Mini Speed Dome Camera INSTRUCTION MANUAL PAL NTSC DOME 4.5" 100X ZOOM DAY & NIGHT ★ ON SCREEN DISPLAY 360 360 /sec 0.
CAUTl0N RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTl0N：TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS. N0 USER SERVICEABLE PARTS INSlDE. REFER SERVICING TO QUALIFIED SERVICE PERSONAL. This lightning flash with arrowhead symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
NOTICE Important Safeguard 1. Read Instructions Read all of the safety and operating instructions before using the product. 2. Retain Instructions Save these instructions for future reference. 3. Attachments／Accessories Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards,damage product and void warranty. 4. Water and Moisture Do not use this product near water or moisture. 5.
CONTENTS 1 Introduction Features 4 Pr od uct ＆Accessor i es 6 2 Installation DIP Switch Setup 7 Cabling 9 3 Operation Checking Before Operation 11 Preset and Pattern Function Pre-Check 11 Start OSD Menu 12 Reserved Preset 12 Preset 13 Swing 13 Pattern 14 Group Other Functions OSD Display of Main Screen 4 16 17 How to use 0SD Menu General Rules of Menu Operation 18 Main Menu 18 Display Menu for Main Screen 19 Privacy Zone Mask Setup 20 Camera Module Setup 21 Motion Se
100X ZOOM DAY & NIGHT 360 360 /sec 0.05 /sec CONTINUOUS SPEED LOW SPEED VECTOR MOTION ★ INTRODUCTION 1 F ea t u r es Camera Specifications CCD Sensor :1/4"Interline Transfer CCD Zoom Magnification : x 10 Optical Zoom, x 10 Digital Zoom(Max x 100 Zoom) Day & Night Function Various Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus. Independent＆Simultaneous Camera Characteristic Setup in Preset operation Powerful Pan/Tilt Functions Max.
AL ARM 41N INTRODUCTION 1 OSD (On Screen Display) Menu OSD menu is provided to display the status of camera and to configuie the functions interactively. The information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be displayed on screen. I/O Functions (Not Avalible) To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo coupler. The signal range of sensor input is from DC 11.5 to 14.0 volts to adopt various applications.
INTRODUCTION 1 Product & Accessories Assembly Speed Dome Mounting Base Options Screws x 3 Screws x 3 Ceiling Bracket Thread Connector Speed Dome Pendant Bracket Groove Mounting Base Screws x 3 Speed Dome Wall Mount Bracket 6 Spee d Dome Camera Instruction Manual
2 INSTALLATION DIP Switch Setup Before you install the cam era, you should set the DIP switches to configure the camera ID, communication protocol. Communication Prot ocol Camera ID ADDRESS (ID) OPTIONS ON ON 1 1 PIN 2 3 2 4 3 FUNC. PROTOCOL ON Refer to PA L the Manual NTSC OFF 1 4 3 4 5 6 7 8 1 2 3 4 5 6 7 8 FUNC.
INSTALLATION 2 Communication Protocol Setup Select the appropriate Protocol with DIP switch combination. ON ON Switch State 1 2 3 Protocol 4 P0 (Pin 1) P1 (Pin 2) OFF OFF PELCO- D, 2400 bps ON OFF PELCO- D, 9600 bps OFF ON PELCO- P, 4800 bps ON ON PELCO- P, 9600 bps If you want to control using DVR or P/T controller, their protocol must be identical to camera. Otherwise, you can not control the camera.
INSTALLATION 2 Cabling B NC Moinitor RS-485( - ) Controller/DVR RS-485( + ) Power Speed Dome Cabling Terminal Block Power Connection Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the back of main unit. Roated Power DC 12V Input Voltage Range D C 11V ~18 V Current Consumption 0.8A RS-485 Communication For PTZ control, connect this line to keyboard and DVR.
INSTALLATION 2 Video Connection Connect with BNC coaxial cable. Alarm input Conection (Not Avalible) Sensor Input Intemal +5V-12V + In COM+ In 1- Sensor 1 Output + - In 4- Sensor 4 Output + - Before connecting sensors, check driving voltage and output signal type of the sensor. Since output singal types of the sensors are divided into open collector and voltage output tye in general, the cabling must be done properly after considering these typed.
OPERATION 3 Check points before operation Before power is applied, please check the cables carefully. The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked by reading DIP switch of the camera． If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
ON SCREEN DISPLAY OPERATION 123 3 Starting OSD Menu Function Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be configured for each application. Enter Menu Press + Preset Number [95] + Reserved Preset Description Some Preset numbers are reserved to special functions.
PRESET 128 2 SWING 8 128 OPERATION 1 3 Pr esett Function Max 255 positions can be stored as Preset position. The Preset number can be assigned from 1 to 255, but 95 is reserved for starting OSD menu. Camera characteristics (Le. White Balance, Auto Exposure) can be set up independently for each preset. Label should be blank and ”Camera Adjust”should be set to ”GLOBAL” as default.
PATTERN 4 OPERATION 3 Pattern Function Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of controller for assigned time and revives the path exactly as it memorized. 4 Patterns are available and Maximum 1200 communication commands can be stored in a pattern. Setup Pattern →→ Pattern editing screen is displayed as bellow.
GROUP 8 2 1 3 OPERATION 3 Group Function The group function allows runmng sequence of Presets, Pattern and/or Swings Max 8 group can be stored. Each group can have max 20 action entities which can be preset, pattern or swing Preset speed can be set up and the repeat number of Pattern＆Swing can be set up in Group setup. Dwell time between actions can be set up also.
AL ARM 4 IN PRIVACY ZONE OPERATION 3 Other Functions Power Up Action This function enables to resume the last action executed before power down. Most of actions such as Preset, Pattern, Swing and Group are available for this functlon but jog actions are not available to resume． Auto Flip In case that tilt angle arrives at the top of tilt orbit (90º), zoom module camera keep moving to opposite tilt direction (180º) to keep tracing targets.
ON SCREEN DISPLAY OPERATION 123 3 OSD Display of Main Screen Preset Label LABEL 12345 Image Flip Camera ID F CAM 1 PRESET1 I:1--4 15/ 4/ X 1/ N Action Title Alarm Information P/T/Z Information P/T/Z Information Current Pan/Tilt angle in degree, zoom magnification and a compass direction. Camera ID Current Camera ID(Address). Action Title Follovangs are possible Action-Titles and their meaning.
HOW TO USE OSD MENU 4 General Rules of Key Operation for Menu The menu items surrounded with ( ) always has its sub menu. For aIl menu level, to go into sub menu, press NEAR key． To go to up-one-level menu, press FAR key. T0 mave from items to item in the menu, use joystick in the Up/Down or Left/Right. To change a value of an item, use Up/Down of the joystick in the controller. Press NEAR key to save values and Press FAR key to cancel Values.
HOW TO USE OSD MENU 4 Display Setup D I S P L AY S E T U P CAMERA ID ON P T Z I N F O R M AT I O N A U T O ACTION TITLE AUTO PRESET LABEL AUTO ALARM INPUT AUTO < P R I VA C Y Z O N E > BACK EXIT This menu defines Enable/Disable of OSD display on Main Screen. If an item is set to be AUTO, the item is displayed only when the value of it is changed.
PRIVACY ZONE HOW TO USE OSD MENU 4 PRIVACY ZONE MASK Setup → Select area in image to mask. PRIVACY ZONE MASK NO D I S P L AY CLEAR MASK 1 UNDEFINED OFF CANCEL Mask No [1~4] Select Mask number. If the selected mask has already data, camera moves as it was set. Otherwise, “UNDEFINED” will be displayed BACK EXIT under “Mask No”. Display [ON/OFE] Sets if camera makes mask shows or not on images Clear Mask [CANCEL/OK] Deletes data in the selected mask NO .
100X ZOOM HOW TO USE OSD MENU 4 CAMERA SETUP → ZOOM CAMERA SETUP FOCUS MODE S E M I A U TO D I G I TA L Z O O M O N LINE LOCK OFF Setup the general functions of zoom camera module Focus Mode [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode． SEMIAUTO Mode This mode exchanges focus mode automatically between Manual Focus mode and Auto Focus mode BACK EXIT Manual Focus mode activates in preset operation and Auto Focus mode acti
HOW TO USE OSD MENU 4 Auto Exposure Setup →→ AE SETUP - BACKLIGHT D AY / N I G H T BRIGHTNESS IRIS SHUTTER AGC SSNR SENS -UP BACK EXIT GLOBAL OFF AUTOI 25 AUTO ESC NORMAL MIDDLE Backlight [ON/OFF] Sets Bacldight Compensation Day/Night [AUTO1/AUTO2 DAY/NIGHT] AUTO1 exchanges Day/Night mode faster than AUTO2. Brightness [0∼100] Adjusts brightness of images.
HOW TO USE OSD MENU 4 Motion Setup → Setup the general functions of Pan/Tilt motions. MOTION SETUP OFF MOTION LOCK ON PWR UP ACTION ON AUTO FLIP JOG MAX SPEED 120/SEC INVERSE JOG DIRECTION OFF FRZ IN PRESET BACK EXIT Motion Lock [ON/OFF] Group. It is possible only to run those functions. To set up and delete those functions, enter into OSD menu. Power Up Action [ON/OFF] Refer to "Other Functions" section.
AL ARM 4 IN HOW TO USE OSD MENU 4 Parking Action Setup →→ PA R K I N G A C T I O N PA R K E N A B L E WA I T T I M E PA R K A C T I O N SETUP OFF 00:10:00 HOME If Park Enable is set to ON, camera runs assigned function automatically if there is no PTZ command during assigned ''Wait Time''. Park Enable [ON/OFF] Wait Time [1 minute∼4 hour] The time is displayed with "hh:mm:ss" format BACK EXIT and you can change this by 1 min unit.
PRESET 128 2 128 HOW TO USE OSD MENU 1 4 PRESET Setup → Preset Number PRESET SETUP PRESET NO. CLR PRESET CAM ADJUST If a selected preset is already defined, camera 1 moves to pre- defined position and preset CANCEL characteristics such as Label and Relay Outputs LABEL123 GLOBAL BACK EXIT [1~128] (Except [95]) show on monitor. If a selected preset is not defined. "UNDEFINED" shows on monitor.
HOW TO USE OSD MENU 4 Edi t Pr eset Scene →→ EDIT SCENE - PRESET 1 1 Using Joystick, move camera to desired position. 2 By pressing NEAR key, save current PTZ data. 3 Press FAR key to cancel. M O V E T O TA R G E T P O S I T I O N [ N E A R : S AV E / FA R : C A N C E L ] Edi t Pr eset Label Dome Camera Setup>→→ EDIT LABEL - PRESET 1 1 Edits label to show on monitor when camera arrives at presets.
SWING 8 HOW TO USE OSD MENU 4 Swing Setup → Swing N umber SWING SETUP SWING NO . 1 S T POS. 2ND POS. Selects Swing number to edit.
PATTERN 4 HOW TO USE OSD MENU 4 Pattern Setup → Pattern Number PAT T E R N S E T U P [1~4] Selects Pattern number to edit. PAT T E R B N O . 1 UNDEFINED C L R PAT T E R N CANCEL If a selected pattern number is not defined, "UNDEFINED" will be displayed under selected pattern number. Clear Pattern BACK EXIT [CANCEL/OK] Deletes data in current pattern Edit Patternk Starts editing pattern.
GROUP 8 2 1 3 HOW TO USE OSD MENU 4 Group Setup → Cr oup N umber [1~8] GROUP SETUP Selects Group number to edit. GROUP NO . 1 UNDEFINED CANCEL CLEAR GROUP If a selected Group number is not defined, "UNDEFINED" will be displayed under selected Group number. Clear Gr oup BACK EXIT [CANCEL/OK] Deletes data in current Group Edit Gr oup Starts editing Group.
HOW TO USE OSD MENU EDIT GROUP 1 4 4 Set up items such as Action, ###, Dwell and OPT. 5 After finishing setting up a Action, Press Near key to one-upper-level NO ACTION ### DWELL OPT 1 00 : 03 360 1 PRESET 2 NONE 3 NONE 4 NONE 5 NONE ▲ ▲ ［ ：MOVE CURSOR [ ▲ CANCEL ［ ▲ ：CHANGE VA L. [ SAVE EDIT GROUP 1 menu (Step ②). Move cursor Up/ Down to select Action NO ACTION ### DWELL OPT → 1 PRESET number and repeat Step ②~Step ④ to edit selected Group .
HOW TO USE OSD MENU 4 System Initialize SYSTEM I N I T I A L I Z E → CLEAR ALL DATA CLR DISPLAY SET NO CLR CAMERA SET NO NO CLR MOTION SET NO CLR EDIT DATA NO REBOOT CAMERA NO REBOOT S Y S T E M NO SAVE CANCEL Clear All Data Deletes all configuration data such as display. camera, motion setup and so on.
DOME 4.5 " 100X ZOOM DAY & NIGHT SPECIFICATIONS ★ Video Signal System NTSC PAL 1/4"Interline Transfer CCD CCD Max. Pixels 811(H)× 508(V)410K 795(H)× 596(V)470K Effective Pixels 768(H)×494(V)380K 752(H)×582(V)440K Horizontal Res. 500 TV Line(Color),570 TV Line(B/W) 50 dB (AGC Off) S/N Ration Zoom ×10 Optical zoom, ×10 Digital Zoom F1.8,f=3.8~38mm Focal length Min. Camera Illumination 0.7 Lux(Color) / 0.
SPECIFICATIONS 5 Dimension Ceiling Bracket Pendant Bracket 187 mm 400 mm 223 mm ͫ 128 mm ͫ 1 27mm Wall Mount Bracket 136 204.4 mm 136 mm 162.3 mm 118 200.7 mm 80 ͫ 107.7 ͫ 1 27mm U nit (mm) Spee d Dome Camera Instruction Manual All Rights Reserved Reprodution All or Part without Permission Prohibited. Invoice.
