter slider until the black and white lines are at their longest. CAUTION: Drag the slider from the left to the right. 5) Confirm that the image is selected entirely, and click the Scan button to start the final scan.
PAGE 29
(2890) A 7 3) Click File > File Open and select the image file saved in 1.3.7). The result will be copied in a clipboard on PC. CAUTION: Paste the result data on an excel sheet in the next step before using other applications. Otherwise the result will be lost. Check 1) Open 2890data sheet.xls in the FD and select the worksheet “Scanner Gauge”. 2) Move the mouse pointer to the cell F3, and click Edit > Paste. The file name is inputted in F3 and the performance data is inputted in the column F.
PAGE 30
8 (2890) A Color Chart Preparation 2890Adjustment Program FD Version 1.0 2887Adjustment Program CD Version 1.0 DiMAGE Scan Ver. 1.1.0 (CD) Color Chart Slide (35mm) Slide Mount Holder (SH-M10) Microsoft Excel Setup 1. Confirm the driver software DiMAGE Scan Ver. 1.1.0 is launched or not. If not installed yet, please install the driver software first. Be sure to remove the DiMAGEScan.ini from the folder after scanning the chart.
PAGE 31
(2890) A 9 Scan 1) Click Start > Programs > Minolta DiMAGE Scan Ver. 1.1 > DiMAGE Scan Utility. 2) Set the preferences as below. Scanning condition Film format 35mm Film Type Color Positive Input resolution 540 dpi 3) Click on the Prescan button to prescan the chart. Check that the chart is scanned as shown and that it is not underexposure. 4) Click on the Point AF button and move the mouse pointer to the center of the image and then start the Auto Focus. 6) Save the image as .BMP file.
PAGE 32
10 (2890) A 3) Click “New” of the Profile and input a profile name, and then click on the Save button. The setting will be effective from the next measurement. 4) Click File > File Open and select the image file saved in Scan step 6). 5) Click the direction buttons (A) until the measuring points are at the center of each color, and click OK button. A CHECK LIST 6) The result will be copied in a clipboard on PC.
PAGE 33
(2890) A 11 Standard Scanner gauge chart Magnification Vertical Horizontal Aspect ratio +/± 1.5% ± 1.5% ± 1.0% Vertical Horizontal Aspect ratio +/± 0.5% ± 0.5% ± 0.5% Skew Color Registration Vertical Horizontal +/± 1.5 pixel ± 1.5 pixel Vertical Horizontal +/± 1.0 % ± 1.
PAGE 34
12 (2890) A Color Balance Chart Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 White Gray2 Gray3 Gray4 Gray5 Black Chart B G R Y M C a* 23"10 -44"10 48"10 -5"10 50"10 -18"10 +/10 or less 10 or less 10 or less 10 or less 10 or less 16 or less Color Reproduction b* -53 ± 10 13 ± 10 46 ± 10 51 ± 10 -19 ± 10 -32 ± 10 Equipment Required CHECK LIST PC/AT compatibles CPU Pentium III or later RAM 500MB or more HDD Approx.