TIMELESS BY INSTRUCTION MANUAL WARRANTY CERTIFICATE
Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.
The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer. This warranty is only valid to the original purchaser or user against all defects in material and workmanship (light bulbs excluded) for one (1) full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minka Aire ceiling fan (excluding wall controls and electrical components), to the original purchaser or user.
Warranty Service Information To obtain warranty service during the warranty period, the purchaser should return the fan with the sales receipt to the original place of purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty claim. Replacement is subject to availability of the same model. If the model is unavailable it will be replaced by one of equal value.
SAFETY RULES.....................................................................................1 ATTACHING THE FAN BLADES.......................................................... 7 PACKAGE CONTENTS..................................................................... 2 ATTACHING THE SWITCH CUP......................................................... 8 INSTALLING THE FAN.....................................................................3 OPERATING YOUR FAN............................................
1 SAFETY RULES 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams. 3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring. 4.
NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be supplied by the person (s) installing, caring for and operating the unit. NOTE: READ AND SAVE ALL INSTRUCTIONS! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L.
2 PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Fan blades (5) 2. Hanger bracket, canopy and canopy cover assembly 3a. Standard downrod assembly 3b. Minimum-length downrod (for close to ceiling mounting only) 4. Coupling cover 5. Fan motor/housing assembly 6. Blade holders (5) 7. Switch cup plate 8. Switch cup 9. Balancing kit A. Mounting hardware: #10 x 1.5" Wood screws (2 PCs.) #8 x 3/4" Machine screws (2 PCs.) Lock washers (2 PCs.
Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. MOUNTING OPTIONS INSTALLING THE FAN OUTLET BOX CROSS BRACE If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials.
4 HANGING THE FAN WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the proper installation of your new ceiling fan. The use of other parts, hardware or components not supplied by Minka Aire® with the fan will void the Minka Aire® Warranty. REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise.
Step 7. Slip Coupling Cover and Canopy onto Downrod. Carefully re-install the Hanger Ball onto the Downrod being sure that it's properly positioned over the Cross Pin and the wires are not twisted, tighten Set Screw. (Fig. 10) HANGER BRACKET Step 8. Lift the Motor Assembly and place the Hanger Ball into the Hanger Bracket. Rotate the Motor Assembly as needed until the check groove from the Hanger Ball rests firmly over the registration tab from the Hanger Bracket.
DOWNROD OUTLET BOX CROSS PIN DOWNROD SET SCREWS HITCH PIN LOCK PIN HANGER BALL SET SCREW COUPLING *OMIT COUPLING COVER WHEN THE MINIMUM-LENGTH DOWNROD SUPPLY WIRES CANOPY CANOPY COVER SET SCREWS REGISTRATION SLOT DOWNROD HANGER BRACKET Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 11 HITCH PIN Fig.
ELECTRICAL CONNECTIONS REMEMBER to shut the power off at the circuit breaker or fuse box. Follow the steps below to connect the fan to your house supply wires. Use the wire nuts supplied with your fan. Secure the wire nuts by wrapping the connection with electrical tape. FAN CONTROLLED BY PULL CHAIN, LIGHT KIT CONTROLLED BY PULL CHAIN. HOUSE WIRE SUPPLY WHITE (NEUTRAL) BLACK (HOT) Step 1. Connect the black (hot) wire from the ceiling to the black and the blue wires from the fan.
FAN CONTROLLED BY PULL CHAIN, LIGHT KIT CONTROLLED BY WALL SWITCH. FAN CONTROLLED BY WALL CONTROL, LIGHT KIT CONTROLLED BY LIGHT SWITCH. HOUSE WIRE SUPPLY WHITE (NEUTRAL) GREEN (GROUND) BLACK (HOT) HOUSE WIRE SUPPLY WHITE (NEUTRAL) GREEN (GROUND) BLACK (HOT) CEILING CEILING LIGHT SWITCH LIGHT SWITCH WALL BLUE (OPTIONAL LIGHT) BLACK (MOTOR) WIRING OPTION 1 WHITE (NEUTRAL) FAN WALL CONTROL GROUND (CONNECT TO GROUND WIRE ON HANGER BRACKET IF NO HOUSE GROUND WIRE EXISTS.
6 FINISHING THE INSTALLATION OUTLET BOX Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half a turn from the screw head. HANGER BRACKET Step 2. Slide the canopy up towards the hanger bracket and place the key hole on the canopy over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 15) CANOPY Step 3.
7 ATTACHING THE FAN BLADES Step 1. Attach the fan blades to the blade holders using the screws and fiber washers provided, tighten screws securely. (Fig. 16) FAN BLADE SCREWS FAN MOTOR FIBER WASHERS Step 2. Remove rubber stops from motor. Rotate motor so that the screw holes are revealed through the opening on switch cap plate. Align motor holes to blade holders and secure with screws provided, tighten screws securely. (Fig.
ATTACHING THE SWITCH CUP Step 1. Remove the 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) Step 2. Place the key holes on the switch cup plate over the 2 screws previously loosened from the mounting ring, turn switch cup plate until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. (Fig. 18) Step 3. Remove the screws from the switch cup plate.
9 OPERATING YOUR FAN Restore power to ceiling fan and test for proper operation. Speed settings for warm or cool weather depend on factors such as the room size. Ceiling height, number of fans, etc. The Reverse switch is located on the switch cup. Slide the switch to the Left for warm weather operation. Slide the switch to the Right for cool weather operation. NOTE: Wait for fan to stop before changing the setting of the slide switch.
WINTER OPERATION SUMMER OPERATION Fig 20 Fig 21
10 CARE OF YOUR FAN Here are some suggestions to help maintain your fan. 4. Use a lint free lightly damp cloth or duster to remove dust from the blades. 1. Because of the fan's natural movement some connections may become 5. There is no need to oil your fan. The motor has permanently lubricated loose. Check the support connections, brackets and blade attachments bearings. twice a year. Make sure they are secure. (It is not necessary to remove 6.
TROUBLESHOOTING SYMPTOM Fan will not start SOLUTION Check to make sure the wall switch is turned on. Check circuit fuses or breakers. Caution! Make sure the power is turned off before performing the following steps. Remove canopy and check wire connections. If using a remote controlled fan; check to see that the deep switches from transmitter and receiver are set to the same frequency code. Check wall control transmitter connections (if applicable).
12 SPECIFICATIONS These are typical readings. Your actual fan may vary. They do not include amps and wattage used by the light (s). Fan Size Speed Volts Amps Watts RPM 54" 120 Low Medium 120 120 High 0.24 0.39 0.59 11.6 30.2 70.5 59 105 164 CFM N.W. G.W. C.F. 2363 4040 6257 9.65 10.95 2.
63 4040 6257 11.6 30.2 70.5 204 134 89 Ceiling fan airflow is measured in cubic feet per minute (CFM). Power use is measured in watts.
