Specifications

5-23
Troubles for which error messages are displayed
∗∗∗∗ ERROR 122 ∗∗∗∗
CONDENSATION
As the ambient temperature is low,
head condensation may occur.
Raise the ambient temperature.
(To use without changing the setting,
press the [ENTER] key.)
∗∗∗∗ ERROR 134 ∗∗∗∗
MEDIA ENCODER:SENSOR
An error occurred in detection by the
media encoder.
(Counting impossible)
Select “NORMAL” in [MediaFeed
SETUP] - [FEED METHOD] or turn
off the power to the printer and turn it
on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗ ERROR 134 ∗∗∗∗
MEDIA ENCODER:DIR.
An error occurred in detection by the
media encoder.
(Wrong orientation)
∗∗∗∗ ERROR 134 ∗∗∗∗
MEDIA ENCODER:ORIGIN
An error occurred in detection by the
media encoder.
(Origin detection impossible)
∗∗∗∗ ERROR 135 ∗∗∗∗
MEDIA FEED UNUSUAL
An error occurred in media feed. Check that the media has been set
properly, and the media still remains.
Using [SET UP] - [MediaFeed
SETUP] - [MOVEMENT TEST], per-
form testing to see if the media is com-
patible with direct feed.
If the error status is not cleared even
with a proper media, select “NOR-
MAL” in [SET UP] - [MediaFeed
SETUP] - [FEED METHOD] or turn
off the power to the printer and turn it
on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗ ERROR 142 ∗∗∗∗
INK LEAK
Ink leakage was detected. Turn off the power to the printer and
turn it on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗ ERROR 143 ∗∗∗∗
CARTRIDGE SOLENOID
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 143 ∗∗∗∗
WASH CART. SOLENOID
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 144 ∗∗∗∗
CARTRIDGE SET !
An error occurred in the control sys-
tem.
Set a cartridge.
∗∗∗∗ ERROR 145 ∗∗∗∗
FlushingBOX EXCHANGE
Time for replacing the flushing box has
passed.
Make a call for services.
∗∗∗∗ ERROR 145 ∗∗∗∗
FlushingBOX CLEANING
Time for cleaning the flushing box. Promptly clean the flushing box.
(See 4-42)
∗∗∗∗ ERROR 146 ∗∗∗∗
It can't be CLEANING
Cleaning can not be performed as the
quantity of ink per one supply channel
is too little or finished.
Confirm the supply channel in the
local mode and replace the cartridge.
(See 3-67)
∗∗∗∗ ERROR 160 ∗∗∗∗
NCU DETECT 00
An error occurred in the control sys-
tem.
Printing can be resumed after turning
off the nozzle missing detection func-
tion. Turn on the nozzle missing detec-
tion function again before starting to
print the next and subsequent print
files.
If the error occurs frequently, contact
your local distributor to call for ser-
vice.
∗∗∗∗ ERROR 160 ∗∗∗∗
NCU DETECT 01
An error occurred in the control sys-
tem.
Error message Cause Remedy