Operator's Manual
4
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Forward
Push for rof hsuP
Reverse
1.
2.
PUSH TO CENTRE TO LOCK
3. To lock the trigger, push the control switch to the
For forward (clockwise) rotation, push the control
switch in the direction shown. Check the direction
of rotation before use.
For reverse (counterclockwise) rotation, push the
control switch in the direction shown. Check the
direction of rotation before use.
Starting, Stopping and Controlling Speed
These tools may be operated at any speed from 0
to full speed.
1.
To start the tool, pull the trigger.
centre position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance or changing accessories. Always
lock the trigger or remove the battery pack before
storing the tool and any time the tool is not in use.
2.
To vary the driving speed, increase or decrease
pressure on the trigger. The further the trigger is
pulled, the greater the speed.
ONE-KEY™ Indicator
Solid Blue
ONE-KEY™
Blinking Blue
Wireless mode is active and ready
app.
NOTE: An LED is turned on when the trigger is pulled.
For best results when using preset modes, pull and
hold the trigger until the tool automatically stops.
Refer to the ONE-KEY™ App for proper impacting
techniques.
Blinking Red
Tool is actively communicating with
the ONE-KEY™ app.
3. To stop the tool, release the trigger.
Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
Mode
Indicator
OPERATION
e
-
-
WARNING
c
A
h
lw
a
ays
nging
rem
o
o
r
ve
rem
b
o
attery
ving
p
ack
access
befor
o
mode indicator is lit, begin
ONE-KEY™
modes. When the desired
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
Using the Drive Control
The drive control button is used to adjust the torque,
rotation speed (RPM), and impact speed (IPM) for
the application.
Drive Control Button
To select the drive control mode:
1. Pull and release the trigger
to turn on the tool. The cur-
rent mode indicator is lit.
2. Press the drive control but-
ton to cycle through the
work.
When connected to the ONE-KEY™ App on your
smart device, the wireless LED will light.
MODE RPM IPM Nm SHUT OFF
AUTO POWER
REVERSE
FULL
1 0-1200 0-1600
†
YES YES
2 0-1800
†
0-2400 YES YES
3 0-1800
†
0-2400 YES YES
4 0-1800 0-2400 NO YES
reach indicated torque range.
†
Pull and hold the trigger for two complete cycles to
ASSEMBLY
WARNING
Recharge only with the charger
-
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
NOTE: Select the torque range in accordance with
.snoitcurtsni gninetsaf srerutcafunam tnempiuqe eht
For best results when using preset modes, pull and
hold the trigger until the tool automatically stops.
Refer to the ONE-KEY™ App for proper impacting
WARNING
changing or removing accessories.
Always remove battery pack before
accessorie
WARNING
rec
Only
o
use s
for thimmended
may be hazardous.
s tool. Others
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
-
cally designed for use on impact wrenches and
drivers. Other sockets and accessories might
shatter or break causing injury.
Attaching and Removing Accessories
the anvil.
54-102 Nm
102-203 Nm
1016 Nm Max.
372-610 Nm
1. Use only the appropriate size Square Drive Sockets.
2. To attach a socket, align the accessory with the
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com.au/one-key.
To download the ONE-KEY™ app, visit the App
Store or Google Play from your smart device.