Specifications

5 In Case of Trouble
5-18
Error messages
Error messages indicates error numbers.
If any error message is displayed, turn off the power to the printer and turn it on after a while.
If the same error message appears again, contact your dealer or an office of MIMAKI to call for service.
Error message Cause Remedy
∗∗∗∗∗ ERROR 01 ∗∗∗∗∗
MAIN ROM
An error occurred in the circuit board
system.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 02 ∗∗∗∗∗
MAIN RAM
An error occurred in the circuit board
system.
∗∗∗∗∗ ERROR 03 ∗∗∗∗∗
POWER +3.3V
An error occurred in the circuit board
system.
∗∗∗∗∗ ERROR 03 ∗∗∗∗∗
POWER +5V
An error occurred in the circuit board
system.
∗∗∗∗∗ ERROR 03 ∗∗∗∗∗
POWER +24V
An error occurred in the circuit board
system.
∗∗∗∗∗ ERROR 03 ∗∗∗∗∗
POWER +42V
An error occurred in the circuit board
system.
∗∗∗∗∗ ERROR 04 ∗∗∗∗∗
F-ROM
An error occurred in the circuit board
system.
∗∗∗∗∗ ERROR 06 ∗∗∗∗∗
SD-RAM
An error occurred in the circuit board
system.
∗∗∗∗∗ ERROR 07 ∗∗∗∗∗
HEAD (----)
An error in heads was detected.
∗∗∗∗∗ ERROR 07 ∗∗∗∗∗
VOLTAGE (----)
An error in heads was detected.
∗∗∗∗∗ ERROR 07 ∗∗∗∗∗
POWER 01 (----)
An error occurred in the head power
supply during preparation of this
machine.
∗∗∗∗∗ ERROR 07 ∗∗∗∗∗
POWER 02 (----)
An error occurred in the head power
supply during printing.
∗∗∗∗∗ ERROR 08 ∗∗∗∗∗
LinearENCODER:SENSOR
An error occurred in the linear encoder.
∗∗∗∗∗ ERROR 08 ∗∗∗∗∗
LinearENCODER:DIR.
An error occurred in the linear encoder.
∗∗∗∗∗ ERROR 08 ∗∗∗∗∗
LinearENCODER:COUNT
An error occurred in detection by the
linear encoder.
(Read-out count error)
∗∗∗∗∗ ERROR 09 ∗∗∗∗∗
FPGA ERROR
An error occurred in the circuit board
system. (FPGA PDC)
∗∗∗∗∗ ERROR 09 ∗∗∗∗∗
HDC ERROR (----)
An error occurred in the circuit board
system. (FPGA HDC)
∗∗∗∗∗ ERROR 09 ∗∗∗∗∗
HEAT SINK (----)
Abnormal temperature is detected at
the control panel.
∗∗∗∗∗ ERROR 09 ∗∗∗∗∗
Slight VIBRAT. (----)
An error occurred in the circuit board
system. (FPGA HDC)