0X True Day/Night PTZ Dome Mini PTZ Dome Camera HDT HDTX User Guide Document 800-06705 - Rev A - 12/10
Revisions 2 Issue Date Revisions A 6/10 New document. 12/10 This version is for Ver. 1.5 firmware.
Mini PTZ Dome Camera User Guide Important Notice The Mini PTZ Dome Camera only supports Pelco-D protocol. When Mini PTZ Dome of Pelco-D protocol is controlled by a Honeywell RapidEye or Fusion Series DVR, please use Focus Near and Focus Far buttons instead of OSD operation buttons in DVR’s user interface to select or close OSD menu items. When Mini PTZ Dome of Pelco-D protocol is controlled by a Honeywell RapidEye Series DVR, please run pattern / swing / group functions only in the OSD menu.
Contents Contents 1 2 3 4 Introduction ………………………………………………………………………………………………….. 11 Features ………………………………………………………………………………………………………. Parts List …………………………..………………………………………………………………………….. Main Part Description ………………………………………………………………………………………... 11 13 14 Installation …………………………………………………………………………………………………… 15 DIP Switch Setup ……………………………………………………………………………………………..
Mini PTZ Dome Camera User Guide Figures Figure 1-1 Parts Overview ..…….....……………………………………………………………………………. 13 Figure 2-1 Location of DIP Switch ……………………………………………………………………………… 14 Figure 2-2 Terminal Resistor Setup for Multi-Drop Connections ..………………………………………... 16 Figure 2-3 Typical Connection Diagram ……………………………………………….................................. 22 Figure 2-4 Connection of RS-485 Communication ………………………………………………..................
Tables Tables 6 Table 1-1 Example of Preset Parameters .……………………………………………………………………. 10 Table 2-1 Example of Camera ID Setup ….…………………………………………………………………... 14 Table 2-2 Communication Protocol Setup ….………………..……………………………………………... 15 Table 2-3 Pin Description of Main Cable ……………………………………............................................... 22 Table 2-4 Power Consumption ………………………………………………............................................... 22 Table 4-1 Factory Default Setting ………………………………………………........
Mini PTZ Dome Camera User Guide Warnings and Safeguards Explanation of Warnings WARNING! The exclamation point in an octagon is a WARNING. Failure to take or avoid a specific action could result in physical harm to a person or irreparable damage to equipment.
Warnings and Safeguards FCC Compliance Information to User: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Mini PTZ Dome Camera User Guide Important Safety Instructions BEFORE OPERATING OR INSTALLING THE UNIT, READ AND FOLLOW ALL INSTRUCTIONS. After Installation, retain the safety and operating instructions for future reference. 1. HEED WARNINGS – Follow all warnings on the unit and in the operating instructions. 2. ATTACHMENTS / ACCESSORIES - Use only the attachments/accessories specified by the manufacturer. 3.
Warranty and Service Warranty and Service Subject to the terms and conditions listed on the Product Warranty Card, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Honeywell Video Systems product, please call Customer Service for assistance or to request a Return Merchandise Authorization (RMA) number.
Mini PTZ Dome Camera User Guide Introduction Features Powerful Zoom Camera & Setup Options z Sony 1/4 inch Interline Transfer CCD image sensor z 10x optical zoom/digital zoom (maximum 100x zoom magnification) z True Day/Night (TDN) capability z Auto-focus, manual focus, semi-auto focus modes available z Multiple setup options using On-Screen Display (OSD) Powerful Pan/Tilt Functions z High-speed pan/tilt motion up to 360° per second z Vector Drive technology allows faster time to target
Introduction z Maximum 8 sets of Swing are programmable. The Swing function causes the camera to move repetitively between two preset positions at programmed speeds. z Maximum 4 Patterns are programmable. The Pattern function causes the camera to memorize the path (curve path) created by the controller joystick and to duplicate it as closely as possible. z Maximum 8 sets of Groups are programmable.
Mini PTZ Dome Camera User Guide Parts List Product & Accessories z Main Body, Surface Mount Bracket and In-Ceiling Plate z Default Accessories [ Main Cable, Rubber Gasket, Screws: Tapping M4×25, Machine M3×6, Machine M3×8, Machine M4×50, M4 Nut ] Brackets (Optional) z Wall Mount Bracket z Ceiling Mount Bracket [ Screws : Machine M3×8, Hex Lag #14×50 ] Mounts [ Screws : Machine M3×8, Tapping M4×25 ] Description z HDTW 10× True Day/Night PTZ Wall Mount Bracket z HDTC 10× True Day/Night PTZ Ce
Introduction Main Part Description Figure 1-1 Parts Overview Surface Mount Bracket Mounting Screw Hole Main Connector Dome Cover Assembly Stud Dome Cover Lock-up Screw DIP Switch Dome Cover z Dome Cover To protect the dome cover from scratches and dust, do not remove the protective vinyl from the dome cover until the installation is complete.
Mini PTZ Dome Camera User Guide Installation DIP Switch Setup Before installing the camera, set up the DIP switch to configure the camera ID and the communication protocol. Figure 2-1 Location of DIP Switch Camera ID Setup ON z ON 1 ID numbers of cameras are set up with binary numbers. See the examples shown below.
Installation z The camera ID range is “1~255”. Camera ID must not be “0”! z The factory default of the camera ID is “1”. z Match the camera ID with the Cam ID setting of your DVR or controller to control the camera. z If you are connecting a single camera to a controller, and the cable you are using to connect the camera to the controller is so long that the camera is out of control, terminate the camera.
Mini PTZ Dome Camera User Guide Terminal Resistor Setup ON The terminal resistor is used in the following cases: ON 1 2 3 4 z Case 1: The control cable length between a camera and a controller is very long (1:1 Connection) If the communication cable length is over 300m with one shielded twisted pair cable or CAT5 cable (this distance may vary when using different impedance cables), the electrical signal will bound in the terminal point. This reflected signal causes distortion of original signal.
Installation In-Ceiling Mount Installation c Remove the ceiling tile from the ceiling and attach d Install the main body with the In-Ceiling Plate, the the Guide Pattern to the ceiling tile. Then cut a hole three screws (M4x50) and the three nuts (M4). whose diameter is 116 mm and three holes for Then install the ceiling tile to the ceiling and M4x30 on the ceiling tile. connect the main cable to the main port.
Mini PTZ Dome Camera User Guide Installation with Surface Mount Bracket c Remove the ceiling tile from the ceiling and cut a d Prepare the surface mount bracket. Pull the main hole whose diameter is 30-40mm on the ceiling tile cable for the system as below. Attach the surface to pass the wires and cables through to the upside mount bracket to the mounting surface. (Tapping of the ceiling.
Installation Installation with Ceiling Mount Bracket c Remove the ceiling tile from the ceiling and cut a d Pull the main cable for the system as below. Turn hole whose diameter is 30—40 mm on the ceiling the bracket adapter on its axis in a clockwise tile and attach the ceiling mount bracket on it. direction until it stops and then attach the surface (Tapping M4×25) mount bracket.
Mini PTZ Dome Camera User Guide Important Notice z Before starting the installation, make sure that the camera ID and protocol are set up properly. z When the wiring access hole on the side of the surface mount bracket is not used, make sure that the hole is properly sealed with the supplied rubber gasket.
Installation Installation with Wall Mount Bracket c Make a hole whose diameter is 30-40 mm on the d Pull the main cable for the system as below. Turn mounting surface. Then prepare the wall mount the bracket adapter on its axis in a clockwise bracket. Pull the main cable for the system as direction until it stops and then attach the surface below. Attach the wall mount bracket to the mount bracket. (Machine M3×8) mounting surface.
Mini PTZ Dome Camera User Guide Wiring and Cabling Figure 2-3 Typical Connection Diagram Power BNC Main Cable Monitor RS-485 Controller / DVR Port Description Table 2-3 Pin Description of Main Cable Port Pin Number (RJ45) Connector / Wire Color 1 Signal BNC Connector 2,4 5 Red RS-485 + 3 Yellow RS-485 − 7 Power Jack (Orange) Power + 6,8 Power Jack (White) Power - Power Description z Carefully check the voltage and current capacity of the rated power.
Installation RS-485 Communication z For PTZ control, connect the cable(s) to your keyboard or DVR. Note that the total length of the communication cable between a controller and the camera(s) on the same communication line must be less than 4,000 feet (1,200 meters). Figure 2-4 Connection of RS-485 Communication Controller / DVR + - RS-485 + #1 Video z 24 Use BNC coaxial cable only.
Mini PTZ Dome Camera User Guide Operation Checking Points before Operation z Before turning on the system, check if the wire(s) and cable(s) are connected properly. z Check if the camera ID on the controller is properly selected. The camera ID must be identical to that of the target camera. The camera ID can be checked by reading the DIP switch of the camera or the OSD. z If your controller supports multiple protocols, the protocol must be changed to Pelco-D protocol.
Operation OSD Menu z Function Using the OSD menu, the system can be properly configured for each application. z Entering into OSD Go Preset [95] Reserved Presets (Hot Keys) Some Preset numbers are reserved to change some parameters without entering the OSD menu.
Mini PTZ Dome Camera User Guide Preset z Function Maximum 127 positions are programmable. Any number between 1 and 128 can be assigned to a Preset, except 95. Preset 95 is reserved for entering the OSD menu. Camera parameters such as White Balance, Auto Exposure and others can be set up independently and each preset can have its own parameter values independently from other presets.
Operation Pattern z Function This function causes the camera to memorize the curve path created by the controller joystick and to duplicate that trajectory as closely as possible. Maximum four Patterns are programmable and maximum 1,200 communication commands can be programmed in a pattern. z Setting Patterns A Pattern can be created by the following methods: Method 1) [Pattern no.] { The Pattern programming window appears on the monitor as below.
Mini PTZ Dome Camera User Guide Group z Function This function causes the camera to memorize a combination of Presets, Patterns, and/or Swings, and to run them repetitively in sequence. Maximum eight sets of Groups are programmable. Each Group can have up to 20 actions combining Presets, Patterns, and Swings. Dwell time between actions, Preset speeds, and the number of times Patterns and Swings are repeated, can be set up for each Group. Dwell Time Preset 1 Pattern 1 Swing 1 Max.
Operation Other Functions z Power Up Action This setting defines a specific activity (Preset, Pattern, Swing, Group) to be performed in the event that the power to the camera is cycled. This function enables the user to resume, after turning on power, the last action being executed before turning off the power. Please note that jog actions are not available to resume.
Mini PTZ Dome Camera User Guide OSD Display Figure 3-1 Preset Label Camera ID OSD display in main screen LABEL12345 CAM 1 PRESET1 Action Title 15/4/x1/N P/T/Z Information z P/T/Z Information Displays the amount of pan from zero degrees vertical, the amount of tilt from zero degrees horizontal, the current compass direction, and the amount of zoom magnification. z Camera ID Displays the selected camera ID (address).
OSD Menu OSD Menu Quick Programming Guide z The menu items with < > always have sub-menus. z To go to sub-menus or make the cursor move to the right, press the NEAR key. z To go to previous upper level menus, press the FAR key. z To make a selection, press the NEAR key z To cancel a selection, press the FAR key z To move the cursor in the menu, move the joystick to move in an Up/Down direction or in a Left/Right direction. z To change a value, move the joystick up or down.
Mini PTZ Dome Camera User Guide Display Setup DISPLAY SETUP -----------------------CAMERA ID ON PTZ INFORMATION AUTO ACTION TITLE AUTO PRESET LABEL AUTO ALARM I/O AUTO BACK EXIT Display setup allows you to program how labels are displayed on the monitor. In case of AUTO, the labels are displayed on the monitor when there are any changes in parameters. z Camera ID [ON/OFF] Displays the selected camera ID (address).
OSD Menu Camera Setup ZOOM CAMERA SETUP -----------------------FOCUS MODE SEMIAUTO DIGITAL ZOOM ON IMAGE FLIP OFF SHARPNESS 16 The Zoom Camera Setup menu sets the general functions of the zoom camera module. z Focus Mode [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode. { SEMIAUTO mode BACK EXIT This mode automatically exchanges focus modes between Manual Focus mode and Auto Focus mode by operation.
Mini PTZ Dome Camera User Guide White Balance Setup WB SETUP - GLOBAL -----------------------WB MODE AUTO RED ADJUST --BLUE ADJUST --- z WB Mode [AUTO/MANUAL] Retains color balance over a color temperature range. In Auto mode, this feature automatically processes the viewed image. In Manual mode, red and blue levels can be set up manually. BACK EXIT z Red Adjust [10~50] Adjusts the picture output in the red range. z Blue Adjust [10~60] Adjusts the picture output in the blue range.
OSD Menu z IRIS [AUTO/MANUAL(0~100)] Sets Iris to operate automatically or at a user-defined level. Auto Iris is the lens function that automatically opens or closes the iris in response to changing light conditions. If Iris is set to Auto, Iris has higher priority in adjusting Auto Exposure, and Shutter Speed is fixed. If Iris is set to Manual, Iris is fixed and has lower priority in adjusting Auto Exposure. The Iris level range is 0 ~ 100. z Shutter Speed [ESC/A.
Mini PTZ Dome Camera User Guide Motion Setup MOTION SETUP -----------------------MOTION LOCK OFF PWR UP ACTION ON AUTO FLIP ON JOG MAX SPEED 120/SEC JOG DIRECTION INVERSE FRZ IN PRESET OFF BACK EXIT Sets the general functions of pan/tilt motions. z Motion Lock [ON/OFF] If Motion Lock is set to ON, it is impossible to set up or delete Preset, Swing, Pattern and Group. It is only possible to run those functions z Power Up Action [ON/OFF] Refer to “Other Functions" section.
OSD Menu Parking Action Setup PARKING ACTION SETUP -----------------------PARK ENABLE OFF WAIT TIME 00:10:00 PARK ACTION HOME This feature allows the camera to begin a specified action after a programmed time of inactivity. z Park Enable [ON/OFF] If Park Enable is set to ON, the camera runs an assigned function automatically if no PTZ command is received during the programmed Wait Time. BACK EXIT z Wait Time [1~59 sec. / 1~180 min.] Wait Time can be programmed from 1 second to 180 minutes.
Mini PTZ Dome Camera User Guide Preset Setup PRESET SETUP -----------------------PRESET NO. 1 CLR PRESET CAM ADJUST z Preset Number [1~128] Selects a Preset number to set up. If a selected Preset is already defined, the camera moves to CANCEL the pre-defined position and parameters such as LABEL123 GLOBAL Label and Cam Adjust show on the monitor. If a selected Preset is not defined, UNDEFINED shows on the monitor.
OSD Menu Preset Scene Setup EDIT SCENE - PRESET 1 ------------------------ c Use the Joystick to move the camera to a desired position. d Save the Preset position by pressing the NEAR key e Press the FAR key to cancel targeting the Preset position. MOVE TO TARGET POSITION [NEAR:SAVE /FAR:CANCEL] Preset Label Setup EDIT LABEL - PRESET 1 -----------------------[ ] ---------1234567890 OK ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz<>-/:.
Mini PTZ Dome Camera User Guide Swing Setup SWING SETUP -----------------------SWING NO. 1 1ST POS. NOT USED 2ND POS. NOT USED SWING SPEED CLEAR SWING RUN SWING 30/SEC CANCEL BACK EXIT z Swing Number [1~8] Selects a Swing number to edit. If the selected Swing is not defined, NOT USED is displayed in the 1st Position and the 2nd Position. z 1st Position 2nd Position [PRESET 1~128] Sets the two positions for a Swing function.
OSD Menu Pattern Setup PATTERN SETUP -----------------------PATTERN NO. 1 UNDEFINED CLR PATTERN CANCEL RUN PATTERN z Pattern Number [1~4 ] Selects a Pattern number to edit. If the selected pattern number is not defined, UNDEFINED is displayed under the selected Pattern number. z Clear Pattern [CANCEL/OK] Deletes the data of the selected Pattern. BACK EXIT z Run Pattern Runs the Pattern for test purposes to check if it works properly. z Edit Pattern Edits the selected Pattern.
Mini PTZ Dome Camera User Guide Group Setup GROUP SETUP -----------------------GROUP NO. 1 UNDEFINED CLEAR GROUP CANCEL RUN GROUP z Group Number [1~8] Selects a Group number to edit. If the selected Group number is not defined, UNDEFINED is displayed under the selected Group number. z Clear Group BACK EXIT [CANCEL/OK] Deletes the data of the selected Group. z Run Group Runs the Group for the test purposes to check if it works properly. z Edit Group Edits the selected Group.
OSD Menu EDIT GROUP 1 -----------------------NO ACTION ### DWELL OPT -----------------------1 PRESET 1 00:03 360 2 NONE 3 NONE 4 NONE 5 NONE -----------------------SAVE [ :MOVE CURSOR] CANCEL [ :CHANGE VAL.] f Edit the Action, Dwell and Option by moving the cursor.
Mini PTZ Dome Camera User Guide System Initialization SYSTEM INITIALIZE -----------------------CLEAR ALL DATA NO CLR DISPLAY SET NO CLR CAMERA SET NO CLR MOTION SET NO CLR EDIT DATA NO REBOOT CAMERA NO REBOOT SYSTEM NO BACK EXIT z Clear All Data Deletes all configuration data and resets the system is set to the factory default. z Clear Display Set Initializes all the configuration data for Display. z Clear Camera Set Initializes all the configuration data for Camera.
Appendix A Specifications Appendix A Specifications CAMERA PART Video Signal Format Image Sensor PAL 1/4'' Interline Transfer CCD Total Pixels 811(H)×508(V) 410K 795(H)×596(V) 470K Effective Pixels 768(H)×494(V) 380K 752(H)×582(V) 440K Horizontal Resolution 470 TV Lines (Color), 540 TV Lines (B/W) Video Signal-to-Noise 50 dB (AGC Off) Zoom ×10 Optical Zoom, ×10 Digital Zoom Focal Length F1.8, f=3.8~38mm Angle of View H: 51.2°(Wide)~5.58°(Tele) / V: 39.3°(Wide)~4.
Mini PTZ Dome Camera User Guide MECHANISM PART Movement Pan 360° (Endless) Range Tilt 90° Preset Speed 360°/sec. Jog 0.05 ~ 360°/sec. (Proportional to Zoom) Swing 1~ 180°/sec. ± 0.2° Preset Accuracy Preset 127 Presets (Label, Independent Camera Parameter Setting) Pattern 4 Patterns [1200 Commands (Approx. 5 Minutes) / Pattern] Swing 8 Swings Group 8 Groups (Max.
Dimensions Appendix B Dimensions z Main Body z Surface Mount Type 129.5 20 83.5 84.5 4- 5 107.5 107.5 z Wall Mount Type 3- 6 102 78 86 210.8 65 199.5 50 75 z Ceiling Mount Type 58 46 142.5 140 129.
Honeywell Security Group (Head Office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA www.honeywellvideo.com +1.800.796.2288 Honeywell Security Group Europe/South Africa Aston Fields Road, Whitehouse Industrial Estate Runcorn, Cheshire, WA7 3DL, UK www.honeywell.com/security/uk +44.01928.754028 Honeywell Security Group Caribbean/Latin America 9315 NW 112th Ave. Miami, FL 33178, USA www.honeywellvideo.com +1.305.805.
