Datasheet

29
Introduction
Design
Guide
Polyimide
Heaters
Silicone
Rubber
Heaters (foil)
Standard
Polyimide
& Rubber
Rubber
Heaters
(wire-wound)
Mica Heaters
Thermal-Clear
Heaters
All-Polyimide
Heaters
Sensors,
Controllers &
Accessories
Reference
Sal es and Support
Americas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacic: (65) 6511 3388
|
Specifications subject to change
Standard models
One second scan rate.
6" (150 mm) leadwires.
LED power indicator.
Calibration: Setpoint factory-calibrated to specified resistance.
Specification options
CT198-1019 Model number
CT198 = Heaterstat (nominal setpoint)
CT698 = Heaterstat matched to heater
R Setpoint calibration code
R = Nominal heater resistance (CT198)
T = Heaterstat/heater matched set (CT698)
365 Initial calibration setpoint
Setpoint calibration code = R:
Nominal heater resistance at set point
temperature (in ohms).* Must be within
allowable range for specified model.
Setpoint calibration code = T:
Temperature setpoint. Specify temperature
and scale (°C or °F)
Ex: 120F represents 120°F
L Leads
L = Leadwires (standard)
P = Pins (LED not available)
1 Scan rate
0.1 to 10 seconds (1 second standard)
CT198-1019R365L1 = Sample part number
Model
Number
Setpoint range (Ω)
Minimum Maximum
Supply voltage (VDC)
Minimum Maximum
CT198-1000 4.50 6.75 4.75 10
CT198-1001 5.63 8.44 7.5 16
CT198-1002 7.03 10.55 7.5 21
CT198-1003 8.79 13.18 7.5 26
CT198-1004 10.99 16.48 7.5 33
CT198-1005 13.73 20.60 7.5 41
CT198-1006 17.17 25.75 7.5 60
CT198-1007 21.46 32.19 7.5 60
CT198-1008 26.82 40.23 7.5 60
CT198-1009 33.53 50.29 7.5 60
CT198-1010 41.91 62.86 7.5 60
CT198-1011 52.39 78.58 7.5 60
CT198-1012 65.48 98.23 7.5 60
CT198-1013 81.85 122.78 7.5 60
CT198-1014 102.32 153.48 7.5 60
CT198-1015 127.90 191.85 7.5 60
CT198-1016 159.87 239.81 7.5 60
CT198-1017 199.84 299.76 7.5 60
CT198-1018 249.80 374.70 7.5 60
CT198-1019 312.25 468.38 7.5 60
CT198-1020 390.31 585.47 7.5 60
CT198-1021 487.89 731.84 9 60
CT198-1022 609.86 914.80 11 60
DC Power
Supply
Heaterstat
V+
Ground
Out
1 Red
2 Black
3 Orange
High
TCR
Heater
1.50 (38.1)
1.275 (32.4)
1.00
(25.4)
0.25
(6.4)
0.385
(9.8)
0.40
(10.2)
0.10
(2.5)
PINS: 0.025 (0.6)
SQUARE
0.20 (5.1)
0.675
(17.1)
0.045 (1.1) ∅ [3]
0.194
(4.9) ∅
0.160
(4.1) ∅
0.149 (3.8) ∅
SETPOINT ADJUST
0.50
(12.7)
PC BO
ARD
LAYOUT
Wiring diagram
Dimensions in inches (mm)
* To determine heater resistance at temperature T,
go to www.minco.com/ct198.html
Resistance vs. temperature tables are available at:
www.minco.com/sensorcalc/
Heaterstat™ Sensorless DC Controller