Data Management Software CL-S10w Installation Guide
Safety Warning Please read this manual and the instrument and computer manual carefully beforehand and use the software properly and safely.
• • • Please do not apply force or drop the CD-ROM. Please do not apply water, alcohol or thinner etc to the CD-ROM. Please remove the CD-ROM only when the PC is switched on. Note about the storage • • • Please store the CD-ROM in its case after use and take good care of it. Please do not store in direct sunlight or near areas with high temperatures such as heaters. Please do not store the CD-ROM in areas of high humidity.
Contents Installation procedures..............................................................................................................4 When using Windows XP, Excel 2003 1. 2. 3. When using Windows 7, Excel 2007 1. 2. 3. When using Windows 8, Excel 2013 1. 2. 3. About the template 1. 2. 3. 4. 5. 6. 7. Installation.......................................................5 Installation of the device driver.......................8 Uninstallation of CL-S10w .........................
Windows XP, Excel 2003 When using Windows XP, Excel 2003 1. Installation 1 2 3 Start Windows. Set the CL-S10w CD-ROM in the CD-ROM drive. The installation program should start up automatically. Please double-click on the Setup.exe icon if the installation does not start automatically. Select a language from the language dialog box and click OK . ‘Chinese’ is in simplified form. When using Traditional Chinese OS, please select the ‘English’. We shall proceed and explain with the ‘English’ hence on.
Windows XP, Excel 2003 6 Check the destination folder to install to and click Next . The destination folder can be changed. Please remember the path of the destination folder as it is necessary during the Excel Add-Ins setup. 7 Click Install . 8 Click Finish when the installation is completed. 9 6 File copy will begin. Next add CL-S10w into Excel Add-Ins. Start Excel 2003 and choose ‘Add-Ins’ from ‘Tools’ in the menu bar.
Windows XP, Excel 2003 10 11 Click Browse from the Add-Ins setting menu. Select the destination folder where CL-S10w is installed and select the CL-S10w.xla (the file extension might not be shown in some cases) and click OK . (Example) C: \Program Files \KONICAMINOLTA\CL-S10w 12 13 Check the ‘Cl-S10w’ added in the Add-Ins setting menu and click OK . “CL-S10W” was added to the menu bar in Excel 2003.
Windows XP, Excel 2003 2. Installation of the device driver Connecting the instrument to a USB port of the PC requires the device driver to be installed. Please follow the steps below. For CL-500A 1 Connect the instrument to a USB port of the PC. Device driver installation will begin. 2 Wait for a while until the following message appears. Two kinds of device drivers for CL-500A will be installed. The installation may take several minutes.
Windows XP, Excel 2003 For CL-200A 1 With the CL-S10w installation CDROM inserted in the PC, connect the instrument to a USB port of the PC. Select ‘No, not this time’ and click Next , when the Found New Hardware Wizard pops up. 2 3 Select ‘Install from a list or specific location (Advanced)’ and click Next . Select ‘Search for the best driver in these locations’ and check the ‘Search removable media (floppy, CD-ROM...)’ and click Next .
Windows XP, Excel 2003 4 5 Click Finish . Select ‘No, not this time’ and click Next , when the Found New Hardware Wizard pops up. After clicking Next , when the screen from Step 2 appears again, select ‘Install from a list or specific location (Advanced)’ and click Next . 6 Select ‘Search for the best driver in these locations’ and check the ‘Search removable media (floppy, CD-ROM...)’ and click Next .
Windows XP, Excel 2003 8 Check the COM port assigned to the photometer. Select ‘Control Panel’ from the Start menu, select ‘System’, then select ‘Device Manager’ from the ‘Hardware’ tab and expand the ‘Ports (COM & LPT)’ to show the assigned COM port number. Note This COM port number is necessary to start CL-S10w and to connect the photometer. The above installation is completed. 3. Uninstallation of CL-S10w (Before version up) 1 Firstly uncheck the ‘Cl-S10w’ from the Excel Add-Ins setting menu.
Windows 7, Excel 2007 When using Windows 7, Excel 2007 The screens might differ from those in Excel 2010, but the steps are the same. Please follow the steps below. You will see a User Account Control dialog box during installation of the software. At that time, select "Yes" or "Continue". 1. Installation 1 2 3 Start Windows. Set and insert the CL-S10w CD-ROM in the CD-ROM drive. The installation program should start up automatically. Please double-click on the ‘Setup.
Windows 7, Excel 2007 6 Check the destination folder to install to and click Next . The destination folder can be changed. Please remember the path of the destination folder as it is necessary during the Excel Add-Ins setup. 7 Click Install . 8 Click Finish when the installation is completed. File copy will begin.
Windows 7, Excel 2007 9 10 11 14 Next add CL-S10w into Excel Add-Ins. Start Excel 2007, click on the top left round icon and click Excel Options from the menu. Select ‘Add-Ins’ on the left and click Go in the Manage Add-Ins below. Click Browse from the Add-Ins setting menu.
Windows 7, Excel 2007 12 Select the destination folder when CL-S10w is installed and select the CL-S10w. xla (the file extension might not be shown in some cases) and click OK . (Example) C: \Program Files \KONICAMINOLTA\CL-S10w 13 14 Check the ‘Cl-S10W’ added in the Add-Ins setting menu and click OK . “CL-S10W” was added to the “Add-Ins” in the menu bar in Excel 2007.
Windows 7, Excel 2007 2. Installation of the device driver Connecting the instrument to a USB port of the PC requires the device driver to be installed. Please follow the steps below. For CL-500A 1 Connect the instrument to a USB port of the PC. The installation of the device driver should start automatically, and select the icon showing Installing device driver software from the taskbar. 2 Click on ‘Skip obtaining driver 3 Click Yes in the Confirmation window.
Windows 7, Excel 2007 5 Use the following procedure to heck that the device drivers are properly installed. Right click on the ‘Computer’ from the Start menu and select ‘Properties’. The screen below will appear after clicking ‘Device Manager’ on the left of the Control Panel. On this screen, make sure that “USB Composite Device” has properly been installed.
Windows 7, Excel 2007 For CL-200A 1 With the CL-S10w installation CDROM inserted in the PC, connect the instrument to a USB port of the PC. The installation of the device driver should start automatically, and select the icon showing Installing device driver software from the taskbar. 2 Click on ‘Skip obtaining driver software from Windows Update’. 3 Click Yes in the Confirmation window. 4 Wait for the screen below to appear and click Close . Please wait for a while as this may take several minutes.
Windows 7, Excel 2007 5 Right click on the ‘Computer’ from the Start menu and select ‘Properties’. Clicking on ‘Device Manager’ on the left of the Control Panel will open the screen as shown to the right. 6 Right click on ‘FT232R USB UART’ and select ‘Update Driver Software’. 7 Click on ‘Browse my computer for driver software’.
Windows 7, Excel 2007 8 Designate the driver folder in the CL-S10w CD-ROM and click Next . (Example) In the case of CD-ROM in E drive. E:\driver 9 10 Click Close . Select the icon from the taskbar like Step 1 as the USB Serial Port device driver will start installation automatically. Click on ‘Skip obtaining driver software from Windows Update’ and click Yes in the Confirmation window. 11 20 Wait for the screen below to appear and click Close .
Windows 7, Excel 2007 12 Show the Device Manager like Step 5 and right click on the ‘USB Serial Port’ and select ‘Update Driver Software’. 13 Click on ‘Browse my computer for driver software’. 14 Designate the driver folder in the CL-S10w CD-ROM and click Next . (Example) In the case of CD-ROM in E drive. E:\driver 15 Click Close .
Windows 7, Excel 2007 16 Check the COM port assigned to the photometer. Show the Device Manager like Step 5 and expand the ‘Ports (COM & LPT)’ to show the assigned COM port number. Note This COM port number is necessary to start CL-S10w and to connect the photometer. The above installation is completed. 3. Uninstallation of CL-S10w (Before version up) 1 Firstly uncheck the ‘Cl-S10W’ from the Excel Add-Ins setting menu. Please follow steps 9-10 to show the AddIns setting menu.
Windows 8, Excel 2013 When using Windows 8, Excel 2013 Be sure to use a 32-bit Excel even if the OS is a 64-bit version. The setup procedure for Excel 2010 is the same as that for Excel 2013, though the screen layout may differ between these Excel versions. Please follow the steps below. You will see a User Account Control dialog box during installation of the software. At that time, select "Yes" or "Continue". 1. Installation 1 2 Start Windows. Set and insert the CL-S10w CDROM in the CD-ROM drive.
Windows 8, Excel 2013 5 6 Read the License Agreement and select ‘I accept the terms in the license agreement’ if you agree to it and click Next . Check the destination folder to install to and click Next . The destination folder can be changed. Please remember the path of the destination folder as it is necessary during the Excel Add-Ins setup. 7 24 Click Install . File copy will begin.
Windows 8, Excel 2013 8 9 10 Click Finish when the installation is completed. Adding CL-S10w into Excel Add-Ins: Start Excel 2013 and click on Options on the left menu. Select ‘Add-Ins’ on the left and click Go in the Manage Add-Ins below.
Windows 8, Excel 2013 11 12 Click Browse from the Add-Ins setting menu. Select the destination folder when CL-S10w is installed and select the CL-S10w. xla (the file extension might not be shown in some cases) and click OK . (Example) C: \Program Files \KONICAMINOLTA\CL-S10w 13 14 Check the ‘Cl-S10W’ added in the Add-Ins setting menu and click OK . “CL-S10W” was added to the “Add-Ins” in the menu bar in Excel 2013.
Windows 8, Excel 2013 2. Installation of the device driver Connecting the instrument to a USB port of the PC requires the device driver to be installed. Please follow the steps below. For CL-500A 1 Connect the instrument to a USB port of the PC. Device driver installation will begin. Two kinds of device drivers for CL-500A will be installed. The installation may take several minutes. Do not turn off the power of CL-500A or pull out the USB cable until the installation is complete.
Windows 8, Excel 2013 For CL-200A 1 With the CL-S10w installation CDROM inserted in the PC, connect the instrument to a USB port of the PC. Device driver installation will begin, and the task bar will show an icon named "Installing device driver software". 2 Place the cursor at the lower left corner of the screen. When a window opens, right-click. Clicking on ‘Device Manager’ will open the screen as shown to the right. 3 Right click on ‘FT232R USB UART’ and select ‘Update Driver Software’.
Windows 8, Excel 2013 5 Designate the driver folder in the CL-S10w CD-ROM and click Next . (Example) In the case of CD-ROM in E drive. E:\driver 6 7 Click Close . Then, install the USB serial port device driver in the same manner as steps 2 to 6.
Windows 8, Excel 2013 8 Check the COM port assigned to the photometer. Show the Device Manager like Step 2 and expand the ‘Ports (COM & LPT)’ to show the assigned COM port number. Note This COM port number is necessary to start CL-S10w and to connect the photometer. The above installation is completed. 3. Uninstallation of CL-S10w (Before version up) 1 Firstly uncheck the ‘Cl-S10W’ from the Excel Add-Ins setting menu. Please follow steps 9-10 to show the AddIns setting menu.
About the template Excel templates are installed together with CL-S10w. The measurements in CL-S10w can be done immediately in these templates. Please use them for references when creating various templates for various use. The templates are placed in the Template folder where CL-S10w is installed. (Example) C:\Program Files\KONICAMINOLTA\CL-S10w\Template In addition, select Start Menu -> All programs -> KONICAMINOLTA -> CL-S10w -> Template to start the template.
2. A u'v' chroma diagram plot The measured data are shown in a graph form in a u'v' chroma diagram. The u'v' chroma diagram is an improved chroma diagram that compares the distance between the chroma points in the xy chroma diagram and the difference in the subjective color difference. 3. Rank display The rank is displayed in several separated regions of the xy chroma range. With regards to the chroma of LED etc, whether there is a match among the various standards can be determined easily.
4. Color Rendering Index Color rendering indexes are shown visually for easy understanding. 5. Spectral Spectral irradiance data are displayed as the spectral waveform.
6. Multi-point measurement CL-200/CL200A allows multi-point measurement using multiple heads.
7. MacAdam ellipse and SDCM This template shows the chromaticity variation of light sources as a MacAdam ellipse and SDCM (Standard Deviation of Color Matching).
2 9222-1826-18 © 2012-2013 KONICA MINOLTA, INC.
