Mesa Model No.
Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.
Congratulations on your purchase of a Minka-Aire ceiling fan! Your new fan will be a beautiful addition to your home, and will keep you comfortable throughout the year. Minka-AireTM offers a variety of ceiling fans: combinations of wood and brass finishes, solid designer colors, and unique glass and crystal designs. A large selection of light fixtures and light kits are also available. Ask your dealer about accessories that will allow you to customize your fan.
SAFETY RULES 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams. 3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring. 4.
INSTALLING THE FAN Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. PARALLEL WOOD BRACE (Min. 2" Thick) CEILING JOIST CROSS BRACE OUTLET BOX OUTLET BOX CEILING JOIST OR CROSS BRACE CEILING JOIST FIG. 1 FIG. 2 HANGER BAR (OPTIONAL) CEILING JOIST OUTLET BOX MOUNTING BRACKET FIG. 3 MOUNTING OPTIONS If there isn't an existing mounting box, Figure 1, 2 and 3 are examples of then read the following instructions.
FLUSH MOUNT CEILING FAN INSTALLATION 1. DISCONNECT ELECTRICITY to the existing fixture occupying the space where you would like to install the fan. After removing the old fixture, check the mounting and stability of the ceiling outlet box. If the outlet box is secure, then precede with the installation procedure. If not, reinforce the outlet box for strength and safety, and then proceed. 2.
INSERT "A" WIRING DIAGRAMS FAN CONTROLLED BY PULL CHAIN, LIGHT KIT CONTROLLED BY PULL CHAIN. HOUSE WIRE SUPPLY WHITE (NEUTRAL) BLACK (HOT) GREEN (GROUND) CEILING WALL WHITE (NEUTRAL) BLUE (OPTIONAL LIGHT) GROUND (CONNECT T O BLACK (MOTOR) GROUND WIRE ON HANGER BRACKET IF NO HOUSE GROUND WIRE EXISTS.) Fan FAN CONTROLLED BY PULL CHAIN, LIGHT KIT CONTROLLED BY WALL SWITCH.
FLUSH MOUNT FAN BLADE INSTALLATION Each set of blade holder has gone throuhh stringent factory testing and is weighed and matched to within one gram. In addition to size and weigh, grain color, and texture, and lacquer consistency have aslo been checked to insure long life in both performance and beauty. A 1 1. LAYOUT THE BLADES AND BLADE IRONS, and locate the proper screws for attaching thr blades to the blade irons. 2.
ATTACHING THE SWITCH CUP Step 1. Remove the screws from the switch cup plate. While holding the switch cup, firmly snap the wire molexes together. Next, slide switch cup up against plate and rotate it until the screw holes are aligned. Secure switch cup to plate using the screws removed earlier. (Fig. 1) SWITCH CUP PLATE WIRE CONNECTOR PLUG SCREWS 1 NOTE: DO NOT PINCH WIRES BETWEEN THE SWITCH HOUSING AND THE SWITCH CUP PLATE. Step 2. Attach the pull chain fob to the chain on the switch cup. (Fig.
OPERATING YOUR FAN Restore power to ceiling fan and test for proper operation. Speed settings for warm or cool weather depend on factors such as the room size. Ceiling height, number of fans, etc. The Reverse switch is located on the switch cup. Slide the switch to the Left for warm weather operation. Slide the switch to the Right for cool weather operation. NOTE: Wait for fan to stop before changing the setting of the slide switch.
CARE OF YOUR FAN Here are some suggestions to help 3. If your fan is provided with wood veneer blades; you can apply a light coat of maintain your fan. furniture polish for additional protection 1. Because of the fan's natural movement and enhanced beauty. Cover small scratches some connections may become loose. with a light application of shoe polish. Check the support connections, brackets and blade attachments twice a year. Make 4. Use a lint free lightly damp cloth or sure they are secure.
TROUBLESHOOTING Symptoms Solution Fan Will not Start Check to make sure the wall switch is turned on. Check circuit fuses or breakers. Caution! Make sure the power is turned off before performing the following steps; Remove canopy and check wire connections. If using a remote controlled fan; check to see that the deep switches from transmitter and receiver are set to the same frequency code. Check wall control transmitter connections (if applicable).
