Specifications

5-21
Troubles for which error messages are displayed
∗∗∗∗∗ ERROR 51 ∗∗∗∗∗
Y-ORIGIN
Y-origin could not be detected. Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 53 ∗∗∗∗∗
HEAD HEIGHT ORIGIN
Head height origin could not be
detected.
∗∗∗∗∗ ERROR 54 ∗∗∗∗∗
MEDIA JAM
Paper jam was detected. Open the front cover and raise the
clamp lever, and remove the jammed
paper.
If the same error message appears
again even after clearing the paper jam
status, contact your local distributor to
call for service.
∗∗∗∗∗ ERROR 58 ∗∗∗∗∗
POSITION ENCODER:DIR
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 58 ∗∗∗∗∗
POSITION ENCODER:CNT
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 59 ∗∗∗∗∗
CUTTER ENCODER
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 64 ∗∗∗∗∗
TAKE-UP VOLTAGE
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 64 ∗∗∗∗∗
FEEDER VOLTAGE
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 116 ∗∗∗∗
NCU I/F 00
An error occurred in the control sys-
tem.
Operation can be resumed after turning
off the nozzle missing detection func-
tion.
Turn off the power to the printer and
turn it on after a while.
If the error occurs frequently, contact
your local distributor to call for ser-
vice.
∗∗∗∗ ERROR 116 ∗∗∗∗
NCU I/F 01
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 120 ∗∗∗∗
ENVIRONMENT TEMP(LO)
The ambient temperature is outside the
permissible temperature range (too
low).
Adjust the ambient temperature within
a range of available ambient tempera-
ture.
∗∗∗∗ ERROR 121 ∗∗∗∗
ENVIRONMENT TEMP(HI)
The ambient temperature is outside the
permissible temperature range (too
high).
∗∗∗∗ ERROR 122 ∗∗∗∗
ENV.TEMP.LO:DewDrops
As the ambient temperature is low,
head condensation may occur.
Raise the ambient temperature.
(To use without changing the setting,
press the [ENTER] key.)
∗∗∗∗ ERROR 134 ∗∗∗∗
MEDIA ENCODER:SENSOR
An error occurred in detection by the
media encoder.
(Counting impossible)
Select “NORMAL” in [MediaFeed
SETUP] - [FEED METHOD] or turn
off the power to the printer and turn it
on after a while.
If the same error message appears
again, contact your local distributor to
call for service.
∗∗∗∗ ERROR 134 ∗∗∗∗
MEDIA ENCODER:DIR.
An error occurred in detection by the
media encoder.
(Wrong orientation)
∗∗∗∗ ERROR 134 ∗∗∗∗
MEDIA ENCODER:ORIGIN
An error occurred in detection by the
media encoder.
(Origin detection impossible)
Error message Cause Remedy