Specifications

Color Inkjet Printer JV33-130/160
4-8
E84 h'******** Verify error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E85 ROM HASH Hash check error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E90 h'******** ROM Erase error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E92 h'******** ROM Write error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E95 MODE SHIFT Transition to the version
up mode is not allowed.
(As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E99 VERSION DATA Wrong version data. (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
–––
ERROR
120
ENVIRONMENT
TEMP(LO)
The ambient temperature
is outside the permissi-
ble temperature range
(too low).
Adjust the ambient temperature of the
printer.
To continue operation without chang-
ing the ambient conditions, press the
[ENTER] key.
Operation under the temperature among the
guaranteed operation temperature range is
recommended.
ERROR
121
ENVIRONMENT
TEMP(HI)
The ambient temperature
is outside the permissi-
ble temperature range
(too high).
ERROR
144
CARTRIDGE SET
!
An ink cartridge is not
set.
Set an ink cartridge. It is explained that leaving a state without set-
ting a ink cartridge may cause inability of ink
sucking because needles of the slot are dehy-
drated.
ERROR COM-
MAND
(This error does not occur on site.) Confirm the USB cable. (specifications, cable
length and so on)
ERROR PARAM-
ETER
(This error does not occur on site.) Make sure that PRM file, parameter data cor-
respond to version of the device.
ERROR DATA (This error does not occur on site.) Confirm the USB cable. (specifications, cable
length and so on)
ERR PRM.
SHORTAGE
(This error does not occur on site.) Make sure that PRM file, parameter data cor-
respond to version of the device.
ERROR
200
HEAD MEMORY
(----)
An error occurred in
head unit memory.
Turn the main power OFF and turn the
main power ON after elapse of 2~3
minutes. In a case of recurrence, con-
tact your local distributor to call for
service.
1. Check the head memory cable.
2. Replace the head memory with a new one.
3. Replace the ink slider PCB with a new
one.
4. Replace the main PCB with a new one.
ERROR
211
HeaterTEMP
(--/--/--)
An abnormal tempera-
ture of the media heater
is detected.
Turn the main power OFF and turn the
main power ON after elapse of 2~3
minutes. In a case of recurrence, con-
tact your local distributor to call for
service.
1. Replace the main PCB with a new one.
2. Replace the power supply PCB with a new
one.
3. Replace the corresponding platen cover
with a new one.
HeadWARM.
TEMP. (----)
An abnormal tempera-
ture of the head heater
was detected.
1. Make sure that the connection to the main
FPC is correct.
2. Replace the corresponding head heater
with a new one.
3. Replace the ink slider PCB with a new
one.
HeadWARM.
BREAK(----)
The head heater is dis-
connected.
HeadWARM.
THERM(----)
Trouble has occurred
with the thermistor of
the head heater.
<Error messages and corrective measures (continued) >
Display
Cause
Remedy (instruction & maintenance manual)
ERROR
No.
ERROR
Descriptions in the manual
(for reference)
Remedy