Operator's Manual

5
MAINTENANCE
WARNING
To reduce the risk of injury, always
WARNING
Chemical Burn Hazard.
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE
®
service facility for ALL repairs.
Maintaining Tool
ONE-KEY™
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or
entered the body, seek immediate medical atten-
tion.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
adjust speed, or if the Bluetooth communication stops
working, remove and reinsert the coin cell battery to
reset. Replace the battery if the problem continues.
To remove/replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery, keep it away from children,
and dispose of it properly.
4. Insert the new battery (3V CR2032), with the posi-
tive side facing up.
5. Close the battery door and tighten the screw(s)
securely.
WARNING
T
jury and
o reduce the risk of personal in
damage, never immerse
-
your tool, battery pack or charger in liquid or
Repairs
For repairs, return the tool, battery pack and charger
to the nearest service centre.
ACCESSORIES
WARNING
Use only recommended accesso-
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
combustible solvents around tools.
ries. Others may be hazardous.
Impacting Techniques
The longer a bolt, screw, or nut is impacted, the
tighter it will become. To help prevent damaging
the fasteners or workpieces, avoid excessive
impacting. When using preset modes 1-3, pull and
hold the trigger for two complete cycles to reach
indicated torque range. Set the Mode properly
for the workpiece. Be particularly careful when
impacting smaller fasteners because they require
less impacting to reach optimum torque.
Practice with various fasteners, noting the length of
time required to reach the desired torque. Check the
tightness with a hand-torque wrench. If the fasteners
are too tight or too loose, change the impacting time
or select a more appropriate mode.
Oil, dirt, rust or other matter on the threads or under the
The torque required to loosen a fastener averages
75% to 80% of the tightening torque, depending on
the condition of the contacting surfaces.
On light gasket jobs, run each fastener down to a
relatively light torque and use a hand torque wrench
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage
of parts, or any other condition that may affect the
tool operation. Return the tool, battery pack, and
charger to a MILWAUKEE
®
service facility for
repair. After six months to one year, depending on
use, return the tool, battery pack and charger to a
MILWAUKEE
®
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE
®
service facility for repairs.
For a complete listing of accessories, go online to
milwauketool.com.au/ milwaukeetool.co.nz or
contact a distributor.