Datasheet

Page 10-2 Sales: 763-571-3121 ¨ Fax: [phone] ¨ www.minco.com Minco Bulletin TS-103(A)
Thermal-Ribbons
Thermal-Ribbons
Thermal-
Ribbons
Thermal-Ribbons and Thermal-Tabs
Install these compact sensors anywhere for accurate point sensing and fast response. All Thermal-Ribbon models conform to
EN60751 Class B tolerance when ordered with a PD platinum element. Thermal-Tab models use a thin-film RTD element.
Dimensions
W×L×T(max.)
Element
options
Insulation Temp.
range
Leadwires Time
constant*
Features Model
Thermal-Ribbons
0.20 × 1.50 × 0.030"
(5.1 × 38.1 × 0.8 mm)
FA Kapton
-200 to 200°C
-328 to 392°F
AWG 34,
PTFE insulated
0.15 sec.
Wire-wound nickel-iron
for high resistance in
small package
S38
0.30 × 0.30 × 0.025"
(7.6 × 7.6 × 0.7 mm)
PD
Kapton with foil
backing
-200 to 200°C
-328 to 392°F
AWG 28,
PTFE insulated
0.15 sec. Wire-wound element S651
0.75 × 0.75 × 0.04"
(19 × 19 × 1.0 mm)
FA Mylar
-200 to 150°C
-328 to 302°F
AWG 30,
PTFE insulated
0.3 sec.
Wire-wound nickel-iron
flat element for high
resistance
S25
Thermal-Tabs
0.20 × 0.50 × 0.08"
(5 × 12 × 2 mm) PD, PF, PW
Kapton with
elastomer cover coat
-50 to 155°C
-58 to 311°F
AWG 26,
PTFE insulated
0.8 sec.
Stocked for immediate
shipment
S665
0.20 × 0.60 × 0.08"
(5×15×2mm)
PD, PF, PW, PS,
NB, NA, NJ
Kapton
-50 to 200°C
-58 to 392°F
AWG 26, PTFE or
Polyimide insulated
1.0 sec. Platinum models in stock S17624
0.20 × 0.60 × 0.08"
(5 × 15 × 2 mm) PD, PF, PW, PS Polyimide film
-50 to 260°C
-58 to 500°F
AWG 26, PTFE or
Polyimide insulated
0.4 sec.
Highest temperature
capability
S100820
0.20 × 0.60 × 0.12"
(5 × 15 × 3 mm) PD, PF, PW
Silicone rubber with
elastomer cover and
foil backing
-50 to 155°C
-58 to 311°F
AWG 24,
Silicone insulated
1.3 sec.
Waterproof; suitable for
continuous immersion
S667
0.20 × 0.60 × 0.07"
(5 × 15 × 1.7 mm) PD, PF, PW Polyimide film
-50 to 200°C
-58 to 392°F
AWG 26, PTFE or
Polyimide insulated
0.6 sec. Thinnest profile S100725
0.30 × 0.60 × 0.10"
(7 × 15 × 2.5 mm)
PD, PF, PW, PS,
NB, NA, NJ
Polyimide film
-50 to 200°C
-58 to 392°F
AWG 22, PTFE or
Polyimide insulated
1.2 sec.
Heavier leadwire for
applications requiring
ruggedized design
S100724
0.40 × 0.80 × 0.08"
(10×20×2mm)
PD, PF, PW, PS,
NB, NA, NJ
Polyimide film
-50 to 200°C
-58 to 392°F
AWG 26, PTFE or
Polyimide insulated
0.9 sec.
Larger surface area for
easier handling and max.
adhesive bond
S100723
0.40 × 0.80 × 0.08"
(10×20×2mm)
PD, PF, PW, PS,
NB, NA, NJ
Silicone rubber
-50 to 220°C
-58 to 428°F
AWG 26, PTFE or
Polyimide insulated
1.5 sec.
High temperature rating,
available with wide range
of element options
S100721
* In water at 1 m/sec.
 T (max.) is over the lead bulge.
IN STOCK
All models in the following lead lengths:
24": S651
36": S38, S25
40" PD or PF only: S100723, S100724, S100725, S100820, S17624
40" with 60" max. PD or PF only: S665, S667
See next page for information on how to order.
® ® ® ® ® ® ® ® ® ® ®
Waterproof model
Model S667 is waterproof and
suitable for continous immersion.
Use it to monitor the temperature
of water in a tank or container, or
on equipment that must withstand
wash-down or immersion.
Check with Minco for suitability in
other liquids.
Leadwire insulation codes
S25, S38, S651, S665, S667 Leave blank
A17624, S100721, S100723, S100724,
S100725, S100820
T = PTFE insulated wires
K = Polyimide insulated wires