Specifications

Troubles for which error messages are displayed
4-11
<LOCAL.1> [#01]
INK END MCYK
Ink for one supply path has
been completely used up.
Replace the ink cartridge for the supply
path corresponding to the indicated
color.
←
*REMOTE.1* [#01]
INK END MCYK
<LOCAL.1> !CART [#01] There is a problem with
installed ink cartridges.
(If this occurs together with
any other warning, the display
shows [<LOCAL.1> !CAR/
WASH] instead of [#**].)
Check the content of the warning by
displaying it using the guidance func-
tion.
←
*REMOTE.1* !CART [#01]
<LOCAL.1> !WASH [#01] There is a problem with the
installed washing solution car-
tridge.
(If this occurs together with
any other warning, the display
shows [<LOCAL.1> !CAR/
WASH] instead of [#**].)
Check that the washing solution car-
tridge has been set properly.
←
*REMOTE.1* !WASH [#01]
INK NEAR END
MMCC - - - -
The ink of the ink cartridge has
been nearly used up.
Replace the ink cartridge generating
the warning with a new one.
1. Check that the cartridge end sensor
works properly with [#TEST] - [INK
CARTRIDGE].
2. Check the end board of the cartridge.
3. .Replace the sensor with a new one.
INK END
MMCC - - - -
The ink of the ink cartridge has
been completely used up.
Replace the ink cartridge generating
the warning with a new one.
1. Check the end board of the cartridge.
2. Replace the sensor with a new one.
NON-ORIGINAL INK
MMCC - - - -
The ink cartridge is not
MIMAKI genuine.
Or, the ink IC chip can not be
read.
Replace the warned ink cartridge with
a MIMAKI genuine one, or insert the
ink cartridge again.
1. Make sure that [#TEST] - [INK CAR-
TRIDGE] - [INK-IC CHECK] is per-
formed properly.
2. Replace the ID point of contact PCB
with a new one.
WRONG INK IC
MMCC - - - -
The IC chip of the ink cartridge
cannot be read normally.
Remove the ink cartridge generating
the warning once and install it again.
If the same warning message still
appears, contact your local distributor
to call for service.
1. Make sure that [#TEST] - [INK CAR-
TRIDGE] - [INK-IC CHECK] is per-
formed properly.
2. Replace the ID point of contact PCB
with a new one.
Kind of INK
MMCC - - - -
The ink of the ink cartridge is
different in type from the ink
currently supplied.
Check the ink type of the ink cartridge
generating the warning.
←
Color of INK
MMCC - - - -
The ink of the ink cartridge is
different in color from the ink
currently supplied.
Check the ink color of the ink cartridge
generating the warning.
←
WRONG CARTRIDGE
MMCC - - - -
There is trouble with an
installed ink cartridge.
Check the ink cartridge generating the
warning.
←
NO CARTRIDGE
MMCC - - - -
An ink cartridge has not been
installed in the slot.
Install an appropriate ink cartridge in
the slot generating the warning.
If the error occurs frequently after
replacing ink cartridges, execute the fol-
lowings.
1. Check that the cartridge exist/non-
exist sensor works properly with
[#TEST] - [INK CARTRIDGE].
2. If it does not work properly, replace
the sensor or X-axis motor relay PCB
with a new one.
Expiration
MMCC - - - -
The specified expiration date
of an ink cartridge has passed.
Replace the ink cartridge generating
the warning with a new one.
* The ink cartridge may be used until
one month passes after the specified
expiration date.
←
<Warning messages and corrective measures (continued) >
Display Cause
Remedy (instruction & maintenance manual)
Descriptions in the manual
(for reference)
Remedy