Datasheet

40
Introduction
Design
Guide
Polyimide
Heaters
Silicone
Rubber
Heaters (foil)
Standard
Polyimide
& Rubber
Rubber
Heaters
(wire-wound)
Mica Heaters
Thermal-Clear
Heaters
All-Polyimide
Heaters
Sensors,
Controllers &
Accessories
Reference
|
Flexible Heaters Design Guide | www.minco.com
Anti-reset windup: Turns off integral action outside the
proportional band to prevent false accumulation of error during
warmup.
AP (All-Polyimide): Flexible heaters with adhesiveless substrate and
covers. High temperature capabilities to 260°C.
AWG (American Wire Gauge): An indicator of wire diameter.
The larger the number, the smaller the diameter.
Conduction: The transfer of thermal energy between adjacent
bodies (usually solids) or parts of the same body.
Convection: The transfer of thermal energy in fluids and gases by
mixing warmer areas with cooler ones. Convection currents can
form, due to differences in density. Generally, warmer fluids
(or gases) are less dense and tend to rise.
Creep action: A switching method, often used in thermostats,
in which a temperature-sensitive bi-metallic element causes
slow make and break of electrical connections. In contrast to
snap action, this method results in tighter temperature control,
but greater electrical noise and usually shorter life.
Cycle time: The duration of an on/off cycle with time
proportioning. With cycle time of 10 seconds, for example, 80%
power would give 8 seconds on, 2 seconds off. General rule:
Shorter times give better control and less oscillation, but require
solid state relay.
Deadband: The temperature difference between full “on” (when
temperature is falling), and full “off” (when temperature is rising),
for an on/off controller. The deadband is intentionally designed
to reduce oscillation.
Derivative: Adjustment to output based on the process’s rate of
change, usually to allow faster recovery from upsets. Also
expressed as “rate.” General rule: Increase derivative time if
system frequently overshoots; decrease if system acts sluggish.
Dielectric strength: The maximum voltage (typically AC) that an
insulation material can withstand before material break down
occurs.
Droop: An error inherent in simple proportional control where the
temperature reaches equilibrium at a point other than setpoint,
but still within the proportional band.
Etched-foil: A method of producing pre-determined electrical
paths, by chemically removing (etching) the areas which will not
carry electric current. This process can be used to manufacture
heaters, flex-circuits, and temperature sensors.
FEA (Finite Element Analysis): A numerical method used to predict
the behavior of a heater/heat sink design. It is typically employed
only if actual modeling is not practical.
FEP (Fluorinated Ethylene Propylene): A thermoplastic adhesive in
the PTFE family of polymers.
Flex circuit: A printed circuit made with flexible materials for
compact electrical interconnects.
Fuzzy logic: A control scheme that operates in addition to PID and
gives the controller more “common sense” for dealing with
unpredictable systems. Not required for most heating situations.
Heat sink: The body to which a heater is affixed.
Heat transfer: The transfer of thermal energy between bodies of
different temperature.
Heaterstat™: A Minco temperature controller that uses the heating
element as a temperature feedback sensor.
Hysteresis: The temperature difference between full “on” (when
temperature is falling), and full “off” (when temperature is rising),
for an on/off controller.
Insulation resistance: The actual resistance of an electrically
insulating material. Measuring devices typically use high DC
voltage to perform the measurement.
Integral: A controller feature that continuously compensates for
droop by integrating errors over time and adjusting the
proportional band up and down. Also expressed as “reset”
(integral time = 1/reset rate). General rule: Short integral times
give faster correction, but too short causes oscillation.
ISO 9001: A quality management system that is accepted
worldwide.
Laminate: To bond materials using heat and pressure.
Mica: A fairly brittle phyllosilicate mineral used to insulate heaters.
It is used primarily for its high temperature and high watt density
capabilities.
NASA (National Aeronautics and Space Administration): The U.S.
agency for space exploration.
Ohm’s law: E = I •R. See page 6.
On/off: A simple control scheme where output is on below the
setpoint, off above, as with a thermostat.
Outgassing: The expulsion of gases, especially in a vacuum or high
temperature environment.
PID (Proportional, Integral, Derivative): A control algorithm
incorporating proportional, integral, and derivative action.
Polyester: A synthetic polymer used to electrically insulate heaters,
flex-circuits, and Thermal-Ribbons™. It is an economic alternative
to polyimide, when high temperature and chemical resistance are
not critical.
Polyimide (Kapton™): A flexible, amber-colored, translucent film to
electrically insulate heaters, flex circuits, and Thermal-Ribbons™.
It is widely used for its temperature range and resistance to
chemicals. DuPont’s tradename for Polyimide is Kapton™.
Profile: A method of providing uniform temperature, by varying
watt density in a single heater to accommodate non-uniform
heat loss from the heat sink.
Glossary
On
O
Output
Setpoint
Temperature
Average heat sink tem
Temperature above setpoint:
Sensing pulses only
Temperature below setpoint: Each pulse stays on until heat
Scan rate = Preset o time between pulses (0.1 to 10 seconds typical)
Heater element temperature