User Manual
Table Of Contents
- 08-0308 - Manual Cover.pdf
- 0070-10-0690-01 Panorama Operations Maual with Telepack 2.4 - CH16 REVISED2.pdf
- Foreword
- Warnings, Precautions and Notes
- Indications for Use
- Unpacking Information
- Symbols and Descriptions
- Technical Support
- 1.0 System Overview
- 1.1 Components of the Panorama System
- 1.2 Licensing Key
- 1.3 Supported Devices
- 1.3.1 Panorama Central Station
- 1.3.2 Panorama ViewStation and WorkStation
- 1.3.3 Panorama Telemetry Server
- 1.3.4 Panorama Wireless Transceiver
- 1.3.5 Panorama Gateway
- 1.3.6 Panorama Web Viewer
- 1.3.7 Passport 2® Bedside Monitor
- 1.3.8 Spectrum™ Bedside Monitor
- 1.3.9 Spectrum OR™ Bedside Monitor
- 1.3.10 Panorama Telepack
- 1.3.11 Network Printer
- 1.4 Troubleshooting
- 2.0 Getting Started
- 3.0 Alarm Behavior
- 4.0 Arrhythmia and ST Analysis
- 5.0 Patient Setup Functions
- 5.1 Demographics Tab
- 5.2 Transfer Tab
- 5.3 Discharge Tab
- 5.4 Display Tab
- 5.5 Standby Tab
- 5.6 Wave Gain Tab (Patient)
- 5.7 Print Setup Tab (Patient)
- 6.0 Patient Alarm Functions
- 7.0 Views
- 7.1 Bedside Tab
- 7.2 Trends Tab
- 7.3 Events Tab
- 7.4 Disclosure Tab
- 7.4.1 Accessing the Disclosure Tab
- 7.4.2 Disclosure Tab (Waveforms View)
- 7.4.2.1 Accessing the Waveforms View
- 7.4.2.2 Components of the Waveforms View
- 7.4.2.3 Navigating in the Waveforms View of the Disclosure Tab
- 7.4.2.4 ST Button
- 7.4.2.5 Comments Dialog Box (Optional)
- 7.4.2.6 Sidebar Buttons
- 7.4.2.7 Printing a Full Disclosure Zoom In Report from the Waveforms View
- 7.4.2.8 Troubleshooting
- 7.5 ST Tab
- 8.0 Report Functions
- 8.1 Patient Reports Tab
- 8.2 System Reports Tab
- 8.3 Print Status Tab
- 8.4 Additional Reports
- 9.0 System Setup Functions
- 9.1 Parameter Color Tab
- 9.2 Touch Screen Tab
- 9.3 Installation Setup Tab
- 9.4 Care Group Tab
- 9.5 Volume Tab
- 9.6 System Alarms Tab
- 9.7 Passwords Tab
- 9.8 Equipment Setup Tab
- 9.9 More Tab
- 9.10 Previous Tab
- 9.11 Date/Time Tab
- 9.12 Print Setup Tab (System)
- 9.13 Unit Priorities Tab
- 9.14 Unit Choices Tab
- 9.15 Wave Gain Tab (System)
- 9.16 Wireless Tab
- 10.0 Telepack (Optional)
- 11.0 User Maintenance
- 12.0 Parameter Specifications
- 12.1 Parameter Specifications
- 12.1.1 Heart Rate: HR
- 12.1.2 Respiration: Resp
- 12.1.3 NIBP
- 12.1.4 SpO2
- 12.1.5 Nonin SpO2
- 12.1.6 IBP: mmHg
- 12.1.7 CO2
- 12.1.8 O2
- 12.1.9 INSP/ET O2
- 12.1.10 N2O
- 12.1.11 Anesthetic Agents: Iso, Enf, Des, Sev, Hal, Agent
- 12.1.12 Premature Ventricular Contraction (PVC)
- 12.1.13 Temp: T1,T2, Delta T, and T Blood
- 12.1.14 ST
- 12.1.15 Cardiac Output
- 12.1.16 Cardiac Index
- 12.1.17 Pulmonary Artery Wedge Pressure (PAWP)
- 12.1.18 Battery Percentage
- 12.2 Invalid Data Display
- 12.1 Parameter Specifications
- 13.0 Alarms and Events
- 14.0 Network Tab (Optional)
- 14.1 Network Tab
- 14.1.1 Accessing the Network Tab
- 14.1.2 Sorting the Contents of the Network Tab List Box
- 14.1.3 Assigning Patient Tiles in the Network Tab
- 14.1.4 Removing a Patient Tile Assignment in the Network Tab
- 14.1.5 Removing All Patient Tile Assignments in the Network Tab
- 14.1.6 Refreshing the Network Tab List Box
- 14.1.7 Troubleshooting
- 14.1 Network Tab
- 15.0 Paging Tab (Optional)
- 15.1 Paging Password Tab
- 15.2 Paging Tab
- 15.2.1 Accessing the Paging Tab
- 15.2.2 Adding a Pager
- 15.2.3 Assigning a Patient Tile
- 15.2.4 Adding All Patient Tiles to a Pager
- 15.2.5 Removing a Patient Tile Assignment
- 15.2.6 Removing All Patient Tiles from a Pager
- 15.2.7 Editing a Pager
- 15.2.8 Removing a Pager
- 15.2.9 Resending a Failed Page
- 15.2.10 Generating a Paging Report
- 15.2.11 Troubleshooting
- 17.0 Glossary
Panorama™ Operating Instructions 0070-10-0690-01 9 - 37
System Setup Functions Equipment Setup Tab
9.8.6 Troubleshooting
This section lists some of the potential messages and issues that may occur while using the
Equipment tab.
MESSAGE/ISSUE * REASON SOLUTION
Equipment list is full This message appears when
the New button is pressed and
the equipment list contains the
maximum number of
equipment list entries.
Select the OK button to close
the dialog box. Delete a device
from the equipment list.
Illegal Device Tile. Device
Tile must be defined.
Please try again.
This message appears when
the Done button is pressed in
the Equipment Setup tab
before a tile number is
selected.
Select the OK button to close
the dialog box. Select a tile
number in the Tile Number
dialog box.
The Tile button is disabled and
a dash (-) is shown in the Tile
field.
The type of equipment being
entered in the equipment list is
either a Panorama Server or a
Panorama
A tile number cannot be
entered for the Panorama
Server or the Panorama
equipment types.
Invalid Device Type This message appears when
the Done button is pressed in
the Equipment Setup tab
before a device type is
selected.
Select the OK button to close
the dialog box. Select a device
type in the Device Type dialog
box.
Illegal Device Label.
Device Label must be
defined. Please try again.
This message appears when
the Done button is pressed in
the Equipment Setup tab
before a device label is
selected.
Select the OK button to close
the dialog box. Select a device
label in the Device Label
dialog box.
Device Label already
exists! Please enter a
new one
This message appears when a
duplicate device label is
entered in the Device Label
field.
Select the OK button to close
the dialog box. Enter a new
device label in the Device
Label field.
Invalid characters
entered. Please enter a
new label.
This message appears when
invalid characters have been
entered in the Device Label.
The device label can only
contain alphanumeric
characters and underscores
(_).
Select the OK button to close
the dialog box. Enter a valid
De
vice label.
Illegal Device ID. Please
enter a new one.
This message appears when
the Done button is pressed in
the Equipment Setup tab
before a device ID is selected.
Select the OK button to close
the dialog box. Enter a Device
ID in the Device ID dialog box.
Device ID must be 8
characters in length.
This message appears when
the Device ID that was entered
is less than 8 characters in
length. Please refer to the
Device ID setup rules in the
Setting up New Equipment
section.
Select the OK button to close
the dialog box. Enter a Device
ID in the Device ID dialog box.
Device ID must start with
the proper device prefix
This message appears when
the incorrect device prefix is
entered in the Device ID box.
Select the OK button to close
the dialog box. Enter the
correct Device ID prefix.
* Messages are shown in all bold text.