Specifications

5 In Case of Trouble
5-20
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
PACKET SIZE OVER
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
Check that the cable is securely con-
nected to the host computer and inter-
face board. Also, check to see if any
error has occurred on the host com-
puter.
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
USB PROTOCOL
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
USB ENVIRONMENT
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
USB DATA
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
∗∗∗∗∗ ERROR 30 ∗∗∗∗∗
OPERATION ERROR
Improper operation was conducted on
the operation panel.
The Display 1 shows the cause of the
error.
Remove the cause, and perform a
proper operation.
∗∗∗∗∗ ERROR 34 ∗∗∗∗∗
DATA REMAIN
It is being tried to change settings for
functions though there remains
received data that has not yet been
printed.
Print all the received data or execute
the data clear function. Then, change
settings.
∗∗∗∗∗ ERROR 40 ∗∗∗∗∗
MOTOR ALARM X
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 41 ∗∗∗∗∗
MOTOR ALARM Y
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 42 ∗∗∗∗∗
X OVER CURRENT
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 43 ∗∗∗∗∗
Y OVER CURRENT
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 45 ∗∗∗∗∗
CAPPING : SENSOR
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 45 ∗∗∗∗∗
CAPPING : PARAMETER
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 46 ∗∗∗∗∗
WIPER
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 47 ∗∗∗∗∗
STATION
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 49 ∗∗∗∗∗
CUTTER SOLENOID
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 50 ∗∗∗∗∗
MEDIA DETECT
Paper could not be detected. The media
set position or media itself is not
proper.
If the same error message appears
again even after setting the media
properly, contact your local distributor
to call for service.
∗∗∗∗∗ ERROR 50 ∗∗∗∗∗
THICKNESS DETECT
Media thickness could not be detected. Input the media thickness or select the
END key and execute media detection
again.
Error message Cause Remedy