Floatation Raft FRP01 Original Instruction Manual Version B
FRP01 – FLOATATION RAFT Eliminate the need for man-entry. The floatation raft features three extremely powerful angled auxiliary LED ultra-bright light modules to provide enough light to illuminate pipes in excess of 2000mm Small enough to be lowered down most common sizes of manhole cover, the compact design allows inspection capabilities in pipes from 600mm.
Parts and Descriptions F E G D C A B H A A Guide Eyelet B Balance Plate C Camera Connector Protection Cap D LED Auxiliary Light Cluster E Lowering Loop F Pressure Valve Protection Cap G Strain Relief H Raft 04 Minicam Proteus Floatation Raft Version B
Connection of Cabling between Cable Reel and Raft Connect the cable reel cable to the back of the floatation raft as illustrated: D C A B 1 Plug the female plug of the cable reel (A) into the connector at the rear of the raft (B). Notice the orientation of the plug (C). 2 Turn the retaining ring (D) clockwise, as viewed from the cable, to lock the plug into the connector at the rear of the raft (B). The retaining ring is not able to unscrew itself during use, providing it is cleaned and maintained.
Disconnecting Cabling between Cable Reel and Raft Disconnect the cable reel cable from the back of the floatation raft as illustrated: 1 To unscrew the retaining ring you must pull the ring away from the body of the floatation raft before rotating anti-clockwise. NOTE! Always fit the protective caps when the raft or camera are not in use to protect from ingress of dirt and moisture.
Connection of Camera to Floatation Raft Connect the camera to the floatation raft as illustrated: C D B A 1 Ensure the connections are free of debris, dirt and moisture. 2 Ensure the locking ring (A) is rotated fully clockwise, as viewed in the diagram. 3 Notice the orientation of the camera (B). Orientation pin locates here (C). Fit the camera. 4 Turn the locking ring (A) anti-clockwise, as viewed in the diagram, to lock the camera onto the raft.
Floatation Raft with cable and camera connected Information and Care Maintenance Ensure all parts are free from debris and dirt.
Instructions for pressurising the FRP01 Floatation Raft 1 Connect the PROTEUS™ inspection system and apply power. 2 Unscrew the pressure valve protection cap (1) 1 3 Screw on the pressure valve (2). 2 4 Set the pressure regulator for the CO2 or nitrogen to 10 PSI.
5 Ensure the floatation raft pressure is within the acceptable range by checking the pressure gauge on the control unit. An example is shown below. Refer to the CCU section of this manual on specific instructions on how to access the pressure gauges. Image shows an example of the control unit raft pressure gauge: 6 Remove the pressure valve (2). 7 Refit the pressure valve protection cap (1) .
Technical Details - FRP01 Product ID: Dimensions: Weight (without camera): IP Rating: Version B FRP01 680 x 420 x 200mm (L x W x H) 5.8Kg (12.
WEEE Statement Under the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment are obligated to take back such products at the end of their useful life. Minicam will comply with the product take back requirements at the end of life of Minicam products that are sold into the EU.
Batteries As a producer of industrial batteries under the Waste Batteries and Accumulators Regulations 2009, we Minicam produce Lithium Ion batteries. We are obliged to take back free of charge, waste industrial batteries supplied to an end user for treatment and recycling. We are required to do this in any calendar year we place new industrial batteries on the market.
Product Serial Numbers Enter your product serial numbers below for future reference: PRODUCT SERIAL NUMBER Floatation Raft FRP01 14 Minicam Proteus Floatation Raft Version B
Notes Version B Minicam Proteus Floatation Raft 15
Minicam Ltd Unit 4, Yew Tree Way, Stonecross Park, Golborne, Warrington, WA3 3JD United Kingdom ©2022 Minicam. All rights reserved. Specifications subject to change without notice. Minicam is a Halma Company. DESIGN 1220 Tel: +44 (0)1942 270524 Email: info@minicam.co.uk www.minicamgroup.
