Specifications

5-21
Troubles for which error messages are displayed
∗∗∗∗∗ ERROR 51 ∗∗∗∗∗
Y-ORIGIN
Y-origin could not be detected. Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 53 ∗∗∗∗∗
HEAD HEIGHT ORIGIN
Head height origin could not be
detected.
∗∗∗∗∗ ERROR 54 ∗∗∗∗∗
MEDIA JAM
Paper jam was detected. Open the front cover and raise the
clamp lever, and remove the jammed
paper.
If the same error message appears
again even after clearing the paper jam
status, contact your local distributor to
call for service.
∗∗∗∗∗ ERROR 58 ∗∗∗∗∗
POSITION ENCODER:DIR
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 58 ∗∗∗∗∗
POSITION ENCODER:CNT
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 59 ∗∗∗∗∗
CUTTER ENCODER
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 64 ∗∗∗∗∗
TAKE-UP VOLTAGE
Abnormal voltage detected in AMF
media take-up motor.
∗∗∗∗∗ ERROR 64 ∗∗∗∗∗
FEEDER VOLTAGE
Abnormal voltage detected in AMF
media feeding motor.
∗∗∗∗∗ ERROR 64 ∗∗∗∗∗
Small TAKE-UP VOLT.
Abnormal voltage detected in small
take-up motor.
∗∗∗∗∗ ERROR 65 ∗∗∗∗∗
TAKE-UP TENSION BAR
An error occurred during take-up
encoder detection.
(The encoder/sensor is malfunctioning,
or there is no media loaded)
When AMF media take-up device is
not used, set OFF (See 6-21).
If the error appears again after check-
ing the media set, call for service.
∗∗∗∗∗ ERROR 66 ∗∗∗∗∗
FEEDRE TENSION BAR
An error occurred during feeding
encoder detection.
(The encoder/sensor is malfunctioning,
or there is no media loaded)
When AMF media feeding device is
not used, set OFF (See 6-21).
If the error appears again after check-
ing the media set, call for service.
∗∗∗∗∗ ERROR 67 ∗∗∗∗∗
TAKE-UP UNIT 00
An error was detected in the AMF
media take-up unit when the power
was turned on.
(The unit is not installed, or the sensor
is malfunctioning)
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 67 ∗∗∗∗∗
TAKE-UP UNIT 01
Check whether the AMF media take-
up unit is disconnected.
∗∗∗∗∗ ERROR 67 ∗∗∗∗∗
TAKE-UP UNIT 04
Check whether the AMF media take-
up unit sensor is malfunctioning.
∗∗∗∗∗ ERROR 67 ∗∗∗∗∗
FEEDRE UNIT 00
An error was detected in the AMF
media feeding unit when the power
was turned on.
(The unit is not installed, or the sensor
is malfunctioning)
Error message Cause Remedy