Specifications

Troubles for which error messages are displayed
4-7
ERROR
45
CAPPING :
PARAMETER
An error occurred in
capping control.
(Improper parameter
adjusted value)
Turn the main power OFF and turn the
main power ON after elapse of 2~3
minutes. In a case of recurrence, con-
tact your local distributor to call for
service.
1. Make sure that the adjusting value of
[#ADJUST] - [CAPPING] is set correctly.
ERROR
46
WIPER An error occurred in
wiper control.
Turn the main power OFF and turn the
main power ON after elapse of 2~3
minutes. In a case of recurrence, con-
tact your local distributor to call for
service.
1. Check that the wiper sensor functions
properly with [#TEST] - [SENSOR
TEST].
2. Check that the wiper motor functions
properly with [#TEST] - [MOTOR TEST].
3. Make sure that there is no friction on the
guide rail caused by sticking of ink.
4. Replace the wiper sensor with a new one.
5. Replace the stepping motor with a new
one.
6. Replace the station PCB with a new one.
ERROR
50
MEDIA DETECT Paper could not be
detected.
The media set position
or media itself is not
proper.
If the same error message appears
again even after setting the media prop-
erly, contact your local distributor to
call for service.
1. Make sure that there is no gap between the
end faces of platen and platen rubber.
2. Execute [#TEST] - [PAPER SENSOR] to
obtain sensor values at the media exist
position and media non-exist position.
When the difference of values is more than
±50, detection is allowed.
If the difference is smaller, execute the fol-
lowings.
3. Clean the paper width sensor or replace
with a new one.
4. Replace the ink slider PCB with a new
one.
ERROR
51
Y-ORIGIN Y-origin could not be
detected.
Turn the main power OFF and turn the
main power ON after elapse of 2~3
minutes. In a case of recurrence, con-
tact your local distributor to call for
service.
1. Check that the Y origin sensor works prop-
erly with [#TEST] - [SENSOR TEST].
2. Replace the Y origin sensor with a new
one.
3. Replace the station PCB with a new one.
E70 FPGA FPGA Configuration
fails.
(As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E71 SD-RAM Abnormal operation in
SD-RAM
(As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Make sure that PRAM PCB is connected
properly.
2. Replace the PRAM PCB or main PCB
with a new one.
E74 TRANS DATA Received data is not Ver-
sion Up file
(As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Make sure that the ROM file is transmit-
ted.
E80 ROM0 ERASE ROM0 Erase error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E81 ROM1 ERASE ROM1 Erase error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E82 h'******** ROM0 Write error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
E83 h'******** ROM1 Write error (As the support functions will be sup-
ported after the releasing, this error
does not arise on site in the present.)
1. Replace the main PCB with a new one.
<Error messages and corrective measures (continued) >
Display
Cause
Remedy (instruction & maintenance manual)
ERROR
No.
ERROR
Descriptions in the manual
(for reference)
Remedy